Push bumper
Push bumper
09-14-2010, 10:25 PM
#51
(09-14-2010, 06:19 PM)Captain America The first thing I would go for is those F'ing toll lane pole things!
Take 'em all out in one shot..
Ive taken out a few on the way to Newport Beach
In the old w116
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
09-15-2010, 12:16 AM
#52
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
09-15-2010, 12:16 AM #52How did it like it? those things are though. My buddy hit one in a Toyota SR5 with a Total Chaos front end (so it was pretty high) and one of those things broke the sealed beam headlight! I cant imagine what it would do to the plastic grill, light bezels, and lights themselves....
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
09-15-2010, 08:35 AM
#53
(09-14-2010, 09:40 AM)garage So have you hit any unsuspecting trash cans or traffic cones with that new beast of a bumper yet?
Car has been DOA for a bit, so no, but it should be running this weekend to go to the PA GTG. Got to wire up the lights still. Im curious if it will make wind noise, its totally invisible from the driver seat, which is something to remember when parallel parking!
(09-15-2010, 12:16 AM)Captain America How did it like it? those things are though. My buddy hit one in a Toyota SR5 with a Total Chaos front end (so it was pretty high) and one of those things broke the sealed beam headlight! I cant imagine what it would do to the plastic grill, light bezels, and lights themselves....
I think I will wait until I have a skid plate before I personally take on one of those spring loaded traffic posts! Whacking that thin piece of metal that covers the bottom of the radiator was the cause of a cracked plastic radiator bottom on my wagon. Its pretty exposed down there
This post was last modified: 09-15-2010, 08:38 AM by JB3.
1974 240D 617 turbo swap, W201 5-speed, in the works project
1983 240D 616 stock, DD
1989 Chevy Astro, 617 turbo swap, T5 5-speed, 4.56 diff, work van
(09-14-2010, 09:40 AM)garage So have you hit any unsuspecting trash cans or traffic cones with that new beast of a bumper yet?
Car has been DOA for a bit, so no, but it should be running this weekend to go to the PA GTG. Got to wire up the lights still. Im curious if it will make wind noise, its totally invisible from the driver seat, which is something to remember when parallel parking!
(09-15-2010, 12:16 AM)Captain America How did it like it? those things are though. My buddy hit one in a Toyota SR5 with a Total Chaos front end (so it was pretty high) and one of those things broke the sealed beam headlight! I cant imagine what it would do to the plastic grill, light bezels, and lights themselves....
I think I will wait until I have a skid plate before I personally take on one of those spring loaded traffic posts! Whacking that thin piece of metal that covers the bottom of the radiator was the cause of a cracked plastic radiator bottom on my wagon. Its pretty exposed down there
1974 240D 617 turbo swap, W201 5-speed, in the works project
1983 240D 616 stock, DD
1989 Chevy Astro, 617 turbo swap, T5 5-speed, 4.56 diff, work van
09-15-2010, 06:39 PM
#54
(09-15-2010, 12:16 AM)Captain America How did it like it? those things are though. My buddy hit one in a Toyota SR5 with a Total Chaos front end (so it was pretty high) and one of those things broke the sealed beam headlight! I cant imagine what it would do to the plastic grill, light bezels, and lights themselves....
Hahaha damnn. There was no damage to the car besides some chipped paint. Going about 75, i hit at least 3..it might have been 4
(09-15-2010, 08:35 AM)dropnosky(09-14-2010, 09:40 AM)garage So have you hit any unsuspecting trash cans or traffic cones with that new beast of a bumper yet?
Car has been DOA for a bit, so no, but it should be running this weekend to go to the PA GTG. Got to wire up the lights still. Im curious if it will make wind noise, its totally invisible from the driver seat, which is something to remember when parallel parking!
Hmm. I dont think the wind noise would be audible...idk though.
YEAH that is definetly somthing to remember when parking!!!
This post was last modified: 09-15-2010, 06:41 PM by garage.
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
(09-15-2010, 12:16 AM)Captain America How did it like it? those things are though. My buddy hit one in a Toyota SR5 with a Total Chaos front end (so it was pretty high) and one of those things broke the sealed beam headlight! I cant imagine what it would do to the plastic grill, light bezels, and lights themselves....
Hahaha damnn. There was no damage to the car besides some chipped paint. Going about 75, i hit at least 3..it might have been 4
(09-15-2010, 08:35 AM)dropnosky(09-14-2010, 09:40 AM)garage So have you hit any unsuspecting trash cans or traffic cones with that new beast of a bumper yet?
Car has been DOA for a bit, so no, but it should be running this weekend to go to the PA GTG. Got to wire up the lights still. Im curious if it will make wind noise, its totally invisible from the driver seat, which is something to remember when parallel parking!
Hmm. I dont think the wind noise would be audible...idk though.
YEAH that is definetly somthing to remember when parking!!!
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
10-24-2010, 01:02 PM
#55
the headlight covers, in anticipation of putting in a vent for air intake on the passenger side, combined with the push bumper. I think the grill needs to be black too personally.
Cant decide if I like this or not.
1974 240D 617 turbo swap, W201 5-speed, in the works project
1983 240D 616 stock, DD
1989 Chevy Astro, 617 turbo swap, T5 5-speed, 4.56 diff, work van
reviews on this combination-
the headlight covers, in anticipation of putting in a vent for air intake on the passenger side, combined with the push bumper. I think the grill needs to be black too personally.
Cant decide if I like this or not.
1974 240D 617 turbo swap, W201 5-speed, in the works project
1983 240D 616 stock, DD
1989 Chevy Astro, 617 turbo swap, T5 5-speed, 4.56 diff, work van
10-24-2010, 05:03 PM
#56
(10-24-2010, 01:02 PM)dropnosky reviews on this combination-
the headlight covers, in anticipation of putting in a vent for air intake on the passenger side, combined with the push bumper. I think the grill needs to be black too personally.
Cant decide if I like this or not.
I like the headlight covers, there unique. I think for the vent for the air intake you should put some louvers, or slots, somthing besides a hole and/or mesh. I would definetly black out the grille!! maybe the hood too?
I would say keep it like that! plus a skid
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
(10-24-2010, 01:02 PM)dropnosky reviews on this combination-
the headlight covers, in anticipation of putting in a vent for air intake on the passenger side, combined with the push bumper. I think the grill needs to be black too personally.
Cant decide if I like this or not.
I like the headlight covers, there unique. I think for the vent for the air intake you should put some louvers, or slots, somthing besides a hole and/or mesh. I would definetly black out the grille!! maybe the hood too?
I would say keep it like that! plus a skid
1987 300D: EGR Delete, ARV Delete, Cold Air Intake...
10-25-2010, 11:05 PM
#57
Black the grill, add louvers with a vac pod on the (dual?) air intakes, so you can close them up at rest.
1990 Power Ram 50 V6 SOHC 24V 6g72
I can be wrong, don't take everything I say as verbatim, please fact-check first.
My posts are my personal opinions and thoughts, unless otherwise noted.
Oooh, so minty-fresh is getting the bull bar! I Like!
Black the grill, add louvers with a vac pod on the (dual?) air intakes, so you can close them up at rest.
1990 Power Ram 50 V6 SOHC 24V 6g72
I can be wrong, don't take everything I say as verbatim, please fact-check first.
My posts are my personal opinions and thoughts, unless otherwise noted.
10-28-2010, 10:09 PM
#58
1981 Mercedes 300TD Lowered 4 speed manual Holset HX30
mike-81-240d
10-28-2010, 10:09 PM #58Black out the mirror caps too... like DieselKraut's wagon...
1981 Mercedes 300TD Lowered 4 speed manual Holset HX30
12-21-2010, 10:23 AM
#59
![[Image: 90E_6-L.jpg]](http://images.pistonheads.com/nimg/22944/90E_6-L.jpg)
http://www.pistonheads.com/news/default....ryId=22944
Yes but will it rail slide like this subaru?
http://www.youtube.com/watch?v=Dsyk17OLc...r_embedded
1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
http://www.pistonheads.com/news/default....ryId=22944
Yes but will it rail slide like this subaru?
http://www.youtube.com/watch?v=Dsyk17OLc...r_embedded
1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
08-31-2011, 08:50 AM
#61
(10-24-2010, 01:02 PM)dropnosky reviews on this combination-
the headlight covers, in anticipation of putting in a vent for air intake on the passenger side, combined with the push bumper. I think the grill needs to be black too personally.
Cant decide if I like this or not.
Looks Really bitching! How and with what did u cover up those fog lights? It looks like u just painted right over them.
This post was last modified: 08-31-2011, 08:58 AM by smoke026.
(10-24-2010, 01:02 PM)dropnosky reviews on this combination-
the headlight covers, in anticipation of putting in a vent for air intake on the passenger side, combined with the push bumper. I think the grill needs to be black too personally.
Cant decide if I like this or not.
Looks Really bitching! How and with what did u cover up those fog lights? It looks like u just painted right over them.
08-31-2011, 11:39 AM
#62
(08-31-2011, 08:50 AM)smoke026(10-24-2010, 01:02 PM)dropnosky reviews on this combination-
the headlight covers, in anticipation of putting in a vent for air intake on the passenger side, combined with the push bumper. I think the grill needs to be black too personally.
Cant decide if I like this or not.
Looks Really bitching! How and with what did u cover up those fog lights? It looks like u just painted right over them.
thanks! Those are made of polystyrene with a home made thermoform machine.
heres the thread-
http://www.superturbodiesel.com/std/Thre...ight-doors
1974 240D 617 turbo swap, W201 5-speed, in the works project
1983 240D 616 stock, DD
1989 Chevy Astro, 617 turbo swap, T5 5-speed, 4.56 diff, work van
(08-31-2011, 08:50 AM)smoke026(10-24-2010, 01:02 PM)dropnosky reviews on this combination-
the headlight covers, in anticipation of putting in a vent for air intake on the passenger side, combined with the push bumper. I think the grill needs to be black too personally.
Cant decide if I like this or not.
Looks Really bitching! How and with what did u cover up those fog lights? It looks like u just painted right over them.
thanks! Those are made of polystyrene with a home made thermoform machine.
heres the thread-
http://www.superturbodiesel.com/std/Thre...ight-doors
1974 240D 617 turbo swap, W201 5-speed, in the works project
1983 240D 616 stock, DD
1989 Chevy Astro, 617 turbo swap, T5 5-speed, 4.56 diff, work van
12-30-2013, 01:45 PM
#63
-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
12-30-2013, 01:45 PM #63I'm thinking of building a push bumper over break, but if I do I think I'll make a whole new bumper instead of keeping the stock one, but using the stock bumper shocks. We'll see
-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
01-02-2014, 04:11 PM
#64
(12-30-2013, 01:45 PM)sassparilla_kid I'm thinking of building a push bumper over break, but if I do I think I'll make a whole new bumper instead of keeping the stock one, but using the stock bumper shocks. We'll see
woot! like one of those diamond plate steel pickup truck ones? Add a winch.
" straighten up that star on the grill, assholes."
lgreeley83
01-02-2014, 04:11 PM #64(12-30-2013, 01:45 PM)sassparilla_kid I'm thinking of building a push bumper over break, but if I do I think I'll make a whole new bumper instead of keeping the stock one, but using the stock bumper shocks. We'll see
woot! like one of those diamond plate steel pickup truck ones? Add a winch.
" straighten up that star on the grill, assholes."
01-04-2014, 03:46 PM
#65
-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
01-04-2014, 03:46 PM #65lgreeley probably something like this
-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
01-04-2014, 03:53 PM
#66
" straighten up that star on the grill, assholes."
lgreeley83
01-04-2014, 03:53 PM #66Awesome. Exactly like I was thinking. I was in San Antonio for a few months back in '09... Close to 50% of the pick up trucks had bumpers like that, front and back. Youve got a fan here if you do it!
" straighten up that star on the grill, assholes."
Users browsing this thread:
12 Guest(s)
12 Guest(s)
Users browsing this thread:
12 Guest(s)
12 Guest(s)