Vacuum and fuel cut
Vacuum and fuel cut
Fuel Cut- does the fuel cut have constant vacuum going to it and cut the vacuum when you turn the key off, or is it the opposite?
Alda Vacuum- Can I just hook all of these lines up to the main vacuum line, or do they need to connect in a certain order?
by the end of today I think this will be all I have left to do, going to finish the cooling and electrcal this afternoon, I would love to take her for a test drive tonight...
if anyone has any insight it would be great.
Here is a link to the swap.
http://www.4btswaps.com/forum/showthread.php?t=8362
Swapping an OM617 into my Toyota... I did not pay enough attention when I pulled the motor to the Vacuum system.
Fuel Cut- does the fuel cut have constant vacuum going to it and cut the vacuum when you turn the key off, or is it the opposite?
Alda Vacuum- Can I just hook all of these lines up to the main vacuum line, or do they need to connect in a certain order?
by the end of today I think this will be all I have left to do, going to finish the cooling and electrcal this afternoon, I would love to take her for a test drive tonight...
if anyone has any insight it would be great.
Here is a link to the swap.
http://www.4btswaps.com/forum/showthread.php?t=8362
(04-08-2009, 11:07 AM)winmutt Fuel cut: vac == shutoff.
ALDA: has no vacuum, that is boost from the back of the intake manifold.
therfore the fuel cut needs vacuum for the engine to start? I have a solenoid I can use to turn it off, so I just need to hook it to the vacuum pump?
there are a few vacuum lines on top of the IP... where do they go? Thanks I am kind of lost on this setup.
A is boost to ARV - (WHAT IS THE ARV)
B is boost from manifold - ( Front of manifold)
E is shutoff valve i think (NEEDS FULLTIME VAC TO RUN?)
C is vac vent from cabin (NOT NEEDED?)
D is either from the main vac line or to the trans cant remember.(NOT NEEDED?)
(04-08-2009, 11:07 AM)winmutt Fuel cut: vac == shutoff.
ALDA: has no vacuum, that is boost from the back of the intake manifold.
therfore the fuel cut needs vacuum for the engine to start? I have a solenoid I can use to turn it off, so I just need to hook it to the vacuum pump?
there are a few vacuum lines on top of the IP... where do they go? Thanks I am kind of lost on this setup.
A is boost to ARV - (WHAT IS THE ARV)
B is boost from manifold - ( Front of manifold)
E is shutoff valve i think (NEEDS FULLTIME VAC TO RUN?)
C is vac vent from cabin (NOT NEEDED?)
D is either from the main vac line or to the trans cant remember.(NOT NEEDED?)
Ich liebe meine Autos!
1981 Mercedes-Benz 300SD | 156K Miles | 2nd Owner | EGR Disabled [Removal Pending] | ALDA Removed | Straight Pipes | GT2256V??? | Laser Interceptor | Engine swap over summer, hopefully with GT2256V attached...
1981 Mercedes-Benz 300SD | Odo Stopped at 160K (at least 50K more) | EGR Disabled | ALDA All The Way Out | Straight pipes | FM-870 Remote Start Alarm System | B100 Biodiesel | AC Fixed x2 | Trunk crushed in
| Retired to garage.Excessive speeding? It ain't excessive till I redline!
The engine STOPS when vacuum is applied to the fuel shutoff. Are you using a mercedes automatic transmission? C and D can be ignored if your not. The ARV is an emissions device, you most likely want to disable/remove it during the swap, just cap that off or replace it with a standard banjo bolt without the hose nipple.
Ich liebe meine Autos!
1981 Mercedes-Benz 300SD | 156K Miles | 2nd Owner | EGR Disabled [Removal Pending] | ALDA Removed | Straight Pipes | GT2256V??? | Laser Interceptor | Engine swap over summer, hopefully with GT2256V attached...
1981 Mercedes-Benz 300SD | Odo Stopped at 160K (at least 50K more) | EGR Disabled | ALDA All The Way Out | Straight pipes | FM-870 Remote Start Alarm System | B100 Biodiesel | AC Fixed x2 | Trunk crushed in
| Retired to garage.Excessive speeding? It ain't excessive till I redline!
I got the truck started, it will run for 5 to 10 seconds and then dies, no matter how I have the throttle applied, It will do this over and over again no problem... It is not the fuel cut as I applied vac to it and the truck wont start at all... what am I missing? any ideas?
Figured out the glow plugs...
I got the truck started, it will run for 5 to 10 seconds and then dies, no matter how I have the throttle applied, It will do this over and over again no problem... It is not the fuel cut as I applied vac to it and the truck wont start at all... what am I missing? any ideas?
(04-09-2009, 11:33 AM)winmutt Linkage WOT? Air in fuel?
ended up being the fuel cut, I forgot to plug it... I have it hooked up now to a vacuum switch so I can turn the truck off from a button on the dash.. The truck drives awsome.
![[Image: engineswaps090.jpg]](http://i434.photobucket.com/albums/qq70/defiant4wd/OM617%20swap/engineswaps090.jpg)
![[Image: th_engineswaps091.jpg]](http://i434.photobucket.com/albums/qq70/defiant4wd/OM617%20swap/th_engineswaps091.jpg)
'78 300D, OM617.912: 4spd manual, TB03 at 10PSI, 26*BTDC, DV's turned, HVAC, emissions system removed, e-fan, short ram, 3" downpipe to straight exhaust, W126 Bendix brakes, MR2 Spyder seats. 2890lbs
GREASY_BEAST
04-15-2009, 01:14 PM #13Nice job man! I like your method of marking the tranny bolt holes in the adapter. Also, it looks like the starter is in the correct place for putting a toyota tranny in a benz.. Do they make a 2WD 5spd with the same pattern? How much torque can these little things take?
6 Guest(s)
6 Guest(s)