Picture Request: 606 linkages
Picture Request: 606 linkages
12-15-2012, 01:24 PM
#1
For my swap I am going to most likely stick with my automatic transmission unless I can somehow find a 190E 5 speed setup.
Could some of you guys with 606's in W124's take some pictures of how you are setting up the throttle linkages please. It's one of the issues that isn't well documented for the 606 -> w124 swap.
For my swap I am going to most likely stick with my automatic transmission unless I can somehow find a 190E 5 speed setup.
12-15-2012, 01:40 PM
#2
(12-15-2012, 01:24 PM)TheDon Could some of you guys with 606's in W124's take some pictures of how you are setting up the throttle linkages please. It's one of the issues that isn't well documented for the 606 -> w124 swap.
For my swap I am going to most likely stick with my automatic transmission unless I can somehow find a 190E 5 speed setup.
hi don, i posted pictures on your 'picked 606 thread' of my linkage solutions one on a g wagen with 606a and one on a 190e with 606a
hope these help with ideas -mike
(12-15-2012, 01:24 PM)TheDon Could some of you guys with 606's in W124's take some pictures of how you are setting up the throttle linkages please. It's one of the issues that isn't well documented for the 606 -> w124 swap.
For my swap I am going to most likely stick with my automatic transmission unless I can somehow find a 190E 5 speed setup.
hi don, i posted pictures on your 'picked 606 thread' of my linkage solutions one on a g wagen with 606a and one on a 190e with 606a
hope these help with ideas -mike
12-15-2012, 06:44 PM
#4
(12-15-2012, 03:51 PM)TheDon Possibly, which car did that bracket come off of, the bracket by the intake manifold.hello 'the don' i am running manual 6 speed trans in g wagen and 5 speed manual in the 190 e. for the 190 e i used all new parts ordered for a n/a 2.5 diesel 190 (602 engine) i cut the linkage up and sawed a hole in the web in the inlet manifold to 'sink' it down so it cleared the bonnet or 'hood' i altered the underneath of the plastic cover and ran the cable through the inside so i could use the factory 190e 2.6 gasser cable ,sorry i had not ground and painted it !
Are you running with an auto or manual transmission?
the g wagen one i used the linkage from n/a 606 engined w124 and yet again cut it and altered to suit and holesawed down through the manifold web for the rod linkage and a small 'mousehole' in the cover to clear for the fixing . both work really well - mike
(12-15-2012, 03:51 PM)TheDon Possibly, which car did that bracket come off of, the bracket by the intake manifold.hello 'the don' i am running manual 6 speed trans in g wagen and 5 speed manual in the 190 e. for the 190 e i used all new parts ordered for a n/a 2.5 diesel 190 (602 engine) i cut the linkage up and sawed a hole in the web in the inlet manifold to 'sink' it down so it cleared the bonnet or 'hood' i altered the underneath of the plastic cover and ran the cable through the inside so i could use the factory 190e 2.6 gasser cable ,sorry i had not ground and painted it !
Are you running with an auto or manual transmission?
the g wagen one i used the linkage from n/a 606 engined w124 and yet again cut it and altered to suit and holesawed down through the manifold web for the rod linkage and a small 'mousehole' in the cover to clear for the fixing . both work really well - mike
Users browsing this thread:
5 Guest(s)
5 Guest(s)
Users browsing this thread:
5 Guest(s)
5 Guest(s)