IP timing, Myna 603 pump on 606 block??
IP timing, Myna 603 pump on 606 block??
when the tap is in the center of the inspection hole on the pump, and the crankshaft is at 15 degrees AFTER TDC (haynes manual), how many degrees BEFORE TDC starts the pump injection??
do i need special tools??
Diesel-Frank
08-23-2010, 09:13 AM #1hi! how to set the pumptiming on a om606, the pump is a myna from a om603 engine.
when the tap is in the center of the inspection hole on the pump, and the crankshaft is at 15 degrees AFTER TDC (haynes manual), how many degrees BEFORE TDC starts the pump injection??
do i need special tools??
I got the pump slid into the advance mechanism/gear/cog with some help from my dad to hold the cog engaged into the chain.I would like to find a way to now check the advance, but not sure how the spill port method works, I'm used to the Bosch VE 'Rear-entry' method and have dti and adapters for this.
hugh
I got mine fitted without special tools, I just set the engine 15 atdc (haynes manual here too) and with the notch held in the hole by a screwdriver I got the pump slid into the advance mechanism/gear/cog with some help from my dad to hold the cog engaged into the chain.
I would like to find a way to now check the advance, but not sure how the spill port method works, I'm used to the Bosch VE 'Rear-entry' method and have dti and adapters for this.
hugh
I plan to confirm this when I remove the electronic pump from my 606 I'll check its 'spill-timing' point before I remove it....
![[Image: 300TDnoplate.jpg]](http://i190.photobucket.com/albums/z128/alastairhcii/300TDnoplate.jpg)
Alastair E
08-23-2010, 10:02 AM #3I believe the spill timing is 24 degrees BTDC is equal to the pointer-in-line with governor housing at 15 degrees After TDC....
I plan to confirm this when I remove the electronic pump from my 606 I'll check its 'spill-timing' point before I remove it....
OM605 600hp diesel drag car build with BMW E30 chassis
Timing debend when that pump is made. Is that 7 or 8mm?
OM605 600hp diesel drag car build with BMW E30 chassis
--Not sure about the other guy...
Alastair E
08-23-2010, 04:58 PM #5I think HughF pump is still 5.5mm, He was testing out his 606 before getting pump modified...
--Not sure about the other guy...
(08-23-2010, 12:50 PM)jeemu Timing debend when that pump is made. Is that 7 or 8mm?
i think it is 7mm, but not sure. and they have changed to the newer cam, and external ALDA. myna told me the pump can handle 580hp on om606, and 510hp on om603
myna modified the pump for about a month ago.
Diesel-Frank
08-25-2010, 08:44 AM #7(08-23-2010, 12:50 PM)jeemu Timing debend when that pump is made. Is that 7 or 8mm?
i think it is 7mm, but not sure. and they have changed to the newer cam, and external ALDA. myna told me the pump can handle 580hp on om606, and 510hp on om603
myna modified the pump for about a month ago.
I have also new cam my ip.
tomnic: my friend can make what design cam you want.
OM605 600hp diesel drag car build with BMW E30 chassis
Like muuris say. Timing is 20 BTDC.
I have also new cam my ip.
tomnic: my friend can make what design cam you want.
OM605 600hp diesel drag car build with BMW E30 chassis
(08-25-2010, 01:49 PM)jeemu my friend can make what design cam you want.
first I should know what to change?
profile?
cam lift?
Next: still use the 7mm elements that originally are designed for 7mm cam lift?
Modification of the stock cam or completely new?
Tom
(08-25-2010, 02:04 PM)tomnikDont know about those cams. That i know at there is few desing of those.(08-25-2010, 01:49 PM)jeemu my friend can make what design cam you want.
first I should know what to change?
profile?
cam lift?
Next: still use the 7mm elements that originally are designed for 7mm cam lift?
Modification of the stock cam or completely new?
Tom
OM605 600hp diesel drag car build with BMW E30 chassis
(08-25-2010, 02:04 PM)tomnikDont know about those cams. That i know at there is few desing of those.(08-25-2010, 01:49 PM)jeemu my friend can make what design cam you want.
first I should know what to change?
profile?
cam lift?
Next: still use the 7mm elements that originally are designed for 7mm cam lift?
Modification of the stock cam or completely new?
Tom
OM605 600hp diesel drag car build with BMW E30 chassis
(08-25-2010, 09:52 AM)muuris As the pump is that new, set timing at the crank to 20 BTDC and install pump with the locking tool in the insp hole. Mynä changes the timing mark position inside the pump.
timing still is 24 deg but only the marks are changed?
jeemu: maybe you could measure the total cam lift next time when the delivery valves are out?
Tom
(08-25-2010, 09:52 AM)muuris As the pump is that new, set timing at the crank to 20 BTDC and install pump with the locking tool in the insp hole. Mynä changes the timing mark position inside the pump.
timing still is 24 deg but only the marks are changed?
jeemu: maybe you could measure the total cam lift next time when the delivery valves are out?
Tom
(08-26-2010, 06:21 AM)muuris I meant marks are changed from MB stock. I believe the actual injection timing is as the marks say. Haven't checked, though.
if timing mark now is 20 deg for BOD it's either because of increased pre lift adjustment or bigger supply bore or different position of supply bore compared to stock.
Nothing unusual using the 7mm elements.
But both increased bore and increased pre lift adjustments will reduce the effective stroke.
It gets interesting when the different position of the marks result from a different cam...
Tom
(08-26-2010, 06:21 AM)muuris I meant marks are changed from MB stock. I believe the actual injection timing is as the marks say. Haven't checked, though.
if timing mark now is 20 deg for BOD it's either because of increased pre lift adjustment or bigger supply bore or different position of supply bore compared to stock.
Nothing unusual using the 7mm elements.
But both increased bore and increased pre lift adjustments will reduce the effective stroke.
It gets interesting when the different position of the marks result from a different cam...
Tom
what size of the intercooler for the w124??
2,5 or 3" in/out??
height, width and thickness?
Diesel-Frank
08-29-2010, 07:49 AM #16thanks for good help! super forum!
what size of the intercooler for the w124??
2,5 or 3" in/out??
height, width and thickness?
I'm kinda confused. I have an om606 with a stock 603 IP, and I have got the timing screwed up. When I have the injection pump locking tool in, the engine should be at 24 BTDC? I was under the impression it was supposed to be 14 ATDC.
Help me, I need it!
Thanks in advance.
Hey guys,
I'm kinda confused. I have an om606 with a stock 603 IP, and I have got the timing screwed up. When I have the injection pump locking tool in, the engine should be at 24 BTDC? I was under the impression it was supposed to be 14 ATDC.
Help me, I need it!
Thanks in advance.
(08-25-2010, 09:52 AM)muuris As the pump is that new, set timing at the crank to 20 BTDC and install pump with the locking tool in the insp hole. Mynä changes the timing mark position inside the pump.
I believe only if you had Myna build the injection pump!
1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
10-29-2010, 11:19 AM #18(08-25-2010, 09:52 AM)muuris As the pump is that new, set timing at the crank to 20 BTDC and install pump with the locking tool in the insp hole. Mynä changes the timing mark position inside the pump.
I believe only if you had Myna build the injection pump!
1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
George3soccer
11-01-2010, 10:51 AM #21Where in Nj are you located? Also what chassis is this 606 in.
George3soccer
11-02-2010, 12:26 PM #23Nice nice. I have a few friends out in moristown, Jefferson, and Wharton.
18 Guest(s)
18 Guest(s)