Superpump elements now for sale
Superpump elements now for sale
05-28-2014, 02:54 AM
#1
8,0mm 240-250cc 650:- SEK ( 70Euro)/pc
7,5mm 140-150cc 500:- SEK ( 55Euro)/pc
Gasket kit 5-6cyl 130SEK ( 14Euro)/pc
Gasket kit RSF Governor 130:-SEK ( 14Euro)/pc
Outside ALDA 1000:- SEK (110Euro) /pc
Pump must up in bench for calibration after swap, just change elements dont work.
Place order at dieselmeken@telia.com
For shipping cost I need name, adress, zipcode, phonenumber
Price include Swedih tax,
dieselmeken
05-28-2014, 02:54 AM #1
8,0mm 240-250cc 650:- SEK ( 70Euro)/pc
7,5mm 140-150cc 500:- SEK ( 55Euro)/pc
Gasket kit 5-6cyl 130SEK ( 14Euro)/pc
Gasket kit RSF Governor 130:-SEK ( 14Euro)/pc
Outside ALDA 1000:- SEK (110Euro) /pc
Pump must up in bench for calibration after swap, just change elements dont work.
Place order at dieselmeken@telia.com
For shipping cost I need name, adress, zipcode, phonenumber
Price include Swedih tax,
05-28-2014, 08:30 AM
#2
M series, 60x engines
I suppose old DV will work fine with these..
handy video
.
500SEC euro gen II powered by OM617a stolen from 84 300SD .... with 280se transmission now
----------------------------------------------------------
.
/
M series, 60x engines
I suppose old DV will work fine with these..
handy video
.
500SEC euro gen II powered by OM617a stolen from 84 300SD .... with 280se transmission now
----------------------------------------------------------
.
05-29-2014, 09:34 PM
#3
-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
05-29-2014, 09:34 PM #3If you decide to start doing MW pump elements do you think you would sell those as well?
-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
05-30-2014, 01:22 AM
#4
(05-29-2014, 09:34 PM)sassparilla_kid If you decide to start doing MW pump elements do you think you would sell those as well?Ofcourse, a Kit kontaining elements, gasket kit, watercut baseplate etc is on its way, Have to test out the MW Project pump first, and that is now done with good result.
dieselmeken
05-30-2014, 01:22 AM #4(05-29-2014, 09:34 PM)sassparilla_kid If you decide to start doing MW pump elements do you think you would sell those as well?Ofcourse, a Kit kontaining elements, gasket kit, watercut baseplate etc is on its way, Have to test out the MW Project pump first, and that is now done with good result.
06-25-2014, 10:00 AM
#5
I have a local bosch guy who is willing to install them - he'll just have to do the calibration to get everything to work?
1991 350SDL, burning oil and slow
1991 500SL, yet another project car
1984 190D, swapped 3.6 m104 with a megasquirt
how much for a kit?
I have a local bosch guy who is willing to install them - he'll just have to do the calibration to get everything to work?
1991 350SDL, burning oil and slow
1991 500SL, yet another project car
1984 190D, swapped 3.6 m104 with a megasquirt
06-25-2014, 10:39 AM
#6
(06-25-2014, 10:00 AM)yatzee how much for a kit?7,5 or 8,0mm? Price is at top of topic
I have a local bosch guy who is willing to install them - he'll just have to do the calibration to get everything to work?
dieselmeken
06-25-2014, 10:39 AM #6(06-25-2014, 10:00 AM)yatzee how much for a kit?7,5 or 8,0mm? Price is at top of topic
I have a local bosch guy who is willing to install them - he'll just have to do the calibration to get everything to work?
06-25-2014, 10:42 AM
#7
(06-25-2014, 10:39 AM)dieselmeken(06-25-2014, 10:00 AM)yatzee how much for a kit?7,5 or 8,0mm? Price is at top of topic
I have a local bosch guy who is willing to install them - he'll just have to do the calibration to get everything to work?
7.5mm, was just wondering if you'd do 1 price for everything we'd need
1991 350SDL, burning oil and slow
1991 500SL, yet another project car
1984 190D, swapped 3.6 m104 with a megasquirt
(06-25-2014, 10:39 AM)dieselmeken(06-25-2014, 10:00 AM)yatzee how much for a kit?7,5 or 8,0mm? Price is at top of topic
I have a local bosch guy who is willing to install them - he'll just have to do the calibration to get everything to work?
7.5mm, was just wondering if you'd do 1 price for everything we'd need
1991 350SDL, burning oil and slow
1991 500SL, yet another project car
1984 190D, swapped 3.6 m104 with a megasquirt
08-07-2014, 03:27 AM
#9
Also what size do you recommend for a OM605 running an hx35?
I may in the future compound the HX35 with an HX52, I already have both turbos but I think compounding is a long way off.
This post was last modified: 08-07-2014, 04:57 AM by Eric78.
Do these require machining of the pump to install or will they go straight in?
Also what size do you recommend for a OM605 running an hx35?
I may in the future compound the HX35 with an HX52, I already have both turbos but I think compounding is a long way off.
08-08-2014, 03:43 AM
#11
(08-07-2014, 04:42 AM)dieselmeken Fits perfect, needs calibration in testbench.
Hi dieselmeken,
My new pump have shipped to your US installer.
Regards,
1994 W140 S350 TD
OM603.971
H&R Sports springs/Bilstein HD, AMG Monoblock f/18x8.5 r/18x9.5, ALDA delete
09-01-2014, 12:37 AM
#16
(08-29-2014, 03:38 AM)silverzx Out of curiosity do these work well in the OM605 semi electronic pump?Yes, see my youtubechannel, there is a clip there showing these elements in a OM606 EDC pump
dieselmeken
09-01-2014, 12:37 AM #16(08-29-2014, 03:38 AM)silverzx Out of curiosity do these work well in the OM605 semi electronic pump?Yes, see my youtubechannel, there is a clip there showing these elements in a OM606 EDC pump
Users browsing this thread:
25 Guest(s)
25 Guest(s)
Users browsing this thread:
25 Guest(s)
25 Guest(s)