OM602 Turbo Lag
OM602 Turbo Lag
10-19-2010, 01:32 PM
#2
1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
10-19-2010, 01:32 PM #2Being the 2.5 turbo I believe that the engine is actually om605?
1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
10-19-2010, 04:49 PM
#6
I also have a 190d 2.5turbo but I have messed up with IP, boost controller and LPG injection so boost increases much earlier and faster.
First thing you can do it reduce turbo lag is install a boost controller (~$10 on ebay). You may keep the stock boost pressure but lag will be reduced.
1992 Mercedes 190D 2.5 turbo 5sp manual. EGT+boost gauges. Boost controller set to ~14.5 psi. 1 1/4 turns on full load adjustment. LPG injection.
![[Image: 3803751914_8fdca63138_o.jpg]](http://farm4.static.flickr.com/3543/3803751914_8fdca63138_o.jpg)
Depends what gear you're in.
I also have a 190d 2.5turbo but I have messed up with IP, boost controller and LPG injection so boost increases much earlier and faster.
First thing you can do it reduce turbo lag is install a boost controller (~$10 on ebay). You may keep the stock boost pressure but lag will be reduced.
1992 Mercedes 190D 2.5 turbo 5sp manual. EGT+boost gauges. Boost controller set to ~14.5 psi. 1 1/4 turns on full load adjustment. LPG injection.
10-19-2010, 05:07 PM
#7
George3soccer
10-19-2010, 05:07 PM #7I do recommend, getting a few gauges, to aid in with the tunning on these OM motors.
10-19-2010, 05:20 PM
#8
I am planning on getting a boost controller but it should not reduce lag. If the stock wastegate is set to 12-13 psi it does not open until then, hence not bypassing any exhaust. I still have the Alda tamper seal on, I need to adjust it.
(10-19-2010, 05:07 PM)George3soccer I do recommend, getting a few gauges, to aid in with the tunning on these OM motors.
I have a boost gauge mounted under the radio. No egt gauge yet.
This post was last modified: 10-19-2010, 05:22 PM by BSharp.
1987 190DT
Under full throttle in 2nd or 3rd it does not reach full boost until 2700 rpm.
I am planning on getting a boost controller but it should not reduce lag. If the stock wastegate is set to 12-13 psi it does not open until then, hence not bypassing any exhaust. I still have the Alda tamper seal on, I need to adjust it.
(10-19-2010, 05:07 PM)George3soccer I do recommend, getting a few gauges, to aid in with the tunning on these OM motors.
I have a boost gauge mounted under the radio. No egt gauge yet.
1987 190DT
10-19-2010, 05:49 PM
#9
This post was last modified: 10-19-2010, 05:50 PM by willbhere4u.
1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
10-19-2010, 05:49 PM #9sorry I wasn't sure about the engine codes in the w201 I thought only the om605 was turbocharged
1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
10-19-2010, 06:17 PM
#10
(10-19-2010, 05:20 PM)BSharp Under full throttle in 2nd or 3rd it does not reach full boost until 2700 rpm.
I am planning on getting a boost controller but it should not reduce lag. If the stock wastegate is set to 12-13 psi it does not open until then,
As far as I know the wastegate is spring operated so it will start opening gradually until it reaches max aperture where it limits boost.
With a boost controller, the wastegate "doesn't see" boost until the boost controller tells it to. So if you dial the boost controller at about 11psi, the wastegate will start opening only at 11psi and not earlier.
1992 Mercedes 190D 2.5 turbo 5sp manual. EGT+boost gauges. Boost controller set to ~14.5 psi. 1 1/4 turns on full load adjustment. LPG injection.
(10-19-2010, 05:20 PM)BSharp Under full throttle in 2nd or 3rd it does not reach full boost until 2700 rpm.
I am planning on getting a boost controller but it should not reduce lag. If the stock wastegate is set to 12-13 psi it does not open until then,
As far as I know the wastegate is spring operated so it will start opening gradually until it reaches max aperture where it limits boost.
With a boost controller, the wastegate "doesn't see" boost until the boost controller tells it to. So if you dial the boost controller at about 11psi, the wastegate will start opening only at 11psi and not earlier.
1992 Mercedes 190D 2.5 turbo 5sp manual. EGT+boost gauges. Boost controller set to ~14.5 psi. 1 1/4 turns on full load adjustment. LPG injection.
Users browsing this thread:
11 Guest(s)
11 Guest(s)
Users browsing this thread:
11 Guest(s)
11 Guest(s)