617 engine rebuild thread opinions
617 engine rebuild thread opinions
Since 'doing it by the book' is outlined in the FSM, this will be more like doing the best you can with what you have.
Feel free to opine so I don't forget anything.
totaldisaster
04-04-2011, 11:39 AM #1I am putting together a rebuild thread for the 617 turbo. It will be geared towards the backyard type and incorporate simple measurements / inspection of critical items without rare or expensive tools.
Since 'doing it by the book' is outlined in the FSM, this will be more like doing the best you can with what you have.
Feel free to opine so I don't forget anything.
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-04-2011, 04:14 PM #2Look forward to this!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
make a list of all the thread specs for each thing. it would be super convenient to have a BOM for replacing all the normal metric bolts / nuts / washers so that you could just go to lowes and get a basket full of all replacement grade 8 hardware without needing to bring all the old ones in for comparison.
(04-04-2011, 07:12 PM)stan [ snip ] that you could just go to lowes and get a basket full of all replacement grade 8 hardware [ /snip ]
Ewwww! Non-OEM /OEM equivalent bolts on this thing makes me cringe... I just have this thing about seeing hex heads where there were socket head cap screws before...
Purely aesthetic reasons on my part, I just can't stand the difference.
1990 Power Ram 50 V6 SOHC 24V 6g72
I can be wrong, don't take everything I say as verbatim, please fact-check first.
My posts are my personal opinions and thoughts, unless otherwise noted.
Sounds like a good plan, just be carefull to specify that there are possible problems when it's not done by the book.
(04-04-2011, 07:12 PM)stan [ snip ] that you could just go to lowes and get a basket full of all replacement grade 8 hardware [ /snip ]
Ewwww! Non-OEM /OEM equivalent bolts on this thing makes me cringe... I just have this thing about seeing hex heads where there were socket head cap screws before...
Purely aesthetic reasons on my part, I just can't stand the difference.
1990 Power Ram 50 V6 SOHC 24V 6g72
I can be wrong, don't take everything I say as verbatim, please fact-check first.
My posts are my personal opinions and thoughts, unless otherwise noted.
3 Guest(s)
3 Guest(s)