VGT Turbos, intercooler, silicone hoses, fans
VGT Turbos, intercooler, silicone hoses, fans
What I've got:
* 2 Garret GT22V turbos (servo actuated). These should be considered cores for doing a rebuild (one visibly has sand in it).
* A small aluminum intercooler (it's one of these: Universal 16 5"x11"X2 5" Top Mount Exit JDM Aluminum Intercooler | eBay )
* Various silicone elbows, stainless couplers, and stainless clamps
* 3 thermocouples
* 2 electric fans (one used), with mounting kits
* Intake manifold from a turbocharged OM617
* Intake manifold from a naturally aspirated OM617
* Amsoil Ea (nanofiber) air filter
In short, if you've been considering throwing a VGT + intercooler onto your OM617, this set of parts will get you started.
Probably the biggest stumbling block would be finding / creating an electronic controller for the turbo's servo. I got to the point where I had an arduino-based proof of concept working: see Garrett 712120 VNT Hella 6NW 008 412 actuator.
I'd prefer to see these parts to go a crazy mercedes enthusiast, rather than some random craigslister.
I'm MUCH more interested in getting rid of these parts than in recovering anything near what I've spent. If you are near Austin, TX, make me an offer!
![[Image: nHqk8b8.jpg]](http://i.imgur.com/nHqk8b8.jpg)
![[Image: 42bexT9.jpg]](http://i.imgur.com/42bexT9.jpg)
![[Image: Q46vwix.jpg]](http://i.imgur.com/Q46vwix.jpg)
![[Image: gwras7F.jpg]](http://i.imgur.com/gwras7F.jpg)
As my GM-Benz project vehicle is no more, I'm getting rid of old parts for a never completed VGT turbo + intercooler installation.
What I've got:
* 2 Garret GT22V turbos (servo actuated). These should be considered cores for doing a rebuild (one visibly has sand in it).
* A small aluminum intercooler (it's one of these: Universal 16 5"x11"X2 5" Top Mount Exit JDM Aluminum Intercooler | eBay )
* Various silicone elbows, stainless couplers, and stainless clamps
* 3 thermocouples
* 2 electric fans (one used), with mounting kits
* Intake manifold from a turbocharged OM617
* Intake manifold from a naturally aspirated OM617
* Amsoil Ea (nanofiber) air filter
In short, if you've been considering throwing a VGT + intercooler onto your OM617, this set of parts will get you started.
Probably the biggest stumbling block would be finding / creating an electronic controller for the turbo's servo. I got to the point where I had an arduino-based proof of concept working: see Garrett 712120 VNT Hella 6NW 008 412 actuator.
I'd prefer to see these parts to go a crazy mercedes enthusiast, rather than some random craigslister.
I'm MUCH more interested in getting rid of these parts than in recovering anything near what I've spent. If you are near Austin, TX, make me an offer!
1987 Mazda B2200 "outlaw" **planning phase** Chevy 283, Power Pack heads, Edelbrock carb and intake, turbo 350 trans
1985 Mercedes 300D stock for now
Would you be pissed if they went to a crazy Mercedes enthusiast that wanted to use them in a non Mercedes build?
1987 Mazda B2200 "outlaw" **planning phase** Chevy 283, Power Pack heads, Edelbrock carb and intake, turbo 350 trans
1985 Mercedes 300D stock for now
1 Guest(s)
1 Guest(s)