Is it possible to control edc pump without bosch head?
Is it possible to control edc pump without bosch head?
08-20-2014, 05:24 PM
#2
(08-19-2014, 02:45 PM)awk Hey!In a crude sense, yes you can. However, to get any meaningful control of fuel delivery you will need to monitor the position feedback line and adjust the drive current to get the fuel control rod to stop in the spot you want. It isn't as simple as apply X-volts and get Y-grams of fuel.
Can anyone tell me if it is possible to control edc pump just by giving voltage straight to governor?
Thanks
(08-19-2014, 02:45 PM)awk Hey!In a crude sense, yes you can. However, to get any meaningful control of fuel delivery you will need to monitor the position feedback line and adjust the drive current to get the fuel control rod to stop in the spot you want. It isn't as simple as apply X-volts and get Y-grams of fuel.
Can anyone tell me if it is possible to control edc pump just by giving voltage straight to governor?
Thanks
08-21-2014, 05:36 PM
#4
This post was last modified: 08-21-2014, 05:37 PM by baldur.
Baldur Gislason
No you need a governor program that controls rack position in closed loop and senses engine speed at the very least to be able to get an idle. I am working on such a swap myself but it won't be running for another couple months at least. I have done most of the design work, but need to get some boards printed and write the control code.
Baldur Gislason
08-22-2014, 01:19 PM
#5
Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
Simpler=Better
08-22-2014, 01:19 PM #5Is there a way to get it idling crudely? I have a 606 on the stand but no ecu and want to test fire it.
Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
08-22-2014, 07:33 PM
#6
(08-22-2014, 01:19 PM)Simpler=Better Is there a way to get it idling crudely? I have a 606 on the stand but no ecu and want to test fire it.Measure voltage across the driven coil on an idling OM606 and then apply the same voltage to your IP. You will probably need to up the voltage a bit during cranking to get enough fuel. Make sure you have a fast and foolproof way of disconnecting the power, it can over-rev very quickly.
(08-22-2014, 01:19 PM)Simpler=Better Is there a way to get it idling crudely? I have a 606 on the stand but no ecu and want to test fire it.Measure voltage across the driven coil on an idling OM606 and then apply the same voltage to your IP. You will probably need to up the voltage a bit during cranking to get enough fuel. Make sure you have a fast and foolproof way of disconnecting the power, it can over-rev very quickly.
08-23-2014, 06:53 PM
#8
Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
Simpler=Better
08-23-2014, 06:53 PM #8Thanks, I'll play with it
Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
Users browsing this thread:
4 Guest(s)
4 Guest(s)
Users browsing this thread:
4 Guest(s)
4 Guest(s)