i belive its time to start a thread
i belive its time to start a thread
Hotrodbenz
05-17-2012, 06:43 PM #1so i bought my car alomost a year ago i drove it alot 100mi a day got awsome mileage also did some mods 3in exaust stock turbo boost cranked alda removed yeah i know no power gain but it was a blast blew the front pump seal and stumbled on a 126 with a 603 so the om603 and the 722.3 are going in my 123 hope it works also intercooling and removing the oxtrap water meth full cranked pump propane and im rebuilding the trans and cutting the springs
-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
05-17-2012, 08:13 PM #2That is a lot of stuff
-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
(05-17-2012, 06:43 PM)Hotrodbenz i believe its time to start a thread
Yes it is! Document everything... switching to that block opens up a lot of doors for newer transmissions as well... have you considered swapping in a manual?
W123 Mods: 4 speed ** manual climate control ** '85 Kalitucky intake ** manual windows & full tint ** Euro headlights retrofit w/bixenon projectors ** 4 brake light mod ** Vogtland 50mm drop front & Lesjofors S600 drop rear springs ** 16" rims ** late w126 brake spindles, rotors & calipers ** full suspension rehab ** Bilstein HDs ** AL129X alternator & 1/0 starter and charging cables ** 300GD clutch/flywheel ** AFCO 80103N radiator & Earl's 41610 oil cooler ** custom block-off plate, remote oil filter & t-stat ** MW IP w/ tomnik's 6.5mm 'Holly' elements **
S124 Mods: 400E Rear subframe ** SL600 Brakes ** Late 300E 210mm diff ** SLK230 6 speed ** 17" CLK rims ** Vented RF Fender ** Facelift Hood, Headlights, and Lower Cladding **
OBK# 62
SurfRodder
05-17-2012, 10:00 PM #3(05-17-2012, 06:43 PM)Hotrodbenz i believe its time to start a thread
Yes it is! Document everything... switching to that block opens up a lot of doors for newer transmissions as well... have you considered swapping in a manual?
W123 Mods: 4 speed ** manual climate control ** '85 Kalitucky intake ** manual windows & full tint ** Euro headlights retrofit w/bixenon projectors ** 4 brake light mod ** Vogtland 50mm drop front & Lesjofors S600 drop rear springs ** 16" rims ** late w126 brake spindles, rotors & calipers ** full suspension rehab ** Bilstein HDs ** AL129X alternator & 1/0 starter and charging cables ** 300GD clutch/flywheel ** AFCO 80103N radiator & Earl's 41610 oil cooler ** custom block-off plate, remote oil filter & t-stat ** MW IP w/ tomnik's 6.5mm 'Holly' elements **
S124 Mods: 400E Rear subframe ** SL600 Brakes ** Late 300E 210mm diff ** SLK230 6 speed ** 17" CLK rims ** Vented RF Fender ** Facelift Hood, Headlights, and Lower Cladding **
OBK# 62
by the way im 21 and work at auto zone part time 29+ hrs a week but it will move fast now that im home from school
Hotrodbenz
05-17-2012, 10:53 PM #4if i can find a manuel i would even with the mods im doing to the 722.3 i dont expect it to live key as to why im building it first trans gotta learn some how lol the biggest thing is i cant find one around here for a 603 i would love a 5 speed i could make a shifter work ive got a full fab shop in my shop but in oklahoma im having a hell of a time trying to find and afford a 5 speed or a 6 speed im fine with a 5 speed i can have a local shop build the clutch to hold the power and make the pressure plate clamp the biggest deal is finding the damn tranny theres tons of them way up north but they want 700 or more for the trans then id need slave master and pedal assy shifter fly wheel and much more i cant think of right off hand have the hx35 and the intercooler as whell as a 4in dp off my cummins have every thing for the propane and just got the snow kit ill take good pics with my iphone and keep you all posted now to learn to up load from my phone directly
by the way im 21 and work at auto zone part time 29+ hrs a week but it will move fast now that im home from school
(05-17-2012, 10:53 PM)Hotrodbenz by the way im 21 and work at auto zone part time 29+ hrs a week but it will move fast now that im home from school
That must be pretty sweeeeeet lol
-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
05-17-2012, 11:13 PM #5(05-17-2012, 10:53 PM)Hotrodbenz by the way im 21 and work at auto zone part time 29+ hrs a week but it will move fast now that im home from school
That must be pretty sweeeeeet lol
-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
Hotrodbenz
05-18-2012, 12:12 AM #6working for autozone has to be the worst job ever no one should have to sell auto parts in a red polo and slacks and the shit coustomers say like when they ask you a question and you give them an answer then they tell you your lying this is a common occurance ive been working on cars my whole life and been working in shops since i was 14 or so i know my shit any way....on the better note i did what i think may be a rebuild on a 722.325 or at least did a dry run with the parts on my table haha now i will tear it down and do it with all new parts i will post the web site im using for my assyembly help and im using a atgs sm way help full and didnt seem to hard once you learn the parts its a matter of sliding the one thing inside the other its like loosing you vcard all over again lol its elementry my dear watson haha
(05-18-2012, 12:12 AM)Hotrodbenz’' and didnt seem to hard once you learn the parts its a matter of sliding the one thing inside the other its like loosing you vcard all over again lol its elementry my dear watson haha
ahahahaha this shit is classic
if it don’t blow black...take it back.
1982 300TDT 4 Speed 196K Standard Beige “VEGEWGN”. 300GD FW. Walbro FRC-8 Fuel Pump. ZadaTech LCD Boost, EGT, & Fuel Pressure gauge. Non-EGR Exhaust and Intake Manifold. 3/2 Valves gone. Soon to have Elsbett WVO conversion
1981 300D 314K Midnight Blue “The Blue Car”, Lovecrap system, owned 25 years+
1985 300TD White 198K “Betty White” Pure beauty
The VEGEWGN
(05-18-2012, 12:12 AM)Hotrodbenz’' and didnt seem to hard once you learn the parts its a matter of sliding the one thing inside the other its like loosing you vcard all over again lol its elementry my dear watson haha
ahahahaha this shit is classic
if it don’t blow black...take it back.
1982 300TDT 4 Speed 196K Standard Beige “VEGEWGN”. 300GD FW. Walbro FRC-8 Fuel Pump. ZadaTech LCD Boost, EGT, & Fuel Pressure gauge. Non-EGR Exhaust and Intake Manifold. 3/2 Valves gone. Soon to have Elsbett WVO conversion
1981 300D 314K Midnight Blue “The Blue Car”, Lovecrap system, owned 25 years+
1985 300TD White 198K “Betty White” Pure beauty
The VEGEWGN
(05-18-2012, 12:12 AM)Hotrodbenz no one should have to sell auto parts in a red polo and slacks and the shit coustomers say...
I used to have to make and deliver pizzas in a red polo shirt and slacks, lol. Needless to say I bought the sturdiest most stain resistant slacks I could find, and somehow managed to keep them from getting too many sauce stains and what not on them
and the pizza place had 3 or 4 pot dispensaries within a mile of it, so yeah, people would come in and say allll kinds of crazy shit haha
-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
05-18-2012, 02:34 AM #8(05-18-2012, 12:12 AM)Hotrodbenz no one should have to sell auto parts in a red polo and slacks and the shit coustomers say...
I used to have to make and deliver pizzas in a red polo shirt and slacks, lol. Needless to say I bought the sturdiest most stain resistant slacks I could find, and somehow managed to keep them from getting too many sauce stains and what not on them
and the pizza place had 3 or 4 pot dispensaries within a mile of it, so yeah, people would come in and say allll kinds of crazy shit haha
-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
http://www.ganzeboom.net/images1/ganzebo...0722.4.pdf
This was a lot of help with all the gaskets and the small bearings and such
Hotrodbenz
05-18-2012, 08:15 AM #9Haha whell time to take a brake for the weekend I'll be outta town and work all day Sunday back on her Monday for a tear down and proper build also here's the link I us
http://www.ganzeboom.net/images1/ganzebo...0722.4.pdf
This was a lot of help with all the gaskets and the small bearings and such
Hotrodbenz
05-21-2012, 10:47 PM #10Well didn't work ony trans but did start pulling the om617 and trans should go quicker fr here on out any one know what the ECM did on the om603 and if I needed it cuz I didn't pull it or save the harness just hacked it in half and pulled the motor I've herd like idle control and shit but idk haven started my motor since pulling it as soon as I do get it in and the new exhausts manifold built I will be getting the twins built and installing my intercooler it sucks that there's no nice way to hide it but I'm going to try and tuck it in front of the radiatir or in the front lower valance and I want to build a front lip but don't know how it will look
Hotrodbenz
05-22-2012, 07:45 PM #14What's this a/c you Speke of... It's a race car not a cruiser roll down the windows
Hotrodbenz
05-22-2012, 10:06 PM #15Just when I was dreading the worst and fearing I would actually have to build this trans I found a whole 190e with a wait for it wait for it it's got a 5 speed haha I do however need 123 clutch and brake pedal assyembly and a 5 speed shifter would be nice but I can make the 201 shifter work I think
if it don’t blow black...take it back.
1982 300TDT 4 Speed 196K Standard Beige “VEGEWGN”. 300GD FW. Walbro FRC-8 Fuel Pump. ZadaTech LCD Boost, EGT, & Fuel Pressure gauge. Non-EGR Exhaust and Intake Manifold. 3/2 Valves gone. Soon to have Elsbett WVO conversion
1981 300D 314K Midnight Blue “The Blue Car”, Lovecrap system, owned 25 years+
1985 300TD White 198K “Betty White” Pure beauty
The VEGEWGN
Holla at me in a PM if you need a pedal assembly...
if it don’t blow black...take it back.
1982 300TDT 4 Speed 196K Standard Beige “VEGEWGN”. 300GD FW. Walbro FRC-8 Fuel Pump. ZadaTech LCD Boost, EGT, & Fuel Pressure gauge. Non-EGR Exhaust and Intake Manifold. 3/2 Valves gone. Soon to have Elsbett WVO conversion
1981 300D 314K Midnight Blue “The Blue Car”, Lovecrap system, owned 25 years+
1985 300TD White 198K “Betty White” Pure beauty
The VEGEWGN
(05-22-2012, 10:06 PM)Hotrodbenz Just when I was dreading the worst and fearing I would actually have to build this trans I found a whole 190e with a wait for it wait for it it's got a 5 speed haha I do however need 123 clutch and brake pedal assyembly and a 5 speed shifter would be nice but I can make the 201 shifter work I think
2 of the 201 shifter holes will line up and screw in stock, you will have to drill 2 holes for the other 2 bolts, otherwise it will work just fine on the 123 body.
Did you grab the shift gasket too? that will be needed also, the 123 one does not really work for this stick assembly
oh, and pics need to be added to this thread!
1974 240D 617 turbo swap, W201 5-speed, in the works project
1983 240D 616 stock, DD
1989 Chevy Astro, 617 turbo swap, T5 5-speed, 4.56 diff, work van
(05-22-2012, 10:06 PM)Hotrodbenz Just when I was dreading the worst and fearing I would actually have to build this trans I found a whole 190e with a wait for it wait for it it's got a 5 speed haha I do however need 123 clutch and brake pedal assyembly and a 5 speed shifter would be nice but I can make the 201 shifter work I think
2 of the 201 shifter holes will line up and screw in stock, you will have to drill 2 holes for the other 2 bolts, otherwise it will work just fine on the 123 body.
Did you grab the shift gasket too? that will be needed also, the 123 one does not really work for this stick assembly
oh, and pics need to be added to this thread!
1974 240D 617 turbo swap, W201 5-speed, in the works project
1983 240D 616 stock, DD
1989 Chevy Astro, 617 turbo swap, T5 5-speed, 4.56 diff, work van
1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
05-23-2012, 09:40 AM #18Is the starter on the correct side?
1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
Hotrodbenz
05-23-2012, 11:24 AM #19It's a 190e I got the whole car for 500 after finding a collector who is very interested in my project and at my age very impressed with my passion
Hotrodbenz
05-24-2012, 12:05 AM #20More good news today I found a 60 trim t3 from my mustang hiding in the bottom of a box along with a 50 trim both look massive next to my 45 trim on my om617 and tiny necpxt to my vt50 lol bad news was later to follow my horse was found in the woods bleeding profusely from a front and rear hoof so there will be a pause in the progress after the vet bill I haven't seen yet but I can't seem to think it will be cheap
I'll be following this quite close, plan a 606 into W123 (IF I ever get some spare cash!_)
Good news from Dropnosky on the W201 shifter and the W123 mounting-holes...
--So, Theoretically, I could get a rotten 2.5D 5-speed W201 with manual trans and just change the whole lot from engine back-plate rearwards into the W123, on the back of the 606....
Dunno at the mo just Where to get W126 engine-mount arms though--Not a particularly common car here anymore!....
![[Image: 300TDnoplate.jpg]](http://i190.photobucket.com/albums/z128/alastairhcii/300TDnoplate.jpg)
Alastair E
05-27-2012, 10:33 AM #21Well--Hope your horse hasnt suffered much and is OK now....
I'll be following this quite close, plan a 606 into W123 (IF I ever get some spare cash!_)
Good news from Dropnosky on the W201 shifter and the W123 mounting-holes...
--So, Theoretically, I could get a rotten 2.5D 5-speed W201 with manual trans and just change the whole lot from engine back-plate rearwards into the W123, on the back of the 606....
Dunno at the mo just Where to get W126 engine-mount arms though--Not a particularly common car here anymore!....
horse will be recovering after many many expences and plenty of time no rideing for me this summer
Hotrodbenz
05-27-2012, 11:00 AM #22the 603 came out of a ugly w126 so i go my arms with my motor witch rules
horse will be recovering after many many expences and plenty of time no rideing for me this summer
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
05-29-2012, 03:12 AM #23I'm confused... Where are the pictures?
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
(05-27-2012, 11:00 AM)Hotrodbenz horse will be recovering after many many expences and plenty of time no rideing for me this summer
If it wasnt for my horse, I wouldn't have spent that year in college...
W123 Mods: 4 speed ** manual climate control ** '85 Kalitucky intake ** manual windows & full tint ** Euro headlights retrofit w/bixenon projectors ** 4 brake light mod ** Vogtland 50mm drop front & Lesjofors S600 drop rear springs ** 16" rims ** late w126 brake spindles, rotors & calipers ** full suspension rehab ** Bilstein HDs ** AL129X alternator & 1/0 starter and charging cables ** 300GD clutch/flywheel ** AFCO 80103N radiator & Earl's 41610 oil cooler ** custom block-off plate, remote oil filter & t-stat ** MW IP w/ tomnik's 6.5mm 'Holly' elements **
S124 Mods: 400E Rear subframe ** SL600 Brakes ** Late 300E 210mm diff ** SLK230 6 speed ** 17" CLK rims ** Vented RF Fender ** Facelift Hood, Headlights, and Lower Cladding **
OBK# 62
SurfRodder
05-30-2012, 06:48 PM #24(05-27-2012, 11:00 AM)Hotrodbenz horse will be recovering after many many expences and plenty of time no rideing for me this summer
If it wasnt for my horse, I wouldn't have spent that year in college...
W123 Mods: 4 speed ** manual climate control ** '85 Kalitucky intake ** manual windows & full tint ** Euro headlights retrofit w/bixenon projectors ** 4 brake light mod ** Vogtland 50mm drop front & Lesjofors S600 drop rear springs ** 16" rims ** late w126 brake spindles, rotors & calipers ** full suspension rehab ** Bilstein HDs ** AL129X alternator & 1/0 starter and charging cables ** 300GD clutch/flywheel ** AFCO 80103N radiator & Earl's 41610 oil cooler ** custom block-off plate, remote oil filter & t-stat ** MW IP w/ tomnik's 6.5mm 'Holly' elements **
S124 Mods: 400E Rear subframe ** SL600 Brakes ** Late 300E 210mm diff ** SLK230 6 speed ** 17" CLK rims ** Vented RF Fender ** Facelift Hood, Headlights, and Lower Cladding **
OBK# 62
Hotrodbenz
06-04-2012, 02:49 PM #25Haha yeah sry guys new job had gotten in the way of the Benz then lost that so now I'm looking for a 8-5 job so I can kick autozone to the curb
1 Guest(s)
1 Guest(s)