+- STD (https://www.superturbodiesel.com/std)
+-- Forum: Tuning (https://www.superturbodiesel.com/std/forumdisplay.php?fid=6)
+--- Forum: Engine (https://www.superturbodiesel.com/std/forumdisplay.php?fid=7)
+--- Thread: what turbo is this? (/showthread.php?tid=861)
what turbo is this? - lars - 11-19-2009
http://www.blocket.se/varmland/Audi_VW_Turbo__common_rail_23271101.htm?ca=4&w=3&last=1
The seller says he has a few from a audi 3,0 tdi. As new, he claims.
Are these a pain to convert to actuator operation?
What is it called? Will it be waay too big for my stock 602(later pressure than stock)?
If I buy one, will it be decent for a street machine 4500rpm future 7 or 7,5mm pump? thanks
RE: what turbo is this? - winmutt - 11-19-2009
Should be a KKK BV50, IIRC they use the same controller as the Holset. VNT/VGT turbo with similar trim as a GT2559V. Potentially a great turbo, impossible to find over here. Whats the exhaust flange look like? He also has a GT2559V for sale, which uses the Hella actuator.
RE: what turbo is this? - lars - 11-23-2009
thanks. kkk sounds too rare. Should I buy the gt2559v? The price is good. It is also on the c30 cdi amg. hmm good shit.
Will it fit an upcoming 7mm modification on the 602?
Will i get boost later than stock if i attach it to a unmodified 602td?
RE: what turbo is this? - lars - 11-26-2009
Nobody has an idea
...?
RE: what turbo is this? - tomnik - 11-27-2009
Thanksgiving!
(11-23-2009, 04:39 PM)lars thanks. kkk sounds too rare. Should I buy the gt2559v? The price is good. It is also on the c30 cdi amg. hmm good shit.If the price is good, buy it. (what is the price btw.?)
(11-23-2009, 04:39 PM)lars Will it fit an upcoming 7mm modification on the 602?All further modification for (intelligent) more fuel will make you happy.
When you have an offer for the 7mm mod, let me know, I might beat it.
(11-23-2009, 04:39 PM)lars Will i get boost later than stock if i attach it to a unmodified 602td?You will definitely get boost earlier, VTG!
Tom
RE: what turbo is this? - lars - 12-07-2009
The turbos he is selling is garrett m10, m53 and kkk bv50. I do not want to have kkk. I have tried to google the m codes, but nothing useful happens. Does these have a gt....v designation?, and which would fit om 602 best? asking Price is 400usd.
I understand one of those M models are 2559v.!?
RE: what turbo is this? - ForcedInduction - 12-07-2009
M53 is cast onto the compressor housing. It doesn't have any meaning but sellers see it and write it down anyways.
RE: what turbo is this? - lars - 12-08-2009
Can somebody(FI?) give me a second opinion that it really is a 2559v, the one with m53 cast? He has two of those in immaculate condition.
Is the vnt15 he also sells a tuning turbo, or is it just a stock 1,9tdi tinymill? Maybe I`ll just buy that as well, and trade it, if the price is right.
RE: what turbo is this? - ForcedInduction - 12-08-2009
It looks like it, but its hard to be sure since the data tag is too blurry to make anything out.
RE: what turbo is this? - awsrock - 12-13-2009
Be careful if you decide to go for it...I think some of the very small VW turbos (GT15, 17 maybe) look like the GT2559. I can't be sure by the picture, but it looks a bit small to be the 2559.
RE: what turbo is this? - lars - 12-13-2009
Thanks for replies guys.
http://www.blocket.se/skaraborg/Turbo_Garrett_GT2056V_23944476.htm?ca=3&w=3
This gt2056v suddenly appeared to me. Talked to the guy, and he told the bearings were replaced by the previous owner. He is selling it due to changes in plans. He tested it, and vanes are not sticky.
Are these bearings replacable at all, or is he BSing me? Is 10mm wrench the tool to bring to open the turbo?
This will simplify life and cashflow. 7mm, 2559v and MT swap is now delayed on undetermined time.
Seems like a good fit to the 602,(maybe 2052 is better, but hell..?) when compared to other vehicles that comes stock with this turbo. http://www.dieselevante.it/turbochargers.asp?idfam=GT2056V
Just read BGkast`s thread on the sticky, and that contains my deleted questions. sweet
RE: what turbo is this? - awsrock - 12-13-2009
Not sure on the 2056, but to get the housings off of the 2256 it is a 10mm. I'm guessing it is probably the same.