Project Ingrid 1980 300SD
Project Ingrid 1980 300SD
02-27-2011, 03:44 PM
#1
Its an addiction.....She has 194,194miles on the odometer and runs pretty sweet, besides the large amount of grey smoke it produces when accelerating and a pretty bad oil leak(im REALLY hoping its not the rear seal).
Ill take it day by day with her and get her up to good operating condition. First things first it needs some glow plugs asap.
Unfortunetly the body has some rust here and there, especially along the bottom of the rear windshield, and a few small dents..no biggie.
The interior isnt too awful, ive driven in worse.
I havnt done anything to her besides removing the lower foglights, mounting the roofrack for my kayak, and cutting off the muffler, havnt even washed her yet.
![[Image: davidscarpictures053.jpg]](http://i857.photobucket.com/albums/ab131/carolambler/davidscarpictures053.jpg)
![[Image: davidscarpictures050.jpg]](http://i857.photobucket.com/albums/ab131/carolambler/davidscarpictures050.jpg)
![[Image: davidscarpictures048.jpg]](http://i857.photobucket.com/albums/ab131/carolambler/davidscarpictures048.jpg)
![[Image: davidscarpictures049.jpg]](http://i857.photobucket.com/albums/ab131/carolambler/davidscarpictures049.jpg)
![[Image: davidscarpictures051.jpg]](http://i857.photobucket.com/albums/ab131/carolambler/davidscarpictures051.jpg)
Damn rust....
![[Image: davidscarpictures052.jpg]](http://i857.photobucket.com/albums/ab131/carolambler/davidscarpictures052.jpg)
This post was last modified: 02-28-2011, 10:58 AM by garage.
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
This thread is to keep track of my newly purchased SD, Ingrid. This will be my 5th Mercedes diesel, and my 3rd SD Its an addiction.....
She has 194,194miles on the odometer and runs pretty sweet, besides the large amount of grey smoke it produces when accelerating and a pretty bad oil leak(im REALLY hoping its not the rear seal).
Ill take it day by day with her and get her up to good operating condition. First things first it needs some glow plugs asap.
Unfortunetly the body has some rust here and there, especially along the bottom of the rear windshield, and a few small dents..no biggie.
The interior isnt too awful, ive driven in worse.
I havnt done anything to her besides removing the lower foglights, mounting the roofrack for my kayak, and cutting off the muffler, havnt even washed her yet.
Damn rust....
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
02-27-2011, 06:44 PM
#3
(02-27-2011, 04:50 PM)Jtn190D Looks nice Its strange to see rust from SoCal. Did it come from the North?
It will do
Yeah rust in socal is purrty rare, but this car lived most of its life near the beach..so that explains alot of it
This post was last modified: 02-27-2011, 09:03 PM by garage.
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
02-28-2011, 11:01 AM
#4
See if i cant grab a 15inch wheel to replace that bundt with.
Does this car look like its been lowered already? Or is it just the 15inch wheels playing tricks on me?
__________________________________
Back from ecology, no wheels but i got 6 glow plugs and a trunk lid for my dad w126
This post was last modified: 02-28-2011, 03:40 PM by garage.
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
Goin to the junkyard this mornin, i havnt been in a few months.
See if i cant grab a 15inch wheel to replace that bundt with.
Does this car look like its been lowered already? Or is it just the 15inch wheels playing tricks on me?
__________________________________
Back from ecology, no wheels but i got 6 glow plugs and a trunk lid for my dad w126
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
02-28-2011, 04:47 PM
#5
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
02-28-2011, 04:47 PM #5Grey smoke means retarded IP timing! I know!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
02-28-2011, 05:56 PM
#6
(02-28-2011, 04:47 PM)Captain America Grey smoke means retarded IP timing! I know!
Well were gonna need to fix that shieet! I know it aint good thats for sure.
Just checked with AAA and theres $311 in registration fees..
Wish i woulda checked before i bought her, oh well.
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
(02-28-2011, 04:47 PM)Captain America Grey smoke means retarded IP timing! I know!
Well were gonna need to fix that shieet! I know it aint good thats for sure.
Just checked with AAA and theres $311 in registration fees..
Wish i woulda checked before i bought her, oh well.
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
02-28-2011, 11:11 PM
#7
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
02-28-2011, 11:11 PM #7Just need a 14, 27?mm and breaker bar for the IP bolts and crank bolt. We'll have her timed in no time! Haha
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
03-01-2011, 10:02 AM
#8
(02-28-2011, 11:11 PM)Captain America Just need a 14, 27?mm and breaker bar for the IP bolts and crank bolt. We'll have her timed in no time! Haha
Sweeeet, i belive i have all that already, i will double check and make sure.
Checked all my GPs and only one was bad so i replaced that with a top of the line junkyard model hahah.
Cleaned out the banjo going into the intake manifold, it was pretty sooty, but nothing horrific. Also cleaned out the banjo going into the ALDA and the lines goin into the overboost protection.
How important is it to have the overboost connected? Do you guys know of any engine failures that came from the overboost being bypassed?
Ive fucked with the ALDA before on previous cars, and ADA too, but each time the cap was already removed from it, this car still has the cap on..what is the safest way to remove the cap?
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
(02-28-2011, 11:11 PM)Captain America Just need a 14, 27?mm and breaker bar for the IP bolts and crank bolt. We'll have her timed in no time! Haha
Sweeeet, i belive i have all that already, i will double check and make sure.
Checked all my GPs and only one was bad so i replaced that with a top of the line junkyard model hahah.
Cleaned out the banjo going into the intake manifold, it was pretty sooty, but nothing horrific. Also cleaned out the banjo going into the ALDA and the lines goin into the overboost protection.
How important is it to have the overboost connected? Do you guys know of any engine failures that came from the overboost being bypassed?
Ive fucked with the ALDA before on previous cars, and ADA too, but each time the cap was already removed from it, this car still has the cap on..what is the safest way to remove the cap?
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
03-01-2011, 04:21 PM
#9
Just rip the cap off! haha
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
03-01-2011, 04:21 PM #9Well If you have a boost gauge then you really don't need the over boost protection... If you don't have a gauge then I'd keep it as it wont let boost go above 16lbs.
Just rip the cap off! haha
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
03-01-2011, 05:24 PM
#10
I made a REAL BONE HEAD move today.
This morning i took of the the injector lines so i can test a GP i was having doubts about. And when i was screwing the lines back on i accidently cross threaded the nut that screws onto the injection pump..
I feel like a total doofus doing somthing so ridiculous.
So the part that the nut screws on, on the IP is fucked.
If i take that off to replace it, that means i need to have the pump put on a bench to get it to run right again..right? I belive sitting right below that is the delivery valve, so id be screwing with that wich i know isnt good.
Im real bummed right now!
This post was last modified: 03-01-2011, 10:22 PM by garage.
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
Okay i will leave it alone for the time being then.
I made a REAL BONE HEAD move today.
This morning i took of the the injector lines so i can test a GP i was having doubts about. And when i was screwing the lines back on i accidently cross threaded the nut that screws onto the injection pump..
I feel like a total doofus doing somthing so ridiculous.
So the part that the nut screws on, on the IP is fucked.
If i take that off to replace it, that means i need to have the pump put on a bench to get it to run right again..right? I belive sitting right below that is the delivery valve, so id be screwing with that wich i know isnt good.
Im real bummed right now!
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
03-02-2011, 12:10 AM
#11
You can remove the piece that the injector line screws onto! You have to remove it and remove the delivery valve when you time the IP. Your good dude. 
Just stop by the junk yard and grab a new one!!!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
03-02-2011, 12:10 AM #11No no no! You can remove the piece that the injector line screws onto! You have to remove it and remove the delivery valve when you time the IP. Your good dude. Just stop by the junk yard and grab a new one!!!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
03-02-2011, 10:13 AM
#12
(03-02-2011, 12:10 AM)Captain America No no no!
Thats a sigh of relief! I wasnt too sure but i thought that piece didnt come off very simply.
Im glad its just as easy as a junk yard run!
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
(03-02-2011, 12:10 AM)Captain America No no no!
Thats a sigh of relief! I wasnt too sure but i thought that piece didnt come off very simply.
Im glad its just as easy as a junk yard run!
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
03-02-2011, 05:05 PM
#13
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
03-02-2011, 05:05 PM #13Yeah just done loosen the two nuts that are next to it! Those are the ones that cannot be touched IIRC
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
03-14-2011, 07:40 PM
#14
I disconnected the EGR and all related vacume hoses wich seemed to help out on the amount of grey smoke.
I also turned the ALDA all the way out, wich made a slight difference and made the turbo spool up a tad quicker.
Ill get some video up when i get some good tires on her.
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
Sweet, got her all fixed up.
I disconnected the EGR and all related vacume hoses wich seemed to help out on the amount of grey smoke.
I also turned the ALDA all the way out, wich made a slight difference and made the turbo spool up a tad quicker.
Ill get some video up when i get some good tires on her.
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
03-14-2011, 09:14 PM
#15
1981 300SD 230k miles "Gently Modified" Daily Driver
1999 F-250 7.3L Power Stroke 150k miles "The Usual Mods" Tow Rig
1981 300SD 190k miles "Heavily Modified"
GONE
DrewGerhan
03-14-2011, 09:14 PM #15I thought w116 SDs didnt have EGR?
1981 300SD 230k miles "Gently Modified" Daily Driver
1999 F-250 7.3L Power Stroke 150k miles "The Usual Mods" Tow Rig
1981 300SD 190k miles "Heavily Modified"
GONE
03-14-2011, 09:56 PM
#16
(03-14-2011, 09:14 PM)DrewGerhan I thought w116 SDs didnt have EGR?
Only in 78 and 79.
ForcedInduction
03-14-2011, 09:56 PM
#16
(03-14-2011, 09:14 PM)DrewGerhan I thought w116 SDs didnt have EGR?
Only in 78 and 79.
03-14-2011, 11:59 PM
#17
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
03-14-2011, 11:59 PM #17Now take the ALDA off more max fuel and burnouts!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
03-15-2011, 12:13 AM
#18
ForcedInduction
03-15-2011, 12:13 AM
#18
Not really, only smoke. The ALDA has no effect on power when correctly adjusted.
03-15-2011, 12:18 AM
#19
But in all seriousness,
No ALDA on the '81, almost no smoke, Night and day difference in acceleration off the line
Maybe the smoke is so little because I haven't done anything inside the pump yet?
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
03-15-2011, 12:18 AM #19That was mostly a sarcastic exaggeration
But in all seriousness,
No ALDA on the '81, almost no smoke, Night and day difference in acceleration off the line
Maybe the smoke is so little because I haven't done anything inside the pump yet?
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
03-15-2011, 10:08 AM
#21
(03-15-2011, 09:58 AM)garage ALDA will probably come off when i get some other things situated.
Capt, i bet she it starts smokin once you take the rack limiter out
I cant wait to take mine out!!
Yeah dude, I still need to do that. She's beggin for more fuel!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
03-15-2011, 10:08 AM #21(03-15-2011, 09:58 AM)garage ALDA will probably come off when i get some other things situated.
Capt, i bet she it starts smokin once you take the rack limiter out
I cant wait to take mine out!!
Yeah dude, I still need to do that. She's beggin for more fuel!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
03-15-2011, 02:53 PM
#23
-Jesse
80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon
10 mistsubishi fuso service truck.
My rack limiter didn't do much at all.
-Jesse
80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon
10 mistsubishi fuso service truck.
03-15-2011, 03:06 PM
#25
(03-15-2011, 03:01 PM)garage Did you notice anything from the full load screw?
The rack limiter is the full load adjustment.
ForcedInduction
03-15-2011, 03:06 PM
#25
(03-15-2011, 03:01 PM)garage Did you notice anything from the full load screw?
The rack limiter is the full load adjustment.
03-15-2011, 03:18 PM
#26
1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
03-15-2011, 03:18 PM #26I believe that's what he calls the torque control capsule
1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
03-15-2011, 03:28 PM
#27
-Jesse
80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon
10 mistsubishi fuso service truck.
The torque control is where I noticed the fuel/ power.
-Jesse
80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon
10 mistsubishi fuso service truck.
03-15-2011, 03:29 PM
#28
Sorry guess that was a troll move. I apologize.
I plan to follow the settings I saw on Brabus' thread
This post was last modified: 03-15-2011, 03:30 PM by Captain America.
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
03-15-2011, 03:29 PM #28Just max it all out!
Sorry guess that was a troll move. I apologize.
I plan to follow the settings I saw on Brabus' thread
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
03-15-2011, 08:58 PM
#29
To those reading later, torque control should not be touched. It will cause the engine to not return to idle and not cutoff fuel on deceleration.
ForcedInduction
03-15-2011, 08:58 PM
#29
All torque control will do is alter the rpm where the fuel starts to get cutoff. It doesn't alter maximum power.
To those reading later, torque control should not be touched. It will cause the engine to not return to idle and not cutoff fuel on deceleration.
03-16-2011, 09:59 AM
#30
So i took out the cruise control, and took off the trim below the taillights and headlights(looks 20x better without the trim)
Now theres going to be a few small holes in the body that are going to need to be filled so i dont get excess moisture in the trunk, so my question is, what brand of body filler should i go with on this??
Ive never done any proper body work, and im not looking for a showroom finish by any means. I bought the car mostly for its engine not its rust riddled body. The only reason im not going to weld them shut, is i just dont care enough about this car to invest that much in its body..rather put money and time into the engine.
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
Torque control screw was what i was reffering too, but i was just asking dieselboy according to his signature.
So i took out the cruise control, and took off the trim below the taillights and headlights(looks 20x better without the trim)
Now theres going to be a few small holes in the body that are going to need to be filled so i dont get excess moisture in the trunk, so my question is, what brand of body filler should i go with on this??
Ive never done any proper body work, and im not looking for a showroom finish by any means. I bought the car mostly for its engine not its rust riddled body. The only reason im not going to weld them shut, is i just dont care enough about this car to invest that much in its body..rather put money and time into the engine.
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
03-23-2011, 11:21 PM
#31
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
03-23-2011, 11:21 PM #31Dude, When are we going to have an SD drag race??
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
03-24-2011, 12:18 AM
#32
(03-23-2011, 11:21 PM)Captain America Dude, When are we going to have an SD drag race??
OHHH the w126 vs w116 battle royale
Is this drag race gonna be on asphalt or dirt..hmmm
Well i needa get some darn tires and redo the brakes, then i can start working on trying to get some power.
How many cases of beer do i need to buy to convince you to help me turn up my IP??
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
(03-23-2011, 11:21 PM)Captain America Dude, When are we going to have an SD drag race??
OHHH the w126 vs w116 battle royale
Is this drag race gonna be on asphalt or dirt..hmmm
Well i needa get some darn tires and redo the brakes, then i can start working on trying to get some power.
How many cases of beer do i need to buy to convince you to help me turn up my IP??
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
03-24-2011, 12:39 AM
#33
I'll race you on either dirt or road haha, Madd dirt burnouts!
You dont need brakes, The front end of my 126 feels like its gonna come apart when I apply the brakes haha
No beer needed. I'll help a buddy for free
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
03-24-2011, 12:39 AM #33Battle fuckin Royal for sure! Lets do it!!!
I'll race you on either dirt or road haha, Madd dirt burnouts!
You dont need brakes, The front end of my 126 feels like its gonna come apart when I apply the brakes haha
No beer needed. I'll help a buddy for free
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
03-24-2011, 09:28 AM
#34
Ha, yeah the front end of this car is pretty shakey when i brake above 50ish. But i have a sticky rear caliper, so i know thats robbing me of power.
Thanks Capt! When we get rid of this gloomy weather imm take you up on it for sure man!
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
Well then i im pretty sure this challange has to take place on both!
Ha, yeah the front end of this car is pretty shakey when i brake above 50ish. But i have a sticky rear caliper, so i know thats robbing me of power.
Thanks Capt! When we get rid of this gloomy weather imm take you up on it for sure man!
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
03-24-2011, 10:45 PM
#35
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
03-24-2011, 10:45 PM #35Cool dude. Just hit me up. You still have my number right?
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
03-24-2011, 11:00 PM
#36
So today i took ol' Ingrid to a dollar carwash down the road to try an get some grease off from the undercarriage, so i used my trusty mercedes jack to lift up the front passenger side of my car so i could squirt her off with degreaser. As im cranking the jack up, i hear some cracking and i find out this car has even worse rust than i thought.
The hole that the jack goes into rusted out...
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
I belive i do.
So today i took ol' Ingrid to a dollar carwash down the road to try an get some grease off from the undercarriage, so i used my trusty mercedes jack to lift up the front passenger side of my car so i could squirt her off with degreaser. As im cranking the jack up, i hear some cracking and i find out this car has even worse rust than i thought.
The hole that the jack goes into rusted out...
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
03-24-2011, 11:02 PM
#37
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
03-24-2011, 11:02 PM #37Oh no! Come cut the jack holes out of the blue car haha
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
![[Image: davidscarpictures055.jpg]](http://i857.photobucket.com/albums/ab131/carolambler/davidscarpictures055.jpg)
![[Image: davidscarpictures054.jpg]](http://i857.photobucket.com/albums/ab131/carolambler/davidscarpictures054.jpg)
03-26-2011, 02:31 PM
#40
The headlights on these cars looks so weird to me
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
03-26-2011, 02:31 PM #40Nice.
The headlights on these cars looks so weird to me
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
03-26-2011, 03:03 PM
#42
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
03-26-2011, 03:03 PM #42thats what I meant but didnt wanna say it haha
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
![[Image: davidscarpictures059.jpg]](http://i857.photobucket.com/albums/ab131/carolambler/davidscarpictures059.jpg)
03-26-2011, 10:22 PM
#44
Other than that, the black-out looks good.
1990 Power Ram 50 V6 SOHC 24V 6g72
I can be wrong, don't take everything I say as verbatim, please fact-check first.
My posts are my personal opinions and thoughts, unless otherwise noted.
Where the bleep is the star in the hood ornament??!
Other than that, the black-out looks good.
1990 Power Ram 50 V6 SOHC 24V 6g72
I can be wrong, don't take everything I say as verbatim, please fact-check first.
My posts are my personal opinions and thoughts, unless otherwise noted.
03-26-2011, 11:48 PM
#45
but im not sure yet. I will probably put the star back up oneday.I think i need to get a pair of yellow headlights from a w123...
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
It didnt come with one, i was thinking bout puttin some crosshairs up there but im not sure yet. I will probably put the star back up oneday.
I think i need to get a pair of yellow headlights from a w123...
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
03-27-2011, 04:39 PM
#46
I have a buddy that welded up a nut on the hood side and can cut me whatever logo I want on his CNC plasma table... Then just weld a stud to the bottom and bam you have any logo any size you want!
This post was last modified: 03-31-2011, 11:45 PM by Captain America.
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
03-27-2011, 04:39 PM #46Haha the star fell out of my maroon car too!
I have a buddy that welded up a nut on the hood side and can cut me whatever logo I want on his CNC plasma table... Then just weld a stud to the bottom and bam you have any logo any size you want!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
![[Image: davidscarpictures.jpg]](http://i857.photobucket.com/albums/ab131/carolambler/davidscarpictures.jpg)
![[Image: davidscarpictures071.jpg]](http://i857.photobucket.com/albums/ab131/carolambler/davidscarpictures071.jpg)
![[Image: davidscarpictures069.jpg]](http://i857.photobucket.com/albums/ab131/carolambler/davidscarpictures069.jpg)
![[Image: davidscarpictures066.jpg]](http://i857.photobucket.com/albums/ab131/carolambler/davidscarpictures066.jpg)
![[Image: davidscarpictures065.jpg]](http://i857.photobucket.com/albums/ab131/carolambler/davidscarpictures065.jpg)
Users browsing this thread:
13 Guest(s)
13 Guest(s)
Users browsing this thread:
13 Guest(s)
13 Guest(s)