STD Tuning Engine Engine maintenance prior to fitting

Engine maintenance prior to fitting

Engine maintenance prior to fitting

 View a Printable Version
 
  • 0 Vote(s) - 0 Average
 
Chopper746
Find
Naturally-aspirated

6
07-10-2016, 11:40 AM #1
Reply
Reply
Hi guys,

New to the forum have just got my hands on an om606 i am just wondering if there is anything i should change other than the obvious prior to fitment seals,water pump etc. I will be cleaning and painting it first and looking to run around 350bhp with reliability.

Thanks for any advice.
Chopper746
07-10-2016, 11:40 AM #1

Hi guys,

New to the forum have just got my hands on an om606 i am just wondering if there is anything i should change other than the obvious prior to fitment seals,water pump etc. I will be cleaning and painting it first and looking to run around 350bhp with reliability.

Thanks for any advice.

Reply
Reply
zeeman
Find
Holset

444
07-10-2016, 11:45 AM #2
Reply
Reply
(07-10-2016, 11:40 AM)Chopper746 Hi guys,

New to the forum have just got my hands on an om606 i am just wondering if there is anything i should change other than the obvious prior to fitment seals,water pump etc. I will be cleaning and painting it first and looking to run around 350bhp with reliability.

Thanks for any advice.

Another item to check is the plastic holders that hold the injector lines. They break and the lines rub on the intake. Also the injector return lines. Good idea to replace the glowplugs if it is a high mile engine.
zeeman
07-10-2016, 11:45 AM #2

(07-10-2016, 11:40 AM)Chopper746 Hi guys,

New to the forum have just got my hands on an om606 i am just wondering if there is anything i should change other than the obvious prior to fitment seals,water pump etc. I will be cleaning and painting it first and looking to run around 350bhp with reliability.

Thanks for any advice.

Another item to check is the plastic holders that hold the injector lines. They break and the lines rub on the intake. Also the injector return lines. Good idea to replace the glowplugs if it is a high mile engine.

Reply
Reply
Chopper746
Find
Naturally-aspirated

6
07-10-2016, 12:01 PM #3
Reply
Reply
(07-10-2016, 11:45 AM)zeeman
(07-10-2016, 11:40 AM)Chopper746 Hi guys,

New to the forum have just got my hands on an om606 i am just wondering if there is anything i should change other than the obvious prior to fitment seals,water pump etc. I will be cleaning and painting it first and looking to run around 350bhp with reliability.

Thanks for any advice.

Another item to check is the plastic holders that hold the injector lines. They break and the lines rub on the intake. Also the injector return lines. Good idea to replace the glowplugs if it is a high mile engine.

Thanks for the reply ill put it on the list.
Chopper746
07-10-2016, 12:01 PM #3

(07-10-2016, 11:45 AM)zeeman
(07-10-2016, 11:40 AM)Chopper746 Hi guys,

New to the forum have just got my hands on an om606 i am just wondering if there is anything i should change other than the obvious prior to fitment seals,water pump etc. I will be cleaning and painting it first and looking to run around 350bhp with reliability.

Thanks for any advice.

Another item to check is the plastic holders that hold the injector lines. They break and the lines rub on the intake. Also the injector return lines. Good idea to replace the glowplugs if it is a high mile engine.

Thanks for the reply ill put it on the list.

Reply
Reply
AlanMcR
Find
mind - blown

400
07-11-2016, 01:02 PM #4
Reply
Reply
The glowplugs in an OM606 should only be replaced when the head is warm. Otherwise they will likely stick in the head and snap off. Then you will be sad.
AlanMcR
07-11-2016, 01:02 PM #4

The glowplugs in an OM606 should only be replaced when the head is warm. Otherwise they will likely stick in the head and snap off. Then you will be sad.

Reply
Reply
 View a Printable Version
 
  • 0 Vote(s) - 0 Average
Users browsing this thread:
 4 Guest(s)
Users browsing this thread:
 4 Guest(s)