STD Tuning Drivetrain Request: Measurement of 716.6xx 6 speed please

Request: Measurement of 716.6xx 6 speed please

Request: Measurement of 716.6xx 6 speed please

 
  • 0 Vote(s) - 0 Average
 
Grecy
GTA2056V

75
06-17-2014, 01:24 PM #1
Hi Everyone,

I'm looking at using a 716.6xx 6 speed behind an OM606 for a project, and I'd like a specific measurement please.

Please see the photo below - if anyone can measure length 'A' and 'B' please, that would be fantastic.
Basically, I'd like to know the overall length of the 716.6xx gearboxes, and the length of the front and rear halves of the gearbox casing.

   

Thanks,
-Dan
Grecy
06-17-2014, 01:24 PM #1

Hi Everyone,

I'm looking at using a 716.6xx 6 speed behind an OM606 for a project, and I'd like a specific measurement please.

Please see the photo below - if anyone can measure length 'A' and 'B' please, that would be fantastic.
Basically, I'd like to know the overall length of the 716.6xx gearboxes, and the length of the front and rear halves of the gearbox casing.

   

Thanks,
-Dan

pryantcc
TA 0301

63
06-18-2014, 09:48 AM #2
(06-17-2014, 01:24 PM)Grecy Hi Everyone,

I'm looking at using a 716.6xx 6 speed behind an OM606 for a project, and I'd like a specific measurement please.

Please see the photo below - if anyone can measure length 'A' and 'B' please, that would be fantastic.
Basically, I'd like to know the overall length of the 716.6xx gearboxes, and the length of the front and rear halves of the gearbox casing.



Thanks,
-Dan
A=298mm
B=160mm (to the outer edge of the seal on the gearbox output flange)

When I measured to the furthest point of the gearbox casing extrusion which is used to attach the gearbox rubber mount (the gearbox output shaft extends to approximately the same distance) the overall length of the gearbox is 525mm.

1992 W201 190D 2.0L and 1971 W108 280SE with OM606, electronic pump and 6 speed manual gearbox.
pryantcc
06-18-2014, 09:48 AM #2

(06-17-2014, 01:24 PM)Grecy Hi Everyone,

I'm looking at using a 716.6xx 6 speed behind an OM606 for a project, and I'd like a specific measurement please.

Please see the photo below - if anyone can measure length 'A' and 'B' please, that would be fantastic.
Basically, I'd like to know the overall length of the 716.6xx gearboxes, and the length of the front and rear halves of the gearbox casing.



Thanks,
-Dan
A=298mm
B=160mm (to the outer edge of the seal on the gearbox output flange)

When I measured to the furthest point of the gearbox casing extrusion which is used to attach the gearbox rubber mount (the gearbox output shaft extends to approximately the same distance) the overall length of the gearbox is 525mm.


1992 W201 190D 2.0L and 1971 W108 280SE with OM606, electronic pump and 6 speed manual gearbox.

Grecy
GTA2056V

75
06-18-2014, 11:04 AM #3
(06-18-2014, 09:48 AM)pryantcc A=298mm
B=160mm (to the outer edge of the seal on the gearbox output flange)

When I measured to the furthest point of the gearbox casing extrusion which is used to attach the gearbox rubber mount (the gearbox output shaft extends to approximately the same distance) the overall length of the gearbox is 525mm.

Thank you very much, that's extremely helpful!

-Dan
This post was last modified: 06-18-2014, 11:05 AM by Grecy.
Grecy
06-18-2014, 11:04 AM #3

(06-18-2014, 09:48 AM)pryantcc A=298mm
B=160mm (to the outer edge of the seal on the gearbox output flange)

When I measured to the furthest point of the gearbox casing extrusion which is used to attach the gearbox rubber mount (the gearbox output shaft extends to approximately the same distance) the overall length of the gearbox is 525mm.

Thank you very much, that's extremely helpful!

-Dan

 
  • 0 Vote(s) - 0 Average
Users browsing this thread:
 2 Guest(s)
Users browsing this thread:
 2 Guest(s)