White smoke problem OM603 7MM IP
White smoke problem OM603 7MM IP
06-22-2013, 01:26 PM
#1
Have checked the ip timing 5-6 times and it is 14 degrees after, since the pump is 0,5 degrees late in the bench.
Just changed my headgasket but not sure if everything is ok since it puffs a bit from the crankvent. My injectors are cheked and recheked 120-135 bar openingpressure and just did an compression test around 24 bar on every cylinder! Open for any suggestions running out of ideas.. Just want to know if its worth fixing or if i should just get another enginge.
Thankful for any help//Reed from Sweden
Got a big problem with my OM603, it starts good and runs well but im getting white instead of black smoke, and it smells like barbeque/ burning lighterfluid (unburnt diesel?)
Have checked the ip timing 5-6 times and it is 14 degrees after, since the pump is 0,5 degrees late in the bench.
Just changed my headgasket but not sure if everything is ok since it puffs a bit from the crankvent. My injectors are cheked and recheked 120-135 bar openingpressure and just did an compression test around 24 bar on every cylinder! Open for any suggestions running out of ideas.. Just want to know if its worth fixing or if i should just get another enginge.
Thankful for any help//Reed from Sweden
06-22-2013, 01:49 PM
#2
(06-22-2013, 01:26 PM)Hearns Got a big problem with my OM603, it starts good and runs well but im getting white instead of black smoke, and it smells like barbeque/ burning lighterfluid (unburnt diesel?)check that engine is on tdc for number 1 cylinder and not 6
Have checked the ip timing 5-6 times and it is 14 degrees after, since the pump is 0,5 degrees late in the bench.
Just changed my headgasket but not sure if everything is ok since it puffs a bit from the crankvent. My injectors are cheked and recheked 120-135 bar openingpressure and just did an compression test around 24 bar on every cylinder! Open for any suggestions running out of ideas.. Just want to know if its worth fixing or if i should just get another enginge.
Thankful for any help//Reed from Sweden
engine might need turned full revolution to suit pump.
(06-22-2013, 01:26 PM)Hearns Got a big problem with my OM603, it starts good and runs well but im getting white instead of black smoke, and it smells like barbeque/ burning lighterfluid (unburnt diesel?)check that engine is on tdc for number 1 cylinder and not 6
Have checked the ip timing 5-6 times and it is 14 degrees after, since the pump is 0,5 degrees late in the bench.
Just changed my headgasket but not sure if everything is ok since it puffs a bit from the crankvent. My injectors are cheked and recheked 120-135 bar openingpressure and just did an compression test around 24 bar on every cylinder! Open for any suggestions running out of ideas.. Just want to know if its worth fixing or if i should just get another enginge.
Thankful for any help//Reed from Sweden
engine might need turned full revolution to suit pump.
06-22-2013, 02:20 PM
#3
(06-22-2013, 01:49 PM)mantahead(06-22-2013, 01:26 PM)Hearns Got a big problem with my OM603, it starts good and runs well but im getting white instead of black smoke, and it smells like barbeque/ burning lighterfluid (unburnt diesel?)check that engine is on tdc for number 1 cylinder and not 6
Have checked the ip timing 5-6 times and it is 14 degrees after, since the pump is 0,5 degrees late in the bench.
Just changed my headgasket but not sure if everything is ok since it puffs a bit from the crankvent. My injectors are cheked and recheked 120-135 bar openingpressure and just did an compression test around 24 bar on every cylinder! Open for any suggestions running out of ideas.. Just want to know if its worth fixing or if i should just get another enginge.
Thankful for any help//Reed from Sweden
engine might need turned full revolution to suit pump.
it's at TDC for cyl1.
Forgot to mention that im running it N/A right now, And it runs like a turbo enginge, slow from the start and then increasing power and im not running ALDA right now for more fuel.
(06-22-2013, 01:49 PM)mantahead(06-22-2013, 01:26 PM)Hearns Got a big problem with my OM603, it starts good and runs well but im getting white instead of black smoke, and it smells like barbeque/ burning lighterfluid (unburnt diesel?)check that engine is on tdc for number 1 cylinder and not 6
Have checked the ip timing 5-6 times and it is 14 degrees after, since the pump is 0,5 degrees late in the bench.
Just changed my headgasket but not sure if everything is ok since it puffs a bit from the crankvent. My injectors are cheked and recheked 120-135 bar openingpressure and just did an compression test around 24 bar on every cylinder! Open for any suggestions running out of ideas.. Just want to know if its worth fixing or if i should just get another enginge.
Thankful for any help//Reed from Sweden
engine might need turned full revolution to suit pump.
it's at TDC for cyl1.
Forgot to mention that im running it N/A right now, And it runs like a turbo enginge, slow from the start and then increasing power and im not running ALDA right now for more fuel.
offroaddieselhu
06-22-2013, 02:53 PM #4https://www.youtube.com/watch?v=PUcb5G9s0RY
That's your problem?
06-24-2013, 06:47 AM
#6
(06-22-2013, 02:53 PM)offroaddieselhu https://www.youtube.com/watch?v=PUcb5G9s0RY
That's your problem?
Yes pretty much, white/black smoke on idle, and then more and more smoke when i rev!
(06-22-2013, 03:17 PM)Domino81 if you are not missing air.. maybe inlet is too small? i had the same problem..rubber inlet elements would suck-in when much air was needed, the effect was the same - white smoke..
I have tried running it without intake also and right now im just using a turbo intake but its just sucking air not blowing.
Starting to suspect that the turbo is the issue.. The white smoke could be oil and the performance decrease could me the turbo not spooling and creating backpressure so that the exhaustgases cant escape?
Starting to suspect that the turbo is the issue.. The white smoke could be oil and the performance decrease could me the turbo not spooling and creating backpressure so that the exhaustgases cant escape?
This post was last modified: 06-24-2013, 06:52 AM by Hearns.
(06-22-2013, 02:53 PM)offroaddieselhu https://www.youtube.com/watch?v=PUcb5G9s0RY
That's your problem?
Yes pretty much, white/black smoke on idle, and then more and more smoke when i rev!
(06-22-2013, 03:17 PM)Domino81 if you are not missing air.. maybe inlet is too small? i had the same problem..rubber inlet elements would suck-in when much air was needed, the effect was the same - white smoke..
I have tried running it without intake also and right now im just using a turbo intake but its just sucking air not blowing.
Starting to suspect that the turbo is the issue.. The white smoke could be oil and the performance decrease could me the turbo not spooling and creating backpressure so that the exhaustgases cant escape?
Starting to suspect that the turbo is the issue.. The white smoke could be oil and the performance decrease could me the turbo not spooling and creating backpressure so that the exhaustgases cant escape?
06-24-2013, 02:57 PM
#8
The ALDA limits the fuel until there is boost pressure
This post was last modified: 06-24-2013, 02:58 PM by willbhere4u.
1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
06-24-2013, 02:57 PM #8Removed ALDA means = 100% fuel
The ALDA limits the fuel until there is boost pressure
1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
06-24-2013, 03:06 PM
#9
(06-24-2013, 02:57 PM)willbhere4u Removed ALDA means = 100% fuel
The ALDA limits the fuel until there is boost pressure
Yeah i know, bad choice of words! I meant that i removed it from the pump to get max fuel all the way! Otherwise i get full fuel at 0.7 bar.
06-25-2013, 09:38 AM
#11
1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
06-25-2013, 09:38 AM #11Try putting the ALDA back on until the turbo is pushing boost through the engine Evan the big pump guys need them to keep them from smoking at idle!!!
1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
Users browsing this thread:
10 Guest(s)
10 Guest(s)
Users browsing this thread:
10 Guest(s)
10 Guest(s)