Maxing out 5.5 elements on M pump?
Maxing out 5.5 elements on M pump?
1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
I did this on the MW by turning the holders. For the M pump is it just a matter of unlocking the element arm at the rack and advancing it forward? Will it stop somewhere? Meken any advice while I patiently wait for your elements to come down from the heavens? Also I was thinking about taking 6 k type couplers and putting them in the gp holes and then measuring temp to try to balance the elements, a poor mans bosch bench. Took the millivolt timing method thread to the next level. Thoughts?
1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
Adjust the governor instead so that you will have a longer rack travel.
I would not loosen the elementarms from the rack. You will never be able to balance them again without putting the pump on a bench. I don't think you can adjust them by temperature alone, too many factors will affect the reading.
Adjust the governor instead so that you will have a longer rack travel.
(05-10-2012, 05:56 AM)winmutt So there is no max stop?No, there is no max stop you can adjust yourself on these m-pumps. Adjust the fuel screw, the stop screw behind the back cover
You can also shims the spring(dont remember the name) on the guvenor...It`s is very easy! I adjusted my car with the backcover of while it was running, and i remember that i bottomed the stop screw, had a least 4-5 turns on the fuel screw(these two screws are turned the same amount)+ adjusted the spring with 1mm i think. I adjusted it so it was right before runaway! It was a bit slow form high rpm and down to idle, but it was not that bad
Workd like a treat!
EDH_Performance
05-10-2012, 06:15 AM #5(05-10-2012, 05:56 AM)winmutt So there is no max stop?No, there is no max stop you can adjust yourself on these m-pumps. Adjust the fuel screw, the stop screw behind the back cover
You can also shims the spring(dont remember the name) on the guvenor...It`s is very easy! I adjusted my car with the backcover of while it was running, and i remember that i bottomed the stop screw, had a least 4-5 turns on the fuel screw(these two screws are turned the same amount)+ adjusted the spring with 1mm i think. I adjusted it so it was right before runaway! It was a bit slow form high rpm and down to idle, but it was not that badWorkd like a treat!
Due to piss poor planning I just now got done (I did remove the manifold). Worth the effort. 2 Turns and its a bit different in the uppers on my quick run. I'll know more tomorrow after my commute. EDH, how many turns did you end up doing?
1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
4 bolts and 6 screws? Sound like an easy lunch project when you are working from home.
Due to piss poor planning I just now got done (I did remove the manifold). Worth the effort. 2 Turns and its a bit different in the uppers on my quick run. I'll know more tomorrow after my commute. EDH, how many turns did you end up doing?
1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
(05-11-2012, 12:32 AM)winmutt 4 bolts and 6 screws? Sound like an easy lunch project when you are working from home.
Due to piss poor planning I just now got done (I did remove the manifold). Worth the effort. 2 Turns and its a bit different in the uppers on my quick run. I'll know more tomorrow after my commute. EDH, how many turns did you end up doing?
I don`t remember exactly, but it was 4 or 5 turns on the fuel screw, and the same to the stop screw. I remeber that the stop screw was all the way out, and bottomed. I shimsed the Torque Control Capsule a bit much, then it had a runaway...But i took shims from the one side, and put it on the other side, very easy when you have the backcover off
EDH_Performance
05-11-2012, 02:52 AM #8(05-11-2012, 12:32 AM)winmutt 4 bolts and 6 screws? Sound like an easy lunch project when you are working from home.
Due to piss poor planning I just now got done (I did remove the manifold). Worth the effort. 2 Turns and its a bit different in the uppers on my quick run. I'll know more tomorrow after my commute. EDH, how many turns did you end up doing?
I don`t remember exactly, but it was 4 or 5 turns on the fuel screw, and the same to the stop screw. I remeber that the stop screw was all the way out, and bottomed. I shimsed the Torque Control Capsule a bit much, then it had a runaway...But i took shims from the one side, and put it on the other side, very easy when you have the backcover off
i learned this also, when you turn up the fuel screw to nearly runaway, back off the stop screw on the throttle lever, (as if your dropping idle speed) and runaway is no more, so give her more fuel and everytime you get near runaway back off the stop screw and then more fuel.
hi
i learned this also, when you turn up the fuel screw to nearly runaway, back off the stop screw on the throttle lever, (as if your dropping idle speed) and runaway is no more, so give her more fuel and everytime you get near runaway back off the stop screw and then more fuel.
Been driving the car today, I gained at least 10-20hp. Out ran a 2.8 e30? today! Even though I turned in my ALDA a full turn I am pushing out way more smoke still.....
1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
Are you talking about 2b or 2f?
Been driving the car today, I gained at least 10-20hp. Out ran a 2.8 e30? today! Even though I turned in my ALDA a full turn I am pushing out way more smoke still.....
1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
(05-12-2012, 02:31 PM)winmutt Are you talking about 2b or 2f?hi,
Been driving the car today, I gained at least 10-20hp. Out ran a 2.8 e30? today! Even though I turned in my ALDA a full turn I am pushing out way more smoke still.....
2b, screw this way back and max the fuel.
I have 6mm elements if anyone interested.
(05-12-2012, 02:31 PM)winmutt Are you talking about 2b or 2f?hi,
Been driving the car today, I gained at least 10-20hp. Out ran a 2.8 e30? today! Even though I turned in my ALDA a full turn I am pushing out way more smoke still.....
2b, screw this way back and max the fuel.
I have 6mm elements if anyone interested.
4 Guest(s)
4 Guest(s)