OM605 manual pump + oil cooler
OM605 manual pump + oil cooler
09-22-2016, 04:50 PM
#1
I'm building a W124 with a 605 at the moment and i've got a question about oil coolers. I'm using a KKK turbo from an E300 so i'm not going to be making huge power. Obviously the 605 comes with the oil/water cooler, but with the manual pump on this won't fit. I have a 606 n/a oil filter housing which does fit but this means I don't have an oil cooler.
What is the best way to get round this? So far i have 3 options;
- 606 n/a housing and no cooler (probably overheat the oil)
- 605 housing with fittings welded on in place of the standard oil/water cooler (with there being no thermostat on it, could this cause warm up issues with the oil?)
- Make a sandwich plate, remote oil filter and cooler (pain in the a*se)
![[Image: 14359080_10157338011295276_3162859479113...e=5885C2F8]](https://scontent-lhr3-1.xx.fbcdn.net/v/t1.0-9/14359080_10157338011295276_3162859479113008873_n.jpg?oh=c9aee54924f9592cdfae862870236ddb&oe=5885C2F8)
Thanks!
This post was last modified: 09-22-2016, 06:20 PM by Nev.
Good evening, this is my first post so hello everyone!
I'm building a W124 with a 605 at the moment and i've got a question about oil coolers. I'm using a KKK turbo from an E300 so i'm not going to be making huge power. Obviously the 605 comes with the oil/water cooler, but with the manual pump on this won't fit. I have a 606 n/a oil filter housing which does fit but this means I don't have an oil cooler.
What is the best way to get round this? So far i have 3 options;
- 606 n/a housing and no cooler (probably overheat the oil)
- 605 housing with fittings welded on in place of the standard oil/water cooler (with there being no thermostat on it, could this cause warm up issues with the oil?)
- Make a sandwich plate, remote oil filter and cooler (pain in the a*se)
Thanks!
09-23-2016, 10:17 AM
#4
(09-23-2016, 01:38 AM)Nev Its from Luke at DieselPumpUK. If I took the rear module off it and made a plate it would fit, but as it is it doesn't.
Yea mines from Luke. But it does fit. Well it's all in anyway. It is close tho. Il take a pic.
Mitsubishi L200 manual om605
7.5mm Bosch 044 fed pump
Borgwarner S200
(09-23-2016, 01:38 AM)Nev Its from Luke at DieselPumpUK. If I took the rear module off it and made a plate it would fit, but as it is it doesn't.
Yea mines from Luke. But it does fit. Well it's all in anyway. It is close tho. Il take a pic.
Mitsubishi L200 manual om605
7.5mm Bosch 044 fed pump
Borgwarner S200
11-02-2016, 11:46 AM
#7
(09-23-2016, 01:38 AM)Nev Its from Luke at DieselPumpUK. If I took the rear module off it and made a plate it would fit, but as it is it doesn't.
606.962 filter housing with remote oil cooler take off already built in?
Installed:
OM606/722.6, big IC, W220 brakes.
Planned:
DIY manifold, compound, 722.6 controller, built IP.
[i]Less rust.. [/i]
(09-23-2016, 01:38 AM)Nev Its from Luke at DieselPumpUK. If I took the rear module off it and made a plate it would fit, but as it is it doesn't.
606.962 filter housing with remote oil cooler take off already built in?
Installed:
OM606/722.6, big IC, W220 brakes.
Planned:
DIY manifold, compound, 722.6 controller, built IP.
[i]Less rust.. [/i]
Users browsing this thread:
7 Guest(s)
7 Guest(s)
Users browsing this thread:
7 Guest(s)
7 Guest(s)