Floyd-Suomi-pump
Floyd-Suomi-pump
603 turbo, mechanical IP, stock engine.
first the good news:
I sent a pump together with a set of Floyd elements and delivery valves to Finland. The pump was 3 days in the shop as the guy wanted to 'play' with the Floyd elements.
Yesterday I installed the pump and it ran perfectly form the first start without touching any adjustment, no return to idle issue, nothing, it just ran.
The short impression on the test drive was fast response, no idle smoke, perfect engine sound (timing, dynamically with clamp and strobe 24deg BTDC). This pump is noticeably stronger compared to the 7mm pump before.
Behaviour like stock, smooth power development (both pumps without turbo lag) but the Floyd pump gives the feeling of having lost the half of the weight of the car.
During hard acceleration I had acceptable smoke all the way up to approx. 150 Km/h (up to 5000/min), no black puff This is for sure adjustable as I did not touch anything before. The whole drive was about 15 min, 5-6 km.
Bad news:
Right after this acceleration the engine nailed terribly and smoked dark.
Back in my garage I checked the timing again because the nailing was combustion origin nothing mechanical (for my ears) so I checked the timing again. 36 degBTDC, which is the reason for nailing and smoke.
The IP did not move, no leaks, no grey/white smoke, no water/temperature/oil pressure issues, just about 12 deg advanced.
Can the timing device stuck in max. advanced position?
I'll check everything in the next couple of days..
Tom
Hi,
603 turbo, mechanical IP, stock engine.
first the good news:
I sent a pump together with a set of Floyd elements and delivery valves to Finland. The pump was 3 days in the shop as the guy wanted to 'play' with the Floyd elements.
Yesterday I installed the pump and it ran perfectly form the first start without touching any adjustment, no return to idle issue, nothing, it just ran.
The short impression on the test drive was fast response, no idle smoke, perfect engine sound (timing, dynamically with clamp and strobe 24deg BTDC). This pump is noticeably stronger compared to the 7mm pump before.
Behaviour like stock, smooth power development (both pumps without turbo lag) but the Floyd pump gives the feeling of having lost the half of the weight of the car.
During hard acceleration I had acceptable smoke all the way up to approx. 150 Km/h (up to 5000/min), no black puff This is for sure adjustable as I did not touch anything before. The whole drive was about 15 min, 5-6 km.
Bad news:
Right after this acceleration the engine nailed terribly and smoked dark.
Back in my garage I checked the timing again because the nailing was combustion origin nothing mechanical (for my ears) so I checked the timing again. 36 degBTDC, which is the reason for nailing and smoke.
The IP did not move, no leaks, no grey/white smoke, no water/temperature/oil pressure issues, just about 12 deg advanced.
Can the timing device stuck in max. advanced position?
I'll check everything in the next couple of days..
Tom
#20
ForcedInduction
03-06-2011, 05:04 AM
#2
12 degrees is beyond what the timer can adjust, but its also too little for a jumped chain tooth. The only other thing I can think of is the screw for individual element adjustment came loose.
#20
(03-06-2011, 05:04 AM)ForcedInduction 12 degrees is beyond what the timer can adjust, but its also too little for a jumped chain tooth. The only other thing I can think of is the screw for individual element adjustment came loose.
...but only on cyl. #1? If so the engine would shake but it does not, just nailing hard.
I'll check this by putting the clamp on the next cyl. to fire after #1 and check the deg in relation to TDC.
Thanks,
Tom
(03-06-2011, 05:04 AM)ForcedInduction 12 degrees is beyond what the timer can adjust, but its also too little for a jumped chain tooth. The only other thing I can think of is the screw for individual element adjustment came loose.
...but only on cyl. #1? If so the engine would shake but it does not, just nailing hard.
I'll check this by putting the clamp on the next cyl. to fire after #1 and check the deg in relation to TDC.
Thanks,
Tom
(03-07-2011, 12:58 AM)tomnikSo who or what company made it?(03-06-2011, 10:44 PM)jonbobshinigin Was this done at Myna?
No
OM605 600hp diesel drag car build with BMW E30 chassis
(03-07-2011, 12:58 AM)tomnikSo who or what company made it?(03-06-2011, 10:44 PM)jonbobshinigin Was this done at Myna?
No
OM605 600hp diesel drag car build with BMW E30 chassis
(03-07-2011, 05:09 PM)jeemu(03-07-2011, 12:58 AM)tomnikSo who or what company made it?(03-06-2011, 10:44 PM)jonbobshinigin Was this done at Myna?
No
There's others than Myna in Finland
- MB w126 300SD Superturbo (US) -83, Mods: OM617A with custom head work, Master Power Turbo 802332, PP-Diesel custom 7mm IP, China intercooler, KKD-Motorsport exhaust manifold, DIY intake manifold, Coolmist Waterinjection, DIY Supermeter display/datalog with PLX Wideband Lambda, Siekkinen custom 722.3 autotrans, Elbe Performance LSD, Green Filter cold air intake, straight 3" exhaust with two dual 2.5" outputs
- MB r129 500SL AMG (JDM) -94
Full AMG bodykit, full JDM features, modified ECU and exhaust
- MB w123 250E-TT (JDM) -85
Full 1JZ-GTE twinturbo conversion, full aircon, custom china cooler, custom IC-pipes, custom sport recaro interior, custom 3-piece JDM rims
(03-07-2011, 05:09 PM)jeemu(03-07-2011, 12:58 AM)tomnikSo who or what company made it?(03-06-2011, 10:44 PM)jonbobshinigin Was this done at Myna?
No
There's others than Myna in Finland
- MB w126 300SD Superturbo (US) -83, Mods: OM617A with custom head work, Master Power Turbo 802332, PP-Diesel custom 7mm IP, China intercooler, KKD-Motorsport exhaust manifold, DIY intake manifold, Coolmist Waterinjection, DIY Supermeter display/datalog with PLX Wideband Lambda, Siekkinen custom 722.3 autotrans, Elbe Performance LSD, Green Filter cold air intake, straight 3" exhaust with two dual 2.5" outputs
- MB r129 500SL AMG (JDM) -94
Full AMG bodykit, full JDM features, modified ECU and exhaust
- MB w123 250E-TT (JDM) -85
Full 1JZ-GTE twinturbo conversion, full aircon, custom china cooler, custom IC-pipes, custom sport recaro interior, custom 3-piece JDM rims
the reason for advanced jump of the pump is a defective toothed bushing in the timing device. Already the first time removing the pump I had issues to get it out. Installing was also critical being stupid I just pulled it into the timing device using the screw...
Funny thing is that this happened while deceleration otherwise the pump would have gone late.
Now I will install another timing device and continue the testing.
The pump was done by member pp d and it was the first pump which was really plug and run.
Tom
Hi,
the reason for advanced jump of the pump is a defective toothed bushing in the timing device. Already the first time removing the pump I had issues to get it out. Installing was also critical being stupid I just pulled it into the timing device using the screw...
Funny thing is that this happened while deceleration otherwise the pump would have gone late.
Now I will install another timing device and continue the testing.
The pump was done by member pp d and it was the first pump which was really plug and run.
Tom
(03-07-2011, 07:12 PM)JTYSome people here is no other place than Mynä(03-07-2011, 05:09 PM)jeemu(03-07-2011, 12:58 AM)tomnik NoSo who or what company made it?
There's others than Myna in Finland
OM605 600hp diesel drag car build with BMW E30 chassis
(03-07-2011, 07:12 PM)JTYSome people here is no other place than Mynä(03-07-2011, 05:09 PM)jeemu(03-07-2011, 12:58 AM)tomnik NoSo who or what company made it?
There's others than Myna in Finland
OM605 600hp diesel drag car build with BMW E30 chassis
(03-08-2011, 01:33 AM)jeemu(03-07-2011, 07:12 PM)JTY There's others than Myna in FinlandSome people here is no other place than Mynä
I know
PP-diesel is also okay, i have their IP in my anti superturbo 300SD and it has been working good from the start (several years now)
- MB w126 300SD Superturbo (US) -83, Mods: OM617A with custom head work, Master Power Turbo 802332, PP-Diesel custom 7mm IP, China intercooler, KKD-Motorsport exhaust manifold, DIY intake manifold, Coolmist Waterinjection, DIY Supermeter display/datalog with PLX Wideband Lambda, Siekkinen custom 722.3 autotrans, Elbe Performance LSD, Green Filter cold air intake, straight 3" exhaust with two dual 2.5" outputs
- MB r129 500SL AMG (JDM) -94
Full AMG bodykit, full JDM features, modified ECU and exhaust
- MB w123 250E-TT (JDM) -85
Full 1JZ-GTE twinturbo conversion, full aircon, custom china cooler, custom IC-pipes, custom sport recaro interior, custom 3-piece JDM rims
(03-08-2011, 01:33 AM)jeemu(03-07-2011, 07:12 PM)JTY There's others than Myna in FinlandSome people here is no other place than Mynä
I know
PP-diesel is also okay, i have their IP in my anti superturbo 300SD and it has been working good from the start (several years now)
- MB w126 300SD Superturbo (US) -83, Mods: OM617A with custom head work, Master Power Turbo 802332, PP-Diesel custom 7mm IP, China intercooler, KKD-Motorsport exhaust manifold, DIY intake manifold, Coolmist Waterinjection, DIY Supermeter display/datalog with PLX Wideband Lambda, Siekkinen custom 722.3 autotrans, Elbe Performance LSD, Green Filter cold air intake, straight 3" exhaust with two dual 2.5" outputs
- MB r129 500SL AMG (JDM) -94
Full AMG bodykit, full JDM features, modified ECU and exhaust
- MB w123 250E-TT (JDM) -85
Full 1JZ-GTE twinturbo conversion, full aircon, custom china cooler, custom IC-pipes, custom sport recaro interior, custom 3-piece JDM rims
1990 Power Ram 50 V6 SOHC 24V 6g72
I can be wrong, don't take everything I say as verbatim, please fact-check first.
My posts are my personal opinions and thoughts, unless otherwise noted.
We'd know there were places other than Myna if you guys didn't always say "go to Myna, they're the best, nobody else can do it"
1990 Power Ram 50 V6 SOHC 24V 6g72
I can be wrong, don't take everything I say as verbatim, please fact-check first.
My posts are my personal opinions and thoughts, unless otherwise noted.
(03-08-2011, 12:48 PM)300D50 We'd know there were places other than Myna if you guys didn't always say "go to Myna, they're the best, nobody else can do it"Huh huh
Of cource there is other good pump shops. Mynä just is the best here in Finland.
OM605 600hp diesel drag car build with BMW E30 chassis
(03-08-2011, 12:48 PM)300D50 We'd know there were places other than Myna if you guys didn't always say "go to Myna, they're the best, nobody else can do it"Huh huh
Of cource there is other good pump shops. Mynä just is the best here in Finland.
OM605 600hp diesel drag car build with BMW E30 chassis
6 Guest(s)
6 Guest(s)