EATON M112 AND ????? TURBO
EATON M112 AND ????? TURBO
for my new drift car i would like at least 500bhp, i am going to force feed the turbo intake with the eaton m112 and then use a bypass valve when the blower runs out of steam. This is the om606 engine.
I like the holset hx35 i used before(OM605), although it was slow to spool. It will be too small now anyway.
I want it to spool as fast as possible, the question is: what turbo?
Is a hx55 too big?
Hi,
for my new drift car i would like at least 500bhp, i am going to force feed the turbo intake with the eaton m112 and then use a bypass valve when the blower runs out of steam. This is the om606 engine.
I like the holset hx35 i used before(OM605), although it was slow to spool. It will be too small now anyway.
I want it to spool as fast as possible, the question is: what turbo?
Is a hx55 too big?
(11-14-2012, 05:29 PM)mantahead hi,
can't get a hold of a hx52 at the right money, what about a garret Gt4088 with a 1.06 AR exhaust housing.
(11-14-2012, 06:28 PM)Turbo Pekka Herlevi suggested for me hx 50 compressor 63mm and exhaust 73mm exhaust housing size 14-16cm3, but spool was not impressive at allwhat kinda power would the hx50 make?
(11-14-2012, 05:29 PM)mantahead hi,
can't get a hold of a hx52 at the right money, what about a garret Gt4088 with a 1.06 AR exhaust housing.
the charger should speed up the spool up hopefully.
(11-14-2012, 06:28 PM)Turbo Pekka Herlevi suggested for me hx 50 compressor 63mm and exhaust 73mm exhaust housing size 14-16cm3, but spool was not impressive at allwhat kinda power would the hx50 make?
(11-14-2012, 05:29 PM)mantahead hi,
can't get a hold of a hx52 at the right money, what about a garret Gt4088 with a 1.06 AR exhaust housing.
the charger should speed up the spool up hopefully.
quote='mantahead' pid='45982' dateline='1352936351']
(11-14-2012, 06:28 PM)Turbo Pekka Herlevi suggested for me hx 50 compressor 63mm and exhaust 73mm exhaust housing size 14-16cm3, but spool was not impressive at allwhat kinda power would the hx50 make?
(11-14-2012, 05:29 PM)mantahead hi,
can't get a hold of a hx52 at the right money, what about a garret Gt4088 with a 1.06 AR exhaust housing.
the charger should speed up the spool up hopefully.
[/quote]
I ask for a turbo suggestions for +600hk and Pekka gave that suggestion, I never tried it since I am retuning and building the engine for higher purpose
quote='mantahead' pid='45982' dateline='1352936351']
(11-14-2012, 06:28 PM)Turbo Pekka Herlevi suggested for me hx 50 compressor 63mm and exhaust 73mm exhaust housing size 14-16cm3, but spool was not impressive at allwhat kinda power would the hx50 make?
(11-14-2012, 05:29 PM)mantahead hi,
can't get a hold of a hx52 at the right money, what about a garret Gt4088 with a 1.06 AR exhaust housing.
the charger should speed up the spool up hopefully.
[/quote]
EDH_Performance
11-16-2012, 09:10 AM #8I am going to use a hx52 with billet wheel and 16cm2 exhousing in a compound setup on mye engine
5 Guest(s)
5 Guest(s)