300TDT Straight Pipe Install - Parts List
300TDT Straight Pipe Install - Parts List
Another thing I mentioned is that I'll be putting a different turbo in later and need the area where the down pipe is to be versatile. I will likely make the rearmost section where I can drop in a muffler for days when I want to be quieter.
jonbobshinigin
08-30-2011, 10:37 AM #1I've got a local shop where I get my tires that I am going to have install a 3" straight pipe setup for me. They do not have mandrel bends so if like to order all the necessary elbows and bends for them to install. Maybe one of you can help me out with a list of the bends I need?
Another thing I mentioned is that I'll be putting a different turbo in later and need the area where the down pipe is to be versatile. I will likely make the rearmost section where I can drop in a muffler for days when I want to be quieter.
cars? what cars? WHERE???
randomdude
08-30-2011, 01:55 PM #2an easier idea would be a dump, thats easier and quicker than removing a silencer.
cars? what cars? WHERE???
jonbobshinigin
08-30-2011, 02:00 PM #3Please explain...I am not dumping the exhaust out of the side as the car is a daily driver.
jonbobshinigin
08-30-2011, 10:45 PM #5If it were a track car, I'd prolly do a hood stack, or out behind front tire. Since it isn't, I am going to run it out of the rear. So I just need to know the parts and angles I need.
(08-30-2011, 10:45 PM)jonbobshinigin If it were a track car, I'd prolly do a hood stack
Lemons at least is no longer allowing hood stacks or any exaust dumping forward of or into the cabin.
1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
(08-30-2011, 10:45 PM)jonbobshinigin If it were a track car, I'd prolly do a hood stack
Lemons at least is no longer allowing hood stacks or any exaust dumping forward of or into the cabin.
1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
![[Image: 05206453.gif]](http://img851.imageshack.us/img851/594/05206453.gif)
jonbobshinigin
09-01-2011, 12:15 AM #10The shop I spoke with made it sound as if mandrel bends are only done from the factory and that regular bends works just fine. I want to go ahead and do it right! Are there shops that are able to do a full mandrel system?
(08-31-2011, 12:03 PM)Kozuka One of my 190E's just had a strait piece of pipe that went from the cat all the way to the back with slight angles so it went directly to the muffler spot. It really depends on how low you roll.
That's how mine works. A 4ft steel pipe from ebay and my first shot at welding
Turned down with a piece of the oem muffler.
4ft is kinda short. Prolly would need like 5.5 of 2.75in pipe
Nice body, tons of ridiculous mechanical issues - 300d turbo 82' /motor 85'
(08-31-2011, 12:03 PM)Kozuka One of my 190E's just had a strait piece of pipe that went from the cat all the way to the back with slight angles so it went directly to the muffler spot. It really depends on how low you roll.
That's how mine works. A 4ft steel pipe from ebay and my first shot at welding
Turned down with a piece of the oem muffler.
4ft is kinda short. Prolly would need like 5.5 of 2.75in pipe
Nice body, tons of ridiculous mechanical issues - 300d turbo 82' /motor 85'
Comparo:
![[Image: mandrel%20non%20mandrel.gif]](http://images.channeladvisor.com/Sell/SSProfiles/40000213/Images/4/mandrel%20non%20mandrel.gif)
![[Image: mandrel_bend.jpg]](http://lousplymouth.com/mandrel_bend.jpg)
NICE!:
http://www.spdexhaust.com/BendsB.html
![[Image: Mandrel-bend-90-degree_M.jpg]](http://www.kustombitz.com.au/resources/E8/2024/Image/Mandrel-bend-90-degree_M.jpg)
YUCK!:
![[Image: crinkle-bend.jpg]](http://www.supermotors.net/getfile/714259/fullsize/crinkle-bend.jpg)
![[Image: wurth_jan_03_bend_exhaust.jpg]](http://www.nsxfiles.com/images2/wurth_jan_03_bend_exhaust.jpg)
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
09-01-2011, 01:02 AM #12Regular pipe bends restrict the tube size down while mandrel bends do not. Crappy exhaust shops that do everything (brakes, trans, oil change, alignment....) will most likely NOT be able to make a nice mandrel bend while a higher end / specialty exhaust shop will.
Comparo:
NICE!:
http://www.spdexhaust.com/BendsB.html
YUCK!:
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
jonbobshinigin
09-01-2011, 12:08 PM #13I like what I saw at the spdexhaust site...what I need now is a list of parts to order so that a local shop can weld and install them for me. Mind helping me with that anyone?
F all the bending.
Nice body, tons of ridiculous mechanical issues - 300d turbo 82' /motor 85'
You just need a 6ft pipe and a turn down both in the right diameter. Then you can aim the straight pipe toward the hangers.
F all the bending.
Nice body, tons of ridiculous mechanical issues - 300d turbo 82' /motor 85'
and by dump i meant one of those little Y's you put in the exhaust somewhere around the front and you just reach under the car and take a cap off one side of the Y. so you can put the cap on and run a system with the muffler for DD duty, and then take the cap off and its a straight dump out the side. pretty cheap and much easier than removing a rear section setup.
cars? what cars? WHERE???
randomdude
09-01-2011, 01:57 PM #15any decent shop can do mandrel. at least the good ones around here do it.
and by dump i meant one of those little Y's you put in the exhaust somewhere around the front and you just reach under the car and take a cap off one side of the Y. so you can put the cap on and run a system with the muffler for DD duty, and then take the cap off and its a straight dump out the side. pretty cheap and much easier than removing a rear section setup.
cars? what cars? WHERE???
3 Guest(s)
3 Guest(s)