Ram/Cold Air intake
Ram/Cold Air intake
10-13-2012, 06:23 PM
#1
thegooch27
10-13-2012, 06:23 PM #1I was able to put this together for around $85.00. It's a K&N Apollo universal intake. I also had to buy a 60 Degree silicone reducer elbow and I also run the prefilter. There is a more turbo noise with this setup but I like it!
10-14-2012, 10:19 AM
#2
Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
Simpler=Better
10-14-2012, 10:19 AM #2I like it
Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
10-15-2012, 11:05 AM
#4
(10-15-2012, 04:50 AM)cho .http://www.knfilters.com/universal/apollo.htm
looks good
looks small
what's the CFM?
.
Good for up to 350BHP...
thegooch27
10-15-2012, 11:05 AM #4(10-15-2012, 04:50 AM)cho .http://www.knfilters.com/universal/apollo.htm
looks good
looks small
what's the CFM?
.
Good for up to 350BHP...
10-16-2012, 06:03 AM
#5
(10-15-2012, 11:05 AM)thegooch27(10-15-2012, 04:50 AM)cho .http://www.knfilters.com/universal/apollo.htm
looks good
looks small
what's the CFM?
.
Good for up to 350BHP...
in that case:
good job good job
.
500SEC euro gen II powered by OM617a stolen from 84 300SD .... with 280se transmission now
----------------------------------------------------------
.
(10-15-2012, 11:05 AM)thegooch27(10-15-2012, 04:50 AM)cho .http://www.knfilters.com/universal/apollo.htm
looks good
looks small
what's the CFM?
.
Good for up to 350BHP...
in that case:
good job good job
.
500SEC euro gen II powered by OM617a stolen from 84 300SD .... with 280se transmission now
----------------------------------------------------------
.
10-21-2012, 02:53 PM
#6
'82 300D -3" straight pipe, ALDA deleted, 3in1 glowshift gauge, HX30, egr-less manifold, A/W intercooler
'14 Ram 6.7l cummins -G56 handshaker, wishing it was deleted
This looks awesome, and I was thinking about doing it to my car. You said you had about $85 in it? The cheapest filter i have found is $99. Cool idea
'82 300D -3" straight pipe, ALDA deleted, 3in1 glowshift gauge, HX30, egr-less manifold, A/W intercooler
'14 Ram 6.7l cummins -G56 handshaker, wishing it was deleted
10-21-2012, 08:24 PM
#7
DirtDiesel
10-21-2012, 08:24 PM #7I dont know if you like AFE filters but you can build your own for roughly $50 just my input
08-22-2017, 11:34 PM
#9
This post was last modified: 08-22-2017, 11:35 PM by NZScott.
1978 300D, 373,000km... OM617.912 with a Holset HX30W, 7.5mm IP, 711.113 5 speed (project car, 7 years off the road and counting ;/)
1977 250 270,000km (parts car)
1977 300D (ex 280) 500,000km
1981 240D 498,000
1975 HJ45 ???,000
2001 2.8TD Rodeo 4x2 - 456,000 - DD
First time for me seeing this thread and first impression is it's rather tiny for a diesel. 350 hp might be plucked out of thin air for a petrol engine which doesn't need as much air mass per hp as our IDIs do. And did I mention K&N filters are shit? Lol
1978 300D, 373,000km... OM617.912 with a Holset HX30W, 7.5mm IP, 711.113 5 speed (project car, 7 years off the road and counting ;/)
1977 250 270,000km (parts car)
1977 300D (ex 280) 500,000km
1981 240D 498,000
1975 HJ45 ???,000
2001 2.8TD Rodeo 4x2 - 456,000 - DD
08-23-2017, 05:24 AM
#10
(08-22-2017, 11:34 PM)NZScott First time for me seeing this thread and first impression is it's rather tiny for a diesel. 350 hp might be plucked out of thin air for a petrol engine which doesn't need as much air mass per hp as our IDIs do. And did I mention K&N filters are shit? Lol
This!!
Why on earth you'd want to fit one is beyond me. Especially in a land rover type vehicle, they just let allllll the crap through.
(08-22-2017, 11:34 PM)NZScott First time for me seeing this thread and first impression is it's rather tiny for a diesel. 350 hp might be plucked out of thin air for a petrol engine which doesn't need as much air mass per hp as our IDIs do. And did I mention K&N filters are shit? Lol
This!!
Why on earth you'd want to fit one is beyond me. Especially in a land rover type vehicle, they just let allllll the crap through.
08-23-2017, 11:25 AM
#11
(08-22-2017, 11:34 PM)NZScott First time for me seeing this thread and first impression is it's rather tiny for a diesel. 350 hp might be plucked out of thin air for a petrol engine which doesn't need as much air mass per hp as our IDIs do. And did I mention K&N filters are shit? Lol
(08-23-2017, 05:24 AM)ross(08-22-2017, 11:34 PM)NZScott First time for me seeing this thread and first impression is it's rather tiny for a diesel. 350 hp might be plucked out of thin air for a petrol engine which doesn't need as much air mass per hp as our IDIs do. And did I mention K&N filters are shit? Lol
This!!
Why on earth you'd want to fit one is beyond me. Especially in a land rover type vehicle, they just let allllll the crap through.
Thanks - haha glad I brought the thread back up then before I made a purchase!
What I thought was slick was the enclosed design where I could run the tubing from the snorkel to one side and then exit out to the turbo inlet.
I could always make something out of sheet aluminum but I'm so sick of fabrication work (been taking me ages to get the HX30 installed) that something "off the shelf" would make it easier for me.
If you guys have any suggestions please let me know - I would really appreciate it!
(08-22-2017, 11:34 PM)NZScott First time for me seeing this thread and first impression is it's rather tiny for a diesel. 350 hp might be plucked out of thin air for a petrol engine which doesn't need as much air mass per hp as our IDIs do. And did I mention K&N filters are shit? Lol
(08-23-2017, 05:24 AM)ross(08-22-2017, 11:34 PM)NZScott First time for me seeing this thread and first impression is it's rather tiny for a diesel. 350 hp might be plucked out of thin air for a petrol engine which doesn't need as much air mass per hp as our IDIs do. And did I mention K&N filters are shit? Lol
This!!
Why on earth you'd want to fit one is beyond me. Especially in a land rover type vehicle, they just let allllll the crap through.
Thanks - haha glad I brought the thread back up then before I made a purchase!
What I thought was slick was the enclosed design where I could run the tubing from the snorkel to one side and then exit out to the turbo inlet.
I could always make something out of sheet aluminum but I'm so sick of fabrication work (been taking me ages to get the HX30 installed) that something "off the shelf" would make it easier for me.
If you guys have any suggestions please let me know - I would really appreciate it!
08-24-2017, 07:44 AM
#13
(08-23-2017, 11:25 AM)don(08-22-2017, 11:34 PM)NZScott First time for me seeing this thread and first impression is it's rather tiny for a diesel. 350 hp might be plucked out of thin air for a petrol engine which doesn't need as much air mass per hp as our IDIs do. And did I mention K&N filters are shit? Lol
(08-23-2017, 05:24 AM)ross(08-22-2017, 11:34 PM)NZScott First time for me seeing this thread and first impression is it's rather tiny for a diesel. 350 hp might be plucked out of thin air for a petrol engine which doesn't need as much air mass per hp as our IDIs do. And did I mention K&N filters are shit? Lol
This!!
Why on earth you'd want to fit one is beyond me. Especially in a land rover type vehicle, they just let allllll the crap through.
Thanks - haha glad I brought the thread back up then before I made a purchase!
What I thought was slick was the enclosed design where I could run the tubing from the snorkel to one side and then exit out to the turbo inlet.
I could always make something out of sheet aluminum but I'm so sick of fabrication work (been taking me ages to get the HX30 installed) that something "off the shelf" would make it easier for me.
If you guys have any suggestions please let me know - I would really appreciate it!
Most Land Rover air boxes are probably all too small, BUT the defender v8 one is huge and should be plenty big enough!
This post was last modified: 08-24-2017, 07:45 AM by ross.
(08-23-2017, 11:25 AM)don(08-22-2017, 11:34 PM)NZScott First time for me seeing this thread and first impression is it's rather tiny for a diesel. 350 hp might be plucked out of thin air for a petrol engine which doesn't need as much air mass per hp as our IDIs do. And did I mention K&N filters are shit? Lol
(08-23-2017, 05:24 AM)ross(08-22-2017, 11:34 PM)NZScott First time for me seeing this thread and first impression is it's rather tiny for a diesel. 350 hp might be plucked out of thin air for a petrol engine which doesn't need as much air mass per hp as our IDIs do. And did I mention K&N filters are shit? Lol
This!!
Why on earth you'd want to fit one is beyond me. Especially in a land rover type vehicle, they just let allllll the crap through.
Thanks - haha glad I brought the thread back up then before I made a purchase!
What I thought was slick was the enclosed design where I could run the tubing from the snorkel to one side and then exit out to the turbo inlet.
I could always make something out of sheet aluminum but I'm so sick of fabrication work (been taking me ages to get the HX30 installed) that something "off the shelf" would make it easier for me.
If you guys have any suggestions please let me know - I would really appreciate it!
Most Land Rover air boxes are probably all too small, BUT the defender v8 one is huge and should be plenty big enough!
08-24-2017, 08:51 AM
#15
(08-24-2017, 07:44 AM)ross Most Land Rover air boxes are probably all too small, BUT the defender v8 one is huge and should be plenty big enough!
My brother in law has a parts RRC. I'll see if that has anything worthwhile. If it's made of steel I can modify it as I have a welder.
08-24-2017, 09:37 AM
#16
It should give adequate airflow.
One from a 85 W126 300SD recently has been mounted on my 83 W126 300SD.
This frees up space to install my non-EGR exhaust manifold and the longrunner W115 intake manifold.
Depending on your available room you may be able to fit a stock MB fender mounted air box.
It should give adequate airflow.
One from a 85 W126 300SD recently has been mounted on my 83 W126 300SD.
This frees up space to install my non-EGR exhaust manifold and the longrunner W115 intake manifold.
08-25-2017, 09:25 AM
#18
(08-24-2017, 09:52 AM)ross(08-24-2017, 08:51 AM)don My brother in law has a parts RRC. I'll see if that has anything worthwhile. If it's made of steel I can modify it as I have a welder.
From memory the RRC ones are quite small, but should work
If I can get a freebie one from my brother in law I might get a second one on eBay and seam weld them together to make something where a good size filter will fit.
(08-24-2017, 09:52 AM)ross(08-24-2017, 08:51 AM)don My brother in law has a parts RRC. I'll see if that has anything worthwhile. If it's made of steel I can modify it as I have a welder.
From memory the RRC ones are quite small, but should work
If I can get a freebie one from my brother in law I might get a second one on eBay and seam weld them together to make something where a good size filter will fit.
08-25-2017, 09:29 AM
#19
(08-24-2017, 09:37 AM)Alec300SD Depending on your available room you may be able to fit a stock MB fender mounted air box.
It should give adequate airflow.
One from a 85 W126 300SD recently has been mounted on my 83 W126 300SD.
This frees up space to install my non-EGR exhaust manifold and the longrunner W115 intake manifold.
Thanks - I might just do a cylinder style so air filter R&R will be (or should be) easier.
I like the different ideas tho!
(08-24-2017, 09:37 AM)Alec300SD Depending on your available room you may be able to fit a stock MB fender mounted air box.
It should give adequate airflow.
One from a 85 W126 300SD recently has been mounted on my 83 W126 300SD.
This frees up space to install my non-EGR exhaust manifold and the longrunner W115 intake manifold.
Thanks - I might just do a cylinder style so air filter R&R will be (or should be) easier.
I like the different ideas tho!
Users browsing this thread:
7 Guest(s)
7 Guest(s)
Users browsing this thread:
7 Guest(s)
7 Guest(s)