STD Tuning Engine hx27 turbo flange

hx27 turbo flange

hx27 turbo flange

 View a Printable Version
 
  • 0 Vote(s) - 0 Average
 
LewisG95
Find
K26-2

39
06-29-2016, 04:30 AM #1
Reply
Reply
Hi, 

I am after one of these flanges: 

   

Would anyone know where I could get one of these? or would anyone be able to make me one up at all?

Thanks
LewisG95
06-29-2016, 04:30 AM #1

Hi, 

I am after one of these flanges: 

   

Would anyone know where I could get one of these? or would anyone be able to make me one up at all?

Thanks

Reply
Reply
hents99
Website Find
GT2256V

157
06-29-2016, 05:03 AM #2
Reply
Reply
I could provide DXF drawing if you like. You can easily send it to water/laser cut.

Edit: I made drawing for you. It`s very good drawing you attached. 

   
This post was last modified: 06-29-2016, 05:16 AM by hents99.
Attached Files
.dxf
HX27_outlet.DXF
Size: 20.45 KB / Downloads: 463
------------------------------------------------------------------------
www.elbe.ee - MB performance parts.
hents99
06-29-2016, 05:03 AM #2

I could provide DXF drawing if you like. You can easily send it to water/laser cut.

Edit: I made drawing for you. It`s very good drawing you attached. 

   

Attached Files
.dxf
HX27_outlet.DXF
Size: 20.45 KB / Downloads: 463
------------------------------------------------------------------------
www.elbe.ee - MB performance parts.

Reply
Reply
LewisG95
Find
K26-2

39
06-29-2016, 06:06 AM #3
Reply
Reply
Thanks for that mate.

I have already tried to get a quote from a local laser cutting company but they wanted £70 for a one off which I think is a bit expensive.

I would only be looking to spend £30ish on one really.

Thanks
LewisG95
06-29-2016, 06:06 AM #3

Thanks for that mate.

I have already tried to get a quote from a local laser cutting company but they wanted £70 for a one off which I think is a bit expensive.

I would only be looking to spend £30ish on one really.

Thanks

Reply
Reply
hents99
Website Find
GT2256V

157
06-29-2016, 06:09 AM #4
Reply
Reply
Wow. CNC mill won`t charge that much.....try another workshop. It must be around 5-10 pounds if you have the drawing.
------------------------------------------------------------------------
www.elbe.ee - MB performance parts.
hents99
06-29-2016, 06:09 AM #4

Wow. CNC mill won`t charge that much.....try another workshop. It must be around 5-10 pounds if you have the drawing.

------------------------------------------------------------------------
www.elbe.ee - MB performance parts.

Reply
Reply
JVance
Find
GTA2056V

92
06-30-2016, 11:04 PM #5
Reply
Reply
www.eurotrashmotorsports.com
JVance
06-30-2016, 11:04 PM #5

www.eurotrashmotorsports.com

Reply
Reply
Hario'
Find
C300TD Wagon (W202)

894
07-02-2016, 05:41 AM #6
Reply
Reply
Worse case make your own!



Installed:
OM606/722.6, big IC, W220 brakes.
Planned:
DIY manifold, compound, 722.6 controller, built IP.
[i]Less rust.. [/i]
Hario'
07-02-2016, 05:41 AM #6

Worse case make your own!




Installed:
OM606/722.6, big IC, W220 brakes.
Planned:
DIY manifold, compound, 722.6 controller, built IP.
[i]Less rust.. [/i]

Reply
Reply
bricktron
Find
'77 240D

174
07-02-2016, 07:33 PM #7
Reply
Reply
hents99, what a champ!
english red rat rod 1977 240D, OM617.952 burning B99.9, iron 4-speed & 2.88 diff, 195/60/R14 on alloys, 5mph bumpers, battery in the trunk, 25mm swaybar, 4x ECE H4 lamps, double brake lamps, deleted sunroof, export zoll & california blue plates




bricktron
07-02-2016, 07:33 PM #7

hents99, what a champ!

english red rat rod 1977 240D, OM617.952 burning B99.9, iron 4-speed & 2.88 diff, 195/60/R14 on alloys, 5mph bumpers, battery in the trunk, 25mm swaybar, 4x ECE H4 lamps, double brake lamps, deleted sunroof, export zoll & california blue plates




Reply
Reply
 View a Printable Version
 
  • 0 Vote(s) - 0 Average
Users browsing this thread:
 4 Guest(s)
Users browsing this thread:
 4 Guest(s)