anyone know the normal system pressure for SLS?
anyone know the normal system pressure for SLS?
Whole deal is I'd like to throw a tandem pump in my truck and use the PS side for PS, and the SLS side for HydroBoost, since the GM pumps are freaking huge and I'd rather keep it Benz, Bosch, or Mitsubishi...
Of course, if I can get 1500 PSI out of a Benz PS pump by shiming it, and it doesn't grenade/boil fluid, I'll be happy.
1990 Power Ram 50 V6 SOHC 24V 6g72
I can be wrong, don't take everything I say as verbatim, please fact-check first.
My posts are my personal opinions and thoughts, unless otherwise noted.
Been looking in all the FSM's I've come across, can't seem to find a single one that lists the system pressure...
Whole deal is I'd like to throw a tandem pump in my truck and use the PS side for PS, and the SLS side for HydroBoost, since the GM pumps are freaking huge and I'd rather keep it Benz, Bosch, or Mitsubishi...
Of course, if I can get 1500 PSI out of a Benz PS pump by shiming it, and it doesn't grenade/boil fluid, I'll be happy.
1990 Power Ram 50 V6 SOHC 24V 6g72
I can be wrong, don't take everything I say as verbatim, please fact-check first.
My posts are my personal opinions and thoughts, unless otherwise noted.
i have a 617 from a 300tdt, so i garbed the reservoir and lines . these pumps a big bucks new , so i dont want to remove it
plus not needing vacume is nice
please elaborate , i was wondering the output of these pumps as well , you said they are not always under pressure?. i too woill be trying to adapt a hydro boost brake setup .
i have a 617 from a 300tdt, so i garbed the reservoir and lines . these pumps a big bucks new , so i dont want to remove it
plus not needing vacume is nice
(01-23-2013, 08:46 PM)aaa The sls valve is not always putting a load on the pump, it recirculates fluid most of the time.
Sounds like a good fit for brakes to me-it should only be under load when you're braking, right?
Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
Simpler=Better
01-24-2013, 04:12 PM #5(01-23-2013, 08:46 PM)aaa The sls valve is not always putting a load on the pump, it recirculates fluid most of the time.
Sounds like a good fit for brakes to me-it should only be under load when you're braking, right?
Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
min 130 / max 185 bar
idle 130 bar
you just need to know where to look...
(06-18-2011, 11:36 PM)300D50 Been looking in all the FSM's I've come across, can't seem to find a single one that lists the system pressure...
Whole deal is I'd like to throw a tandem pump in my truck and use the PS side for PS, and the SLS side for HydroBoost, since the GM pumps are freaking huge and I'd rather keep it Benz, Bosch, or Mitsubishi...
Of course, if I can get 1500 PSI out of a Benz PS pump by shiming it, and it doesn't grenade/boil fluid, I'll be happy.
Austincarnut
01-24-2013, 08:30 PM #6SLS spec pressures:
min 130 / max 185 bar
idle 130 bar
you just need to know where to look...
(06-18-2011, 11:36 PM)300D50 Been looking in all the FSM's I've come across, can't seem to find a single one that lists the system pressure...
Whole deal is I'd like to throw a tandem pump in my truck and use the PS side for PS, and the SLS side for HydroBoost, since the GM pumps are freaking huge and I'd rather keep it Benz, Bosch, or Mitsubishi...
Of course, if I can get 1500 PSI out of a Benz PS pump by shiming it, and it doesn't grenade/boil fluid, I'll be happy.
is this valve , rpm regulated or pump out put , across rpm?
im still not sure the opp range of most hydro boosters so ill look into it .
i see , thanks you for posting this speck Austincarnut . as far as the Recurc Valve for this pump is it internal to the pump or would it have been in the associated plumbing still on the car? i only grabbed the high pressure hose that went to a Tblock i believe , and the low feed to the pump still on the resivior.
is this valve , rpm regulated or pump out put , across rpm?
im still not sure the opp range of most hydro boosters so ill look into it .
i see, thank you so the pumps out put is variable 130 -180 , depending on rpm . then the valve it the back decides whether the resiviors want more or less to do there thing ? i think i can still get that valve from the parts car. just incase . but ill find out if the boosters operate a constant ,regulated or bypassed . i suppose , as long as the hyboost in the same psi range . it should be a matter of lines and a couple valves . maybe a fancy fill can for the return .
5 Guest(s)
5 Guest(s)