Gearbox Controller 722.6
Gearbox Controller 722.6
01-08-2016, 03:38 PM
#1
Can somebody solution for the fixing ( I thinking about somthin like box) of this controller?
And the number (gearlever) sign can I buy somewere box/frame?
Offroadddieselhu
offroaddieselhu
01-08-2016, 03:38 PM #1Hello,
Can somebody solution for the fixing ( I thinking about somthin like box) of this controller?
And the number (gearlever) sign can I buy somewere box/frame?
Offroadddieselhu
01-15-2016, 11:51 AM
#2
Or are you looking for a full control solution ? I think olefejer has the market on this setup and I think it does have indication of gear select as well.
W123 Mods: 4 speed ** manual climate control ** '85 Kalitucky intake ** manual windows & full tint ** Euro headlights retrofit w/bixenon projectors ** 4 brake light mod ** Vogtland 50mm drop front & Lesjofors S600 drop rear springs ** 16" rims ** late w126 brake spindles, rotors & calipers ** full suspension rehab ** Bilstein HDs ** AL129X alternator & 1/0 starter and charging cables ** 300GD clutch/flywheel ** AFCO 80103N radiator & Earl's 41610 oil cooler ** custom block-off plate, remote oil filter & t-stat ** MW IP w/ tomnik's 6.5mm 'Holly' elements **
S124 Mods: 400E Rear subframe ** SL600 Brakes ** Late 300E 210mm diff ** SLK230 6 speed ** 17" CLK rims ** Vented RF Fender ** Facelift Hood, Headlights, and Lower Cladding **
OBK# 62
SurfRodder
01-15-2016, 11:51 AM #2so you're looking for a mounting box for the controller and a gear position indication to install this transmission in another car?
Or are you looking for a full control solution ? I think olefejer has the market on this setup and I think it does have indication of gear select as well.
W123 Mods: 4 speed ** manual climate control ** '85 Kalitucky intake ** manual windows & full tint ** Euro headlights retrofit w/bixenon projectors ** 4 brake light mod ** Vogtland 50mm drop front & Lesjofors S600 drop rear springs ** 16" rims ** late w126 brake spindles, rotors & calipers ** full suspension rehab ** Bilstein HDs ** AL129X alternator & 1/0 starter and charging cables ** 300GD clutch/flywheel ** AFCO 80103N radiator & Earl's 41610 oil cooler ** custom block-off plate, remote oil filter & t-stat ** MW IP w/ tomnik's 6.5mm 'Holly' elements **
S124 Mods: 400E Rear subframe ** SL600 Brakes ** Late 300E 210mm diff ** SLK230 6 speed ** 17" CLK rims ** Vented RF Fender ** Facelift Hood, Headlights, and Lower Cladding **
OBK# 62
01-15-2016, 05:33 PM
#3
I re-read, and think you mean like a mounting bezel for the displays?
would be a real simple job for someone with a 3d printer, and i'm sure others would buy them
would be a real simple job for someone with a 3d printer, and i'm sure others would buy them
---
W639 Vito OM606 + 722.6 STD - in progress
Current progress: engine in, gearbox in, bumper bar modified to accept w210 radiator, audi electric fan, very tight squeeze, interior stripped out ready for new seats (w211) and custom dash with w211 clocks controlled by arduino with split fuel gauge covering main tank and auxiliary for Veg Oil ...
- DSL1 ECU for Electronic OM606 Pump (currently fitting wiring)
Next; 722.6 Controller, HX40 with homemade manifold, Air-to-water intercooler, homemade exhaust, MOT.... One day!
I re-read, and think you mean like a mounting bezel for the displays?
would be a real simple job for someone with a 3d printer, and i'm sure others would buy them
would be a real simple job for someone with a 3d printer, and i'm sure others would buy them
---
W639 Vito OM606 + 722.6 STD - in progress
Current progress: engine in, gearbox in, bumper bar modified to accept w210 radiator, audi electric fan, very tight squeeze, interior stripped out ready for new seats (w211) and custom dash with w211 clocks controlled by arduino with split fuel gauge covering main tank and auxiliary for Veg Oil ...
- DSL1 ECU for Electronic OM606 Pump (currently fitting wiring)
Next; 722.6 Controller, HX40 with homemade manifold, Air-to-water intercooler, homemade exhaust, MOT.... One day!
01-16-2016, 06:45 AM
#4
(01-15-2016, 05:33 PM)mcwfxxI re-read, and think you mean like a mounting bezel for the displays?
would be a real simple job for someone with a 3d printer, and i'm sure others would buy them
Hi,
Yes, I'm looking for that (sory I haven't known that expression)
Offroaddieselhu
offroaddieselhu
01-16-2016, 06:45 AM #4(01-15-2016, 05:33 PM)mcwfxxI re-read, and think you mean like a mounting bezel for the displays?
would be a real simple job for someone with a 3d printer, and i'm sure others would buy them
Hi,
Yes, I'm looking for that (sory I haven't known that expression)
Offroaddieselhu
Users browsing this thread:
5 Guest(s)
5 Guest(s)
Users browsing this thread:
5 Guest(s)
5 Guest(s)