OM617 more power at low RPM
OM617 more power at low RPM
The turbo is clocked and installed with the small Land Rover TDI intercooler.
Would like a little more power at lower RPMs, so was thinking of adding a VGT in place of the stock turbo.
Did a quick search and didn't see much on the OM617 VGT... could have missed it, but was looking for something cheap to start with that could be pulled off an engine at a junk yard or pick-n-pull and then work up to buying a new model after it is proven to be a positive upgrade.
Thoughts?
rdavisinva
10-24-2013, 02:37 PM #1So the OM617 has beein installed in out Land Rover 110 for just over a year now and it runs very well.
The turbo is clocked and installed with the small Land Rover TDI intercooler.
Would like a little more power at lower RPMs, so was thinking of adding a VGT in place of the stock turbo.
Did a quick search and didn't see much on the OM617 VGT... could have missed it, but was looking for something cheap to start with that could be pulled off an engine at a junk yard or pick-n-pull and then work up to buying a new model after it is proven to be a positive upgrade.
Thoughts?
Whats your tranmission setup? With the an automatic mercedes transmission I would simply use the higher-stall torque converter which lets the stock turbo spool up easily. Got a boost gauge to see what your turbo is doing now?
GT2256v sounds like what you're looking for. Small easy to find VNT turbo (from the Sprinter vans).
Whats your tranmission setup? With the an automatic mercedes transmission I would simply use the higher-stall torque converter which lets the stock turbo spool up easily. Got a boost gauge to see what your turbo is doing now?
2056v is a little smaller, can be found on Jeep liberty CRDs. Also known as the "M53" turbo
Is your ALDA tuend?
Have you advanced your timing?
You can also tweak the guts of your pump (I believe)
Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
Simpler=Better
10-24-2013, 06:29 PM #3No need for a new turbo, junkyard ones are A-OK so long as there's no shaft play
2056v is a little smaller, can be found on Jeep liberty CRDs. Also known as the "M53" turbo
Is your ALDA tuend?
Have you advanced your timing?
You can also tweak the guts of your pump (I believe)
Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
I've seen them for sale for as low as $37.50 with zero shaft play (electronics overheat & its "cheaper to replace the entire unit".
The 2056 is a little scarce in the USofA as they only came on Jeep KJ Liberty (Cherokee) 2005-06.
I'm interested in upgrading my 2056 but I'm still saving for a superpump.
'05 Jeep Liberty CRD - 160k
'06.5 VW Jetta TDI - 230k
'82 MB 300TD - 116k (motor going to raysorenson)
'81 MB 300TD - 195k (parting out)
'71 Jeep DJ5 - diesel conversion project
X2 on the Garrett GT2256v off of sprinter vans.
I've seen them for sale for as low as $37.50 with zero shaft play (electronics overheat & its "cheaper to replace the entire unit".
The 2056 is a little scarce in the USofA as they only came on Jeep KJ Liberty (Cherokee) 2005-06.
I'm interested in upgrading my 2056 but I'm still saving for a superpump.
'05 Jeep Liberty CRD - 160k
'06.5 VW Jetta TDI - 230k
'82 MB 300TD - 116k (motor going to raysorenson)
'81 MB 300TD - 195k (parting out)
'71 Jeep DJ5 - diesel conversion project
http://www.superturbodiesel.com/std/Thre...NT-project
raysorenson
10-24-2013, 09:36 PM #5Check this guy's thread out. Good VNT stuff on a 617.
http://www.superturbodiesel.com/std/Thre...NT-project
The transmission is currently a manual 5 speed LT77 which will be upgraded in the future to the R380 5 speed.
The pump including ALDA has not been tuned nor the timing set.
I understand that tuning will help, but was initially more concerned about the lack of boost at low RPMs thinking it was a no-brainer to locate a VNT that would provide some boost at lower RPM.
I'll check out the link raysorenson provided and probably have a few more questions.
Saw this on eBay:
http://www.ebay.com/itm/MERCEDES-BENZ-SP...bf&vxp=mtr
This looks OK with a broken electronics box, but looks pricy compared to the cheap ones mentioned.
rdavisinva
10-28-2013, 03:13 PM #6Thanks to all of you for the replies.
The transmission is currently a manual 5 speed LT77 which will be upgraded in the future to the R380 5 speed.
The pump including ALDA has not been tuned nor the timing set.
I understand that tuning will help, but was initially more concerned about the lack of boost at low RPMs thinking it was a no-brainer to locate a VNT that would provide some boost at lower RPM.
I'll check out the link raysorenson provided and probably have a few more questions.
Saw this on eBay:
http://www.ebay.com/itm/MERCEDES-BENZ-SP...bf&vxp=mtr
This looks OK with a broken electronics box, but looks pricy compared to the cheap ones mentioned.
Nice body, tons of ridiculous mechanical issues - 300d turbo 82' /motor 85'
(10-28-2013, 03:13 PM)rdavisinva ....
Saw this on eBay:
http://www.ebay.com/itm/MERCEDES-BENZ-SP...bf&vxp=mtr
This looks OK with a broken electronics box, but looks pricy compared to the cheap ones mentioned.
I don't think I ever seen a GT2256v on sale for less that $150.00.
I do have a vacuum actuated unit for sale, but it is quite a bit more than $150.
.
Gota love Mercedes Diesels!
.
DeliveryValve
10-28-2013, 06:38 PM #8(10-28-2013, 03:13 PM)rdavisinva ....
Saw this on eBay:
http://www.ebay.com/itm/MERCEDES-BENZ-SP...bf&vxp=mtr
This looks OK with a broken electronics box, but looks pricy compared to the cheap ones mentioned.
I don't think I ever seen a GT2256v on sale for less that $150.00.
I do have a vacuum actuated unit for sale, but it is quite a bit more than $150.
.
Gota love Mercedes Diesels!
.
(10-28-2013, 05:11 PM)larsalan To me the stock turbo will come on very quick if alda is maxed. My alda is delete and straight exhaust, can hear turbo even at idle.
My hx30 singggs! My buddy said at the dyno competition I should have won an award for loudest turbo
'82 300D -3" straight pipe, ALDA deleted, 3in1 glowshift gauge, HX30, egr-less manifold, A/W intercooler
'14 Ram 6.7l cummins -G56 handshaker, wishing it was deleted
(10-28-2013, 05:11 PM)larsalan To me the stock turbo will come on very quick if alda is maxed. My alda is delete and straight exhaust, can hear turbo even at idle.
My hx30 singggs! My buddy said at the dyno competition I should have won an award for loudest turbo
'82 300D -3" straight pipe, ALDA deleted, 3in1 glowshift gauge, HX30, egr-less manifold, A/W intercooler
'14 Ram 6.7l cummins -G56 handshaker, wishing it was deleted
raysorenson
10-29-2013, 11:27 AM #10Even with a 100:1 or better crawl ratio and 35" tires, I've seen people say an OM617 has room for improvement in the low rpm torque department. I'm thinking 5psi by 1200-1300 rpm would make a nice crawler engine.
english red rat rod 1977 240D, OM617.952 burning B99.9, iron 4-speed & 2.88 diff, 195/60/R14 on alloys, 5mph bumpers, battery in the trunk, 25mm swaybar, 4x ECE H4 lamps, double brake lamps, deleted sunroof, export zoll & california blue plates
where have you guys found wrecked sprinters?
english red rat rod 1977 240D, OM617.952 burning B99.9, iron 4-speed & 2.88 diff, 195/60/R14 on alloys, 5mph bumpers, battery in the trunk, 25mm swaybar, 4x ECE H4 lamps, double brake lamps, deleted sunroof, export zoll & california blue plates
At first had a 1.6 transfer case, but the gearing was too low.
Will have to check out the pump adjustment, but think some low end boost would greatly help.
rdavisinva
10-29-2013, 09:19 PM #14Currently running 3.54 gears with a 1.4 transfer case.
At first had a 1.6 transfer case, but the gearing was too low.
Will have to check out the pump adjustment, but think some low end boost would greatly help.
http://turbobricks.com/forums/showthread...245&page=2
While I need schooling on the OM617 IP adjustments, do lots of mechanical work, so it must be time to dive in.
There were some threads here on IP adjustment I looked at a while back.
MY setup has a small intercooler so that should help cool the intake charge.
rdavisinva
10-31-2013, 07:02 AM #16No have not made any adjustments, but by coincidence looked at this thread last night which also mentions the torque limiter:
http://turbobricks.com/forums/showthread...245&page=2
While I need schooling on the OM617 IP adjustments, do lots of mechanical work, so it must be time to dive in.
There were some threads here on IP adjustment I looked at a while back.
MY setup has a small intercooler so that should help cool the intake charge.
Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
Simpler=Better
10-31-2013, 08:21 AM #17You have to be patient to find a cheap turbo. I paid $120 shipped for my 2056V on ebay
Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
https://docs.google.com/document/d/1Navs...J1HNc/edit
raysorenson
10-31-2013, 11:44 AM #18Here's a copy of OM616's MW tuning document, penned by him. You probably won't find better info than this.
https://docs.google.com/document/d/1Navs...J1HNc/edit
carlitosgy6
10-31-2013, 04:42 PM #19if you max the alda you will get faster boost and more low end torque,i was using a garret stock turbo and i replaced it for a kkk k26 stock turbo ,for me it works better,lower rpm boost got better and its sounds beautiful
rdavisinva
11-01-2013, 01:46 PM #20Thanks for all the suggestions... so many mechanical opportunities, so little time!
(10-31-2013, 04:42 PM)carlitosgy6 if you max the alda you will get faster boost and more low end torque,i was using a garret stock turbo and i replaced it for a kkk k26 stock turbo ,for me it works better,lower rpm boost got better and its sounds beautiful
Ditto alda maxed and the factory kkk26 turbo any you've got great power by 2k
my dads 84 300d was a rocket out of the lights to about 40mph I also had the non EGR manifolds on it for him
1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
11-01-2013, 04:33 PM #21(10-31-2013, 04:42 PM)carlitosgy6 if you max the alda you will get faster boost and more low end torque,i was using a garret stock turbo and i replaced it for a kkk k26 stock turbo ,for me it works better,lower rpm boost got better and its sounds beautiful
Ditto alda maxed and the factory kkk26 turbo any you've got great power by 2k
my dads 84 300d was a rocket out of the lights to about 40mph I also had the non EGR manifolds on it for him
1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
(11-01-2013, 04:33 PM)willbhere4u(10-31-2013, 04:42 PM)carlitosgy6 if you max the alda you will get faster boost and more low end torque,i was using a garret stock turbo and i replaced it for a kkk k26 stock turbo ,for me it works better,lower rpm boost got better and its sounds beautiful
Ditto alda maxed and the factory kkk26 turbo any you've got great power by 2k
i feel a difference accelerating from 70 to 80,it takes longer but before that i just feel it better
carlitosgy6
11-02-2013, 11:13 AM #23(11-01-2013, 04:33 PM)willbhere4u(10-31-2013, 04:42 PM)carlitosgy6 if you max the alda you will get faster boost and more low end torque,i was using a garret stock turbo and i replaced it for a kkk k26 stock turbo ,for me it works better,lower rpm boost got better and its sounds beautiful
Ditto alda maxed and the factory kkk26 turbo any you've got great power by 2k
i feel a difference accelerating from 70 to 80,it takes longer but before that i just feel it better
(10-24-2013, 05:59 PM)aaa GT2256v sounds like what you're looking for. Small easy to find VNT turbo (from the Sprinter vans).
Whats your tranmission setup? With the an automatic mercedes transmission I would simply use the higher-stall torque converter which lets the stock turbo spool up easily. Got a boost gauge to see what your turbo is doing now?
I love the high stall (25-2700 RPM) converter!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
11-15-2013, 05:06 AM #24(10-24-2013, 05:59 PM)aaa GT2256v sounds like what you're looking for. Small easy to find VNT turbo (from the Sprinter vans).
Whats your tranmission setup? With the an automatic mercedes transmission I would simply use the higher-stall torque converter which lets the stock turbo spool up easily. Got a boost gauge to see what your turbo is doing now?
I love the high stall (25-2700 RPM) converter!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
DirtDiesel
11-15-2013, 02:16 PM #25has anybody tried a quick spool valve and do they work?
LiL Micky
(11-15-2013, 02:16 PM)DirtDiesel has anybody tried a quick spool valve and do they work?
Quick spool valves only work on divided housing turbos. They shut exhaust off one scroll of the turbine and divert it to the larger side of the turbine wheel. As far as I know all the turbos discusses in this thread are open scroll
'82 300D -3" straight pipe, ALDA deleted, 3in1 glowshift gauge, HX30, egr-less manifold, A/W intercooler
'14 Ram 6.7l cummins -G56 handshaker, wishing it was deleted
(11-15-2013, 02:16 PM)DirtDiesel has anybody tried a quick spool valve and do they work?
Quick spool valves only work on divided housing turbos. They shut exhaust off one scroll of the turbine and divert it to the larger side of the turbine wheel. As far as I know all the turbos discusses in this thread are open scroll
'82 300D -3" straight pipe, ALDA deleted, 3in1 glowshift gauge, HX30, egr-less manifold, A/W intercooler
'14 Ram 6.7l cummins -G56 handshaker, wishing it was deleted
16 Guest(s)
16 Guest(s)