h20 injection for cleansing purposes
h20 injection for cleansing purposes
Here's the idea:
Inject water to clean the pistons and PC's, primarily. I have this 190D that I just put a new headgasket on and the inside is a mess b/c some PO was burning all sorts of garbage straight from the tank.
I want to inject water to clean it up once its running. Not for performance on a regular basis so much as a quick mod to get the inside back to normal.
sorry, no pics... but 2 of the 4 PC's were 40% completely clogged. They have been reamed and the head is back on already.
So far, it seems I should inject a fine mist slightly above idle at operating temperature.
any other details???
totaldisaster
11-11-2009, 03:04 AM #1Its kinda maintenance,, but not orthodox. I posted this elsewhere, but got bad feedback.
Here's the idea:
Inject water to clean the pistons and PC's, primarily. I have this 190D that I just put a new headgasket on and the inside is a mess b/c some PO was burning all sorts of garbage straight from the tank.
I want to inject water to clean it up once its running. Not for performance on a regular basis so much as a quick mod to get the inside back to normal.
sorry, no pics... but 2 of the 4 PC's were 40% completely clogged. They have been reamed and the head is back on already.
So far, it seems I should inject a fine mist slightly above idle at operating temperature.
any other details???
A buddy of mine did it to an old 12 valve Cummins 6BT several years ago. I don't remember all of the details but he said it worked quite well. I know he used a hot water pressure washer and held it back from the intake several feet, as the source of H2O injection. He said he was amazed at all of the crap that came out of the tail pipe.
1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
11-11-2009, 11:56 AM #4On gassers we use to get them up to temp makes the water in to steem!!!! and we would use a carb jet in the end of a vaccunme hose in a boddle of water and let it suck it up under vaccume slowly!!!! you dont want to to water lock it with too much water and bend rods!!!! it works well we would let it suck up 1 gal of water over like a 1/2-1 hr period then drive it for a distance afterwards!!!!
1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
(11-11-2009, 01:11 PM)GREASY_BEAST You might want to change the oil after doing this.
Why? Water in the oil is not overly unusual, a good high way drive will burn it all off.
1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
(11-11-2009, 01:11 PM)GREASY_BEAST You might want to change the oil after doing this.
Why? Water in the oil is not overly unusual, a good high way drive will burn it all off.
1987 300D Sturmmachine
1991 300D Nearly Perfect
1985 300D Weekend/Camping/Dog car
1974 L508D Motoroam Monarch "NightMare"
OBK #42
ForcedInduction
11-11-2009, 03:21 PM
#7
Thats why MB changed the oil cooler thermostat from 95*c to 110*c, boil off moisture in the oil.
CID Vicious
11-18-2009, 07:59 PM #8Seafoam does the same thing and there's zero risk of hydrolocking the motor with it. I've seen it used on a variety of cars and it works.
(11-18-2009, 07:59 PM)CID Vicious Seafoam does the same thing and there's zero risk of hydrolocking the motor
Hydrolocking isn't the concern when spraying a combustible fluid into the intake of a diesel.
ForcedInduction
11-19-2009, 12:24 AM
#9
(11-18-2009, 07:59 PM)CID Vicious Seafoam does the same thing and there's zero risk of hydrolocking the motor
Hydrolocking isn't the concern when spraying a combustible fluid into the intake of a diesel.
4 Guest(s)
4 Guest(s)