STD Other Projects led panzer's 1985 300D

led panzer's 1985 300D

led panzer's 1985 300D

 
  • 3 Vote(s) - 3.67 Average
 
Pages (2): 1 2 Next
led-panzer
Holset

541
10-30-2010, 09:09 PM #1
Hello,
This is my first post here, but ive been reading the site now for a couple months, i think ive read almost all the posts Big Grin. This car was given to me because my 87 year old grandma smshed it into a schoolbus full of kids Dodgy It was such a beatiful car I coudnt let them scrap it so i rented a u haul and went to get it. So far i have $850 into it and its almost done im just about to start preping for paint. I have pictures to add but i cant figure out how to do it for some reason what am i missing?

1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
10-30-2010, 09:09 PM #1

Hello,
This is my first post here, but ive been reading the site now for a couple months, i think ive read almost all the posts Big Grin. This car was given to me because my 87 year old grandma smshed it into a schoolbus full of kids Dodgy It was such a beatiful car I coudnt let them scrap it so i rented a u haul and went to get it. So far i have $850 into it and its almost done im just about to start preping for paint. I have pictures to add but i cant figure out how to do it for some reason what am i missing?


1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake

Captain America
Boostin' & Roostin'

2,221
10-30-2010, 09:30 PM #2
Way to go grandma! I'm serious! I mean not for the Benz... Sad

Welcome!

Ok:

1st click preview post
2. next to new attachment click browse
3. select your pic.
4. click update attachment button
5. click insert into post button


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
10-30-2010, 09:30 PM #2

Way to go grandma! I'm serious! I mean not for the Benz... Sad

Welcome!

Ok:

1st click preview post
2. next to new attachment click browse
3. select your pic.
4. click update attachment button
5. click insert into post button



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

led-panzer
Holset

541
10-30-2010, 09:31 PM #3
Turns out the pictures are too big.Sad Working on it ( i dont have photoshop)
   
   
This post was last modified: 10-30-2010, 09:37 PM by led-panzer.

1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
10-30-2010, 09:31 PM #3

Turns out the pictures are too big.Sad Working on it ( i dont have photoshop)


   
   


1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake

Captain America
Boostin' & Roostin'

2,221
10-30-2010, 09:37 PM #4
you have Microsoft office?

the Microsoft picture manager makes it easy to resize pics


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
10-30-2010, 09:37 PM #4

you have Microsoft office?

the Microsoft picture manager makes it easy to resize pics



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

led-panzer
Holset

541
10-30-2010, 09:44 PM #5
I figured it out
               
Lets Try Again
   
   
   
   
This post was last modified: 10-30-2010, 09:48 PM by led-panzer.

1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
10-30-2010, 09:44 PM #5

I figured it out
               


Lets Try Again
   
   
   
   


1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake

Captain America
Boostin' & Roostin'

2,221
10-30-2010, 09:51 PM #6
Why do I like the look with only headlights and nothing else????


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
10-30-2010, 09:51 PM #6

Why do I like the look with only headlights and nothing else????



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

JB3
Superturbo

1,795
10-30-2010, 09:55 PM #7
Welcome! Nice job on bringing the car back from that! Did you cut out and weld in a new piece, or were you able to bring the inner fender/headlight frame back?

I have a 300D the same color. I love it personally, I think it looks great on these cars

Are you staying with that color, or respraying the whole car?

1974 240D 617 turbo swap, W201 5-speed, in the works project
1983 240D 616 stock, DD
1989 Chevy Astro, 617 turbo swap, T5 5-speed, 4.56 diff, work van

JB3
10-30-2010, 09:55 PM #7

Welcome! Nice job on bringing the car back from that! Did you cut out and weld in a new piece, or were you able to bring the inner fender/headlight frame back?

I have a 300D the same color. I love it personally, I think it looks great on these cars

Are you staying with that color, or respraying the whole car?


1974 240D 617 turbo swap, W201 5-speed, in the works project
1983 240D 616 stock, DD
1989 Chevy Astro, 617 turbo swap, T5 5-speed, 4.56 diff, work van

led-panzer
Holset

541
10-30-2010, 09:56 PM #8
Im really looking like a noob here lol. The car was originally from california so its completely rust free, unfortunatly it has all that emmisions crap on it (evil trap ox) it has all the maintence records from 1985 to the present with everything being done at the dealership, including an $8200 bill for a new block, cylinder head, and radiator lol. Still has the stamped tag from the original owner, the seats have had covers on them since the day it was bought, not even a coffee stain. And it has the original med kit in the back, never used.
Eventually i will re spray the whole car, im keeping the original color. Yea i cut out a new bracket for the headlight on our cnc plasma cutter and welded it on.
This post was last modified: 10-30-2010, 09:58 PM by led-panzer.

1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
10-30-2010, 09:56 PM #8

Im really looking like a noob here lol. The car was originally from california so its completely rust free, unfortunatly it has all that emmisions crap on it (evil trap ox) it has all the maintence records from 1985 to the present with everything being done at the dealership, including an $8200 bill for a new block, cylinder head, and radiator lol. Still has the stamped tag from the original owner, the seats have had covers on them since the day it was bought, not even a coffee stain. And it has the original med kit in the back, never used.


Eventually i will re spray the whole car, im keeping the original color. Yea i cut out a new bracket for the headlight on our cnc plasma cutter and welded it on.


1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake

willbhere4u
Six in a row make her go!

2,507
10-30-2010, 11:10 PM #9
Looking good great job saving a great car from going to the crusher! I really like the wheels!

I went through almost the exact same stuff on my 300sdl but mine wasn't nearly this involved witch was good for me because I'm a novice compared to what you can do! I usually stick to mechanical fabricating not body work!


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
10-30-2010, 11:10 PM #9

Looking good great job saving a great car from going to the crusher! I really like the wheels!

I went through almost the exact same stuff on my 300sdl but mine wasn't nearly this involved witch was good for me because I'm a novice compared to what you can do! I usually stick to mechanical fabricating not body work!


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

led-panzer
Holset

541
10-31-2010, 10:38 AM #10
Thanks guys. I didn't plan on joining the forum for a little while, at least until I could actually add some performance goodies lol but there was an M pump for sale in the FS WTB section that I couldn't pass up and I had to join to get it. Next up after the paint and the windshield will be to get rid of the trap ox and put a real manifold on it, get a long runner intake manifold, and put a 3 inch turbo back exhaust, and pull the rack limiter. Oh and the gauges. Eventual plans are to put a gt2256v on it but I'm running out of money lol. Currently the odometer reads 275,000

1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
10-31-2010, 10:38 AM #10

Thanks guys. I didn't plan on joining the forum for a little while, at least until I could actually add some performance goodies lol but there was an M pump for sale in the FS WTB section that I couldn't pass up and I had to join to get it. Next up after the paint and the windshield will be to get rid of the trap ox and put a real manifold on it, get a long runner intake manifold, and put a 3 inch turbo back exhaust, and pull the rack limiter. Oh and the gauges. Eventual plans are to put a gt2256v on it but I'm running out of money lol. Currently the odometer reads 275,000


1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake

garage
Bush Taxi

893
10-31-2010, 12:51 PM #11
Welcome! Prepare to have a new addiction!!Big Grin
The trap ox really sucks to have.

Willbe, those wheels are really nice huh! I like them alot, it gives the car a more modern look.

Captian, i stared at the pic with no front body work for like 5mins hahah

1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
garage
10-31-2010, 12:51 PM #11

Welcome! Prepare to have a new addiction!!Big Grin
The trap ox really sucks to have.

Willbe, those wheels are really nice huh! I like them alot, it gives the car a more modern look.

Captian, i stared at the pic with no front body work for like 5mins hahah


1987 300D: EGR Delete, ARV Delete, Cold Air Intake...

DeliveryValve
Superturbo

1,338
10-31-2010, 03:14 PM #12
Nice job so far.

Welcome to becoming a member on this forum.



.

Gota love Mercedes Diesels!



.
DeliveryValve
10-31-2010, 03:14 PM #12

Nice job so far.

Welcome to becoming a member on this forum.



.


Gota love Mercedes Diesels!



.

Captain America
Boostin' & Roostin'

2,221
10-31-2010, 05:11 PM #13
yeah this is the one that caught my eye

   

I like the look without the headlight grill thingys

looks like some mad max shit
This post was last modified: 10-31-2010, 05:12 PM by Captain America.


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
10-31-2010, 05:11 PM #13

yeah this is the one that caught my eye

   

I like the look without the headlight grill thingys

looks like some mad max shit



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

led-panzer
Holset

541
10-31-2010, 06:32 PM #14
(10-31-2010, 05:11 PM)Captain America yeah this is the one that caught my eye



I like the look without the headlight grill thingys

looks like some mad max shit

Lol yea I needed to have the trim on them to help align the hood and fenders. Still here working on this thing, I wish I could say one part was worse than the other but it all sucks lol.


Murphys law. Just drove it around the parking lot before I went to go home and the fan hit the radiator which broke a blade and put a hole in the radiator. Fml.
This post was last modified: 10-31-2010, 07:12 PM by led-panzer.

1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
10-31-2010, 06:32 PM #14

(10-31-2010, 05:11 PM)Captain America yeah this is the one that caught my eye



I like the look without the headlight grill thingys

looks like some mad max shit

Lol yea I needed to have the trim on them to help align the hood and fenders. Still here working on this thing, I wish I could say one part was worse than the other but it all sucks lol.


Murphys law. Just drove it around the parking lot before I went to go home and the fan hit the radiator which broke a blade and put a hole in the radiator. Fml.


1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake

Captain America
Boostin' & Roostin'

2,221
10-31-2010, 09:14 PM #15
Awe man! Sorry to hear that. That sucks for sure. Now you need a fan and a radiator. Well it gives you the opportunity to get rid of that crap plastic radiator and get an all aluminum radiator that wont leak and break. Then just put an electric fan on it!


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
10-31-2010, 09:14 PM #15

Awe man! Sorry to hear that. That sucks for sure. Now you need a fan and a radiator. Well it gives you the opportunity to get rid of that crap plastic radiator and get an all aluminum radiator that wont leak and break. Then just put an electric fan on it!



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

led-panzer
Holset

541
11-01-2010, 11:13 AM #16
Well a little bit of good news, my friends dad is scrapping his 83 sd and I can have the radiator and fan for free. Wish the windshields were the same.....

1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
11-01-2010, 11:13 AM #16

Well a little bit of good news, my friends dad is scrapping his 83 sd and I can have the radiator and fan for free. Wish the windshields were the same.....


1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake

willbhere4u
Six in a row make her go!

2,507
11-01-2010, 02:05 PM #17
check them side by side I don't think that are the same but I could be wrong!

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
11-01-2010, 02:05 PM #17

check them side by side I don't think that are the same but I could be wrong!


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

led-panzer
Holset

541
12-04-2010, 08:36 PM #18
Radiator, fan, and windshield all installed, prepped for paint and ready to shoot Monday. I wanted to have this thing on the road before snow flew but it didn't turn out that way. It's going to be so nice to have a good vehicle this winter, last winter I drove an 89 jeep with no carpet or drain plugs and a top that didn't fit right, I would have to brush the snow off the drivers seat in the morning and snow would land on me at lights. Add that to the fact that it was a stick and a 4 banger with a cracked bell housing and it was a pretty shitty winter. Oh and no 4 wheel drive. To go from that to a Mercedes lol......

1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
12-04-2010, 08:36 PM #18

Radiator, fan, and windshield all installed, prepped for paint and ready to shoot Monday. I wanted to have this thing on the road before snow flew but it didn't turn out that way. It's going to be so nice to have a good vehicle this winter, last winter I drove an 89 jeep with no carpet or drain plugs and a top that didn't fit right, I would have to brush the snow off the drivers seat in the morning and snow would land on me at lights. Add that to the fact that it was a stick and a 4 banger with a cracked bell housing and it was a pretty shitty winter. Oh and no 4 wheel drive. To go from that to a Mercedes lol......


1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake

JB3
Superturbo

1,795
12-04-2010, 09:10 PM #19
a 2wd jeep? broken or stock? I though I was the only lunatic to own a 2wd jeep! Big Grin 1996 jeep cherokee, stock with 4cly, 2wd, 5 speed. Basically a high station wagon. I know how you feel! Nothing like driving something that can't do what its known for as a brand! Sold it after about a year of use

What other parts from that SD can you scrounge before it goes to the highway in the sky? Is the engine blown or anything? Id take tons of engine compartment stuff, even the whole drivetrain if given enough time to grab it
This post was last modified: 12-04-2010, 09:10 PM by JB3.

1974 240D 617 turbo swap, W201 5-speed, in the works project
1983 240D 616 stock, DD
1989 Chevy Astro, 617 turbo swap, T5 5-speed, 4.56 diff, work van

JB3
12-04-2010, 09:10 PM #19

a 2wd jeep? broken or stock? I though I was the only lunatic to own a 2wd jeep! Big Grin 1996 jeep cherokee, stock with 4cly, 2wd, 5 speed. Basically a high station wagon. I know how you feel! Nothing like driving something that can't do what its known for as a brand! Sold it after about a year of use

What other parts from that SD can you scrounge before it goes to the highway in the sky? Is the engine blown or anything? Id take tons of engine compartment stuff, even the whole drivetrain if given enough time to grab it


1974 240D 617 turbo swap, W201 5-speed, in the works project
1983 240D 616 stock, DD
1989 Chevy Astro, 617 turbo swap, T5 5-speed, 4.56 diff, work van

led-panzer
Holset

541
12-04-2010, 09:30 PM #20
The jeep was originally a 4x4 but it was broken. The computer took a dump for some reason in late may, a guy offered me 350 bucks for it as is and I took it. As far as the sd its long ogone, he wanted to get rid of it and only got like 200 bucks, it was worth twice that in scrap and way more if he parted it out but I guess he got what he wanted. He ran it on WVO which took its toll, its his third Benz to be killed by rust and veggie oil. After what he did and seeing what it did to my dads powerstroke that shit will never touch my tank. At least I got his valve cover and hood star Smile

1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
12-04-2010, 09:30 PM #20

The jeep was originally a 4x4 but it was broken. The computer took a dump for some reason in late may, a guy offered me 350 bucks for it as is and I took it. As far as the sd its long ogone, he wanted to get rid of it and only got like 200 bucks, it was worth twice that in scrap and way more if he parted it out but I guess he got what he wanted. He ran it on WVO which took its toll, its his third Benz to be killed by rust and veggie oil. After what he did and seeing what it did to my dads powerstroke that shit will never touch my tank. At least I got his valve cover and hood star Smile


1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake

led-panzer
Holset

541
12-13-2010, 08:47 PM #21
Its done Big Grin
   
   
   
   

1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
12-13-2010, 08:47 PM #21

Its done Big Grin
   
   
   
   


1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake

George3soccer
Holset

373
12-14-2010, 02:21 AM #22
Looks great, congrats on the job well done.

Mb 1984 w201 om603 swap.
Mb 1986 w201 190E 2.3-16v
Mb 2004 w203 C230k
George3soccer
12-14-2010, 02:21 AM #22

Looks great, congrats on the job well done.


Mb 1984 w201 om603 swap.
Mb 1986 w201 190E 2.3-16v
Mb 2004 w203 C230k

JB3
Superturbo

1,795
12-14-2010, 10:18 AM #23
yeah! good as new, great job! Maybe you can repaint the ass end of my car same color! Big Grin

1974 240D 617 turbo swap, W201 5-speed, in the works project
1983 240D 616 stock, DD
1989 Chevy Astro, 617 turbo swap, T5 5-speed, 4.56 diff, work van

JB3
12-14-2010, 10:18 AM #23

yeah! good as new, great job! Maybe you can repaint the ass end of my car same color! Big Grin


1974 240D 617 turbo swap, W201 5-speed, in the works project
1983 240D 616 stock, DD
1989 Chevy Astro, 617 turbo swap, T5 5-speed, 4.56 diff, work van

led-panzer
Holset

541
12-14-2010, 02:57 PM #24
I'm all out of paint or I would lol, two fenders the hood and the door took a whole quart of base and almost a quart of clear. My dad did the painting anyway I've never painted anything before. It figures the first two nights I get to drive it are huge snow storms but I must say I was very impressed, its quite a little tank in the snow. And thanks guys, its nice to hear the opinions of people who actually know what's involved in a project like this, not "So you just took the crushed parts off and put the new ones on?"

1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
12-14-2010, 02:57 PM #24

I'm all out of paint or I would lol, two fenders the hood and the door took a whole quart of base and almost a quart of clear. My dad did the painting anyway I've never painted anything before. It figures the first two nights I get to drive it are huge snow storms but I must say I was very impressed, its quite a little tank in the snow. And thanks guys, its nice to hear the opinions of people who actually know what's involved in a project like this, not "So you just took the crushed parts off and put the new ones on?"


1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake

Captain America
Boostin' & Roostin'

2,221
12-14-2010, 03:45 PM #25
Hey so you just took all the smashed shit off and put good parts on from another car that was the same color?

Haha. It looks real good though... can't even tell!


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
12-14-2010, 03:45 PM #25

Hey so you just took all the smashed shit off and put good parts on from another car that was the same color?

Haha. It looks real good though... can't even tell!



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

led-panzer
Holset

541
12-14-2010, 03:56 PM #26
Now its your turn captain, fix the ass end of that red beater lol

1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
12-14-2010, 03:56 PM #26

Now its your turn captain, fix the ass end of that red beater lol


1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake

willbhere4u
Six in a row make her go!

2,507
12-14-2010, 05:05 PM #27
Very impressive glad to see one saved from the crusher!

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
12-14-2010, 05:05 PM #27

Very impressive glad to see one saved from the crusher!


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

mike-81-240d
more like mike-84-300d now

427
12-14-2010, 08:13 PM #28
Very nice.

1981 Mercedes 300TD Lowered 4 speed manual Holset HX30 
mike-81-240d
12-14-2010, 08:13 PM #28

Very nice.


1981 Mercedes 300TD Lowered 4 speed manual Holset HX30 

300D50
Graphite Moderator, ala RBMK

775
12-15-2010, 01:08 AM #29
Looks awesome! No crush for you!Big Grin

(12-14-2010, 10:18 AM)dropnosky yeah! good as new, great job! Maybe you can repaint the ass end of my car same color! Big Grin

The MintyFreshMobile needs more than paint last I knew, or did things change?


1990 Power Ram 50 V6 SOHC 24V 6g72

I can be wrong, don't take everything I say as verbatim, please fact-check first.
My posts are my personal opinions and thoughts, unless otherwise noted.
300D50
12-15-2010, 01:08 AM #29

Looks awesome! No crush for you!Big Grin

(12-14-2010, 10:18 AM)dropnosky yeah! good as new, great job! Maybe you can repaint the ass end of my car same color! Big Grin

The MintyFreshMobile needs more than paint last I knew, or did things change?


1990 Power Ram 50 V6 SOHC 24V 6g72

I can be wrong, don't take everything I say as verbatim, please fact-check first.
My posts are my personal opinions and thoughts, unless otherwise noted.

Captain America
Boostin' & Roostin'

2,221
12-15-2010, 04:40 AM #30
(12-14-2010, 03:56 PM)led-panzer Now its your turn captain, fix the ass end of that red beater lol

Be my guest sir. I would like her to have some fresh skin but I have no desire to do the required body work... I'd rather pay to have someone do it for me


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
12-15-2010, 04:40 AM #30

(12-14-2010, 03:56 PM)led-panzer Now its your turn captain, fix the ass end of that red beater lol

Be my guest sir. I would like her to have some fresh skin but I have no desire to do the required body work... I'd rather pay to have someone do it for me



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

led-panzer
Holset

541
12-15-2010, 08:39 AM #31
(12-15-2010, 04:40 AM)Captain America
(12-14-2010, 03:56 PM)led-panzer Now its your turn captain, fix the ass end of that red beater lol

Be my guest sir. I would like her to have some fresh skin but I have no desire to do the required body work... I'd rather pay to have someone do it for me

I was Just messing with you cap. If I lived a little closer I would do it for you its not that bad when you dive into it but it will always look better when someone else does it, when you do it yourself you know where all the imperfections are.

1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
12-15-2010, 08:39 AM #31

(12-15-2010, 04:40 AM)Captain America
(12-14-2010, 03:56 PM)led-panzer Now its your turn captain, fix the ass end of that red beater lol

Be my guest sir. I would like her to have some fresh skin but I have no desire to do the required body work... I'd rather pay to have someone do it for me

I was Just messing with you cap. If I lived a little closer I would do it for you its not that bad when you dive into it but it will always look better when someone else does it, when you do it yourself you know where all the imperfections are.


1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake

Captain America
Boostin' & Roostin'

2,221
12-15-2010, 09:55 PM #32
Yeah I know lol. I forgot to add the "haha" to my response. I know exactly what your saying. Its really just something im not even close to being interested in doing. I can do ANYTHING else, but body and paint is not my thing. I give you mad props on the work you did man it looks fantastic in the pictures.


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
12-15-2010, 09:55 PM #32

Yeah I know lol. I forgot to add the "haha" to my response. I know exactly what your saying. Its really just something im not even close to being interested in doing. I can do ANYTHING else, but body and paint is not my thing. I give you mad props on the work you did man it looks fantastic in the pictures.



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

willbhere4u
Six in a row make her go!

2,507
12-15-2010, 10:08 PM #33
I think Cap should make a w123 El Camino

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
12-15-2010, 10:08 PM #33

I think Cap should make a w123 El Camino


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

Captain America
Boostin' & Roostin'

2,221
12-21-2010, 06:02 PM #34
^^^^^ Effffin Genius!


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
12-21-2010, 06:02 PM #34

^^^^^ Effffin Genius!



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

led-panzer
Holset

541
02-23-2011, 05:39 PM #35
Put my gauges in after staring at them every day for two months, surprisingly not that hard although I still have the stock manifolds on so ill have to drill and tap again. Took it out on the highway and was quite surprised - I'm getting about 22lbs of boost! And yes I know before someone hops on me that I don't need that much, I dunno if my wastegate is stuck closed or what but ill have to figure that one out. I still have yet to get rid of the EGR I don't know if that is contributing to the high boost or not. EGTs maxed out at just over 1000.

At least two glow plugs are bad, it shakes and rattles like hell on a cold startup so that's the next project. Already switched it to mobil1 5w-40, damn what an expensive oil change that was Big Grin

1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
02-23-2011, 05:39 PM #35

Put my gauges in after staring at them every day for two months, surprisingly not that hard although I still have the stock manifolds on so ill have to drill and tap again. Took it out on the highway and was quite surprised - I'm getting about 22lbs of boost! And yes I know before someone hops on me that I don't need that much, I dunno if my wastegate is stuck closed or what but ill have to figure that one out. I still have yet to get rid of the EGR I don't know if that is contributing to the high boost or not. EGTs maxed out at just over 1000.

At least two glow plugs are bad, it shakes and rattles like hell on a cold startup so that's the next project. Already switched it to mobil1 5w-40, damn what an expensive oil change that was Big Grin


1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake

led-panzer
Holset

541
02-27-2011, 08:44 PM #36
Removed all the EGR crap today.
   
Made my block off plate
   
Some improvement, but that could be in my head. Now Im getting this aweful low pitched whistling noise when i get over 5lbs of boost that, in my girlfriends words, sounds like Im dragging a cat. Sounds like its coming from the drivers side firewall. Its always something.

1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
02-27-2011, 08:44 PM #36

Removed all the EGR crap today.
   
Made my block off plate
   
Some improvement, but that could be in my head. Now Im getting this aweful low pitched whistling noise when i get over 5lbs of boost that, in my girlfriends words, sounds like Im dragging a cat. Sounds like its coming from the drivers side firewall. Its always something.


1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake

ForcedInduction
Banned

3,628
02-27-2011, 09:05 PM #37
Check that the turbine hasn't been damaged by the cat. Other than that, look for black soot streaks at joints and the manifold flanges.
This post was last modified: 02-27-2011, 09:05 PM by ForcedInduction.
ForcedInduction
02-27-2011, 09:05 PM #37

Check that the turbine hasn't been damaged by the cat. Other than that, look for black soot streaks at joints and the manifold flanges.

300D50
Graphite Moderator, ala RBMK

775
02-27-2011, 09:21 PM #38
(02-27-2011, 09:05 PM)ForcedInduction Check that the turbine hasn't been damaged by the cat.
Bwahahahaha, I don't have anything to say, except that's the funiest thing I've heard all day!
My mom had a woodchuck stuck in a serpentine belt once...



1990 Power Ram 50 V6 SOHC 24V 6g72

I can be wrong, don't take everything I say as verbatim, please fact-check first.
My posts are my personal opinions and thoughts, unless otherwise noted.
300D50
02-27-2011, 09:21 PM #38

(02-27-2011, 09:05 PM)ForcedInduction Check that the turbine hasn't been damaged by the cat.
Bwahahahaha, I don't have anything to say, except that's the funiest thing I've heard all day!
My mom had a woodchuck stuck in a serpentine belt once...



1990 Power Ram 50 V6 SOHC 24V 6g72

I can be wrong, don't take everything I say as verbatim, please fact-check first.
My posts are my personal opinions and thoughts, unless otherwise noted.

led-panzer
Holset

541
02-27-2011, 09:34 PM #39
Ah, you know it might be leaking around the little plate I made for the exhaust hole. Maybe ill double up or try some epoxy. Those manifolds will be replaced in time, I have to make the adaptor plate between the federal manifold and the vnt, clean up the w115 manifold, get a silicone boot, gaskets, and figure out the oil supply.

1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
02-27-2011, 09:34 PM #39

Ah, you know it might be leaking around the little plate I made for the exhaust hole. Maybe ill double up or try some epoxy. Those manifolds will be replaced in time, I have to make the adaptor plate between the federal manifold and the vnt, clean up the w115 manifold, get a silicone boot, gaskets, and figure out the oil supply.


1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake

led-panzer
Holset

541
03-06-2011, 11:41 PM #40
Sonafabitching alarm is going crazy it won't turn off except with the key in the door which, hey, I can't do while I'm driving so the whole way home the fucking alarm is blaring. I'll pull the relay or unplug it when I have light tomorrow. Damn.

1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
03-06-2011, 11:41 PM #40

Sonafabitching alarm is going crazy it won't turn off except with the key in the door which, hey, I can't do while I'm driving so the whole way home the fucking alarm is blaring. I'll pull the relay or unplug it when I have light tomorrow. Damn.


1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake

led-panzer
Holset

541
03-18-2011, 09:15 PM #41
Shined up the w115 manifold and sandblasted the exhaust manifold
   
The VNT arrived yesterday, a gt2056v from an '05(?) Liberty
   
Im opting to go with the opposing vacuum and pressure actuators, this seems the easiest form of control even though its not the best.

The stock bracket for the vacuum actuator wasnt big enough for the pressure actuator so i milled it out
       
I was able to cut the rod on the wastegate and cut the lever that came with it to make them work
   
Wastegate mounts right up
   
I made a cardboard template for the vacuum actuator, then measured everything and put it in the Plasmacam program, cut it out and bent it accordingly
   
   
Took a little bit of tweaking but everything mounted up right
   
   
I was able to get the studs out of the manifold before i left, ill knock out the adaptor between the turbo and manifold tommorow. The only things left are the silicone boot, oil supply lines, and making an exhaust for it.

1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
03-18-2011, 09:15 PM #41

Shined up the w115 manifold and sandblasted the exhaust manifold
   
The VNT arrived yesterday, a gt2056v from an '05(?) Liberty
   
Im opting to go with the opposing vacuum and pressure actuators, this seems the easiest form of control even though its not the best.

The stock bracket for the vacuum actuator wasnt big enough for the pressure actuator so i milled it out
       
I was able to cut the rod on the wastegate and cut the lever that came with it to make them work
   
Wastegate mounts right up
   
I made a cardboard template for the vacuum actuator, then measured everything and put it in the Plasmacam program, cut it out and bent it accordingly
   
   
Took a little bit of tweaking but everything mounted up right
   
   
I was able to get the studs out of the manifold before i left, ill knock out the adaptor between the turbo and manifold tommorow. The only things left are the silicone boot, oil supply lines, and making an exhaust for it.


1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake

willbhere4u
Six in a row make her go!

2,507
03-18-2011, 11:14 PM #42
looking good! That intake manifold looks tits!

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
03-18-2011, 11:14 PM #42

looking good! That intake manifold looks tits!


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

300D50
Graphite Moderator, ala RBMK

775
03-19-2011, 01:23 AM #43
Ohhh, you have cool toy!

CNC plasma is amazing for bracketry and other stuff, and you have such a large working area on sheet...


I'm green with envy.

And the turbo actuator and etc looks awesome as well!

1990 Power Ram 50 V6 SOHC 24V 6g72

I can be wrong, don't take everything I say as verbatim, please fact-check first.
My posts are my personal opinions and thoughts, unless otherwise noted.
300D50
03-19-2011, 01:23 AM #43

Ohhh, you have cool toy!

CNC plasma is amazing for bracketry and other stuff, and you have such a large working area on sheet...


I'm green with envy.

And the turbo actuator and etc looks awesome as well!


1990 Power Ram 50 V6 SOHC 24V 6g72

I can be wrong, don't take everything I say as verbatim, please fact-check first.
My posts are my personal opinions and thoughts, unless otherwise noted.

led-panzer
Holset

541
03-19-2011, 12:21 PM #44
Lol I only wish we could afford the equipment you have, I'm green with CNC envy Big Grin

Well its a good thing I mocked everything up, I was planning on making an adaptor .625 thick but the pressure actuator will hit the intake manifold. Solution - make the adaptor 2.00 thick. It's not ideal but it allows me to use both the actuators and the intake manifold.

1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
03-19-2011, 12:21 PM #44

Lol I only wish we could afford the equipment you have, I'm green with CNC envy Big Grin

Well its a good thing I mocked everything up, I was planning on making an adaptor .625 thick but the pressure actuator will hit the intake manifold. Solution - make the adaptor 2.00 thick. It's not ideal but it allows me to use both the actuators and the intake manifold.


1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake

Captain America
Boostin' & Roostin'

2,221
03-19-2011, 12:54 PM #45
(03-19-2011, 12:21 PM)led-panzer Lol I only wish we could afford the equipment you have, I'm green with CNC envy Big Grin

Well its a good thing I mocked everything up, I was planning on making an adaptor .625 thick but the pressure actuator will hit the intake manifold. Solution - make the adaptor 2.00 thick. It's not ideal but it allows me to use both the actuators and the intake manifold.

I am green with envy of both you fuckers!

Excuse the french!
This post was last modified: 03-19-2011, 12:54 PM by Captain America.
Captain America
03-19-2011, 12:54 PM #45

(03-19-2011, 12:21 PM)led-panzer Lol I only wish we could afford the equipment you have, I'm green with CNC envy Big Grin

Well its a good thing I mocked everything up, I was planning on making an adaptor .625 thick but the pressure actuator will hit the intake manifold. Solution - make the adaptor 2.00 thick. It's not ideal but it allows me to use both the actuators and the intake manifold.

I am green with envy of both you fuckers!

Excuse the french!

mike-81-240d
more like mike-84-300d now

427
03-21-2011, 12:34 AM #46
(03-19-2011, 12:54 PM)Captain America
(03-19-2011, 12:21 PM)led-panzer Lol I only wish we could afford the equipment you have, I'm green with CNC envy Big Grin

Well its a good thing I mocked everything up, I was planning on making an adaptor .625 thick but the pressure actuator will hit the intake manifold. Solution - make the adaptor 2.00 thick. It's not ideal but it allows me to use both the actuators and the intake manifold.

I am green with envy of both you fuckers!

My thoughts exactly...

1981 Mercedes 300TD Lowered 4 speed manual Holset HX30 
mike-81-240d
03-21-2011, 12:34 AM #46

(03-19-2011, 12:54 PM)Captain America
(03-19-2011, 12:21 PM)led-panzer Lol I only wish we could afford the equipment you have, I'm green with CNC envy Big Grin

Well its a good thing I mocked everything up, I was planning on making an adaptor .625 thick but the pressure actuator will hit the intake manifold. Solution - make the adaptor 2.00 thick. It's not ideal but it allows me to use both the actuators and the intake manifold.

I am green with envy of both you fuckers!

My thoughts exactly...


1981 Mercedes 300TD Lowered 4 speed manual Holset HX30 

led-panzer
Holset

541
03-28-2011, 09:10 PM #47
The center bearing on the driveshaft went on me, so what little time I had to devote to the turbo project is now being absorbed by fixing it. I was able to make a temporary fix with duct tape (gotta love the hillbilly tech my dad is full of them, like straightening the frame with a big steel bar, tow strap and his excursion). Ordered the part, but as long as I'm going to have the driveshaft out I may as well do the flex disks. Probably this weekend.

1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
03-28-2011, 09:10 PM #47

The center bearing on the driveshaft went on me, so what little time I had to devote to the turbo project is now being absorbed by fixing it. I was able to make a temporary fix with duct tape (gotta love the hillbilly tech my dad is full of them, like straightening the frame with a big steel bar, tow strap and his excursion). Ordered the part, but as long as I'm going to have the driveshaft out I may as well do the flex disks. Probably this weekend.


1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake

Captain America
Boostin' & Roostin'

2,221
03-29-2011, 01:24 AM #48
Haha Pulled a fender with a torch, ratchet strap and forklift once lol


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
03-29-2011, 01:24 AM #48

Haha Pulled a fender with a torch, ratchet strap and forklift once lol



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

winmutt
bitbanger

3,468
04-01-2011, 08:31 AM #49
(03-29-2011, 01:24 AM)Captain America Haha Pulled a fender with a torch, ratchet strap and forklift once lol

2 comealongs, 2 large trees and a dead blow hammed.

1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
winmutt
04-01-2011, 08:31 AM #49

(03-29-2011, 01:24 AM)Captain America Haha Pulled a fender with a torch, ratchet strap and forklift once lol

2 comealongs, 2 large trees and a dead blow hammed.


1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42

Captain America
Boostin' & Roostin'

2,221
04-01-2011, 06:14 PM #50
(04-01-2011, 08:31 AM)winmutt
(03-29-2011, 01:24 AM)Captain America Haha Pulled a fender with a torch, ratchet strap and forklift once lol

2 comealongs, 2 large trees and a dead blow hammed.

I was under the car putting the front suspension back together while the guy was doing the "bodywork"


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
04-01-2011, 06:14 PM #50

(04-01-2011, 08:31 AM)winmutt
(03-29-2011, 01:24 AM)Captain America Haha Pulled a fender with a torch, ratchet strap and forklift once lol

2 comealongs, 2 large trees and a dead blow hammed.

I was under the car putting the front suspension back together while the guy was doing the "bodywork"



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Pages (2): 1 2 Next
 
  • 3 Vote(s) - 3.67 Average
Users browsing this thread:
 14 Guest(s)
Users browsing this thread:
 14 Guest(s)