Oil catch can om606?
Oil catch can om606?
2005 CDI heavily modified 1984 300TD - Myna pump/TMIC/enlarged PC's/HX30Super/W126 II front brakes/Vogtland springs/EGT +Boost gauges/H4 Hella's
I use a gatorade bottle filled with fishing line; the tube goes all the way down to near the bottom and then a several smaller holes are drilled in the bottle near the top. The vapor has to filter thru the fishing line and it condenses on it. Make sure you have enough airflow/holes otherwise it'll choke your engine. I have to empty the bottle, well, never. Over 5 years and it had about 2 ounces of oil in it. This is on a modified OM617.
2005 CDI heavily modified 1984 300TD - Myna pump/TMIC/enlarged PC's/HX30Super/W126 II front brakes/Vogtland springs/EGT +Boost gauges/H4 Hella's
1978 300D, 373,000km... OM617.912 with a Holset HX30W, 7.5mm IP, 711.113 5 speed (project car, 7 years off the road and counting ;/)
1977 250 270,000km (parts car)
1977 300D (ex 280) 500,000km
1981 240D 498,000
1975 HJ45 ???,000
2001 2.8TD Rodeo 4x2 - 456,000 - DD
Also pools inside intercoolers nicely too?
1978 300D, 373,000km... OM617.912 with a Holset HX30W, 7.5mm IP, 711.113 5 speed (project car, 7 years off the road and counting ;/)
1977 250 270,000km (parts car)
1977 300D (ex 280) 500,000km
1981 240D 498,000
1975 HJ45 ???,000
2001 2.8TD Rodeo 4x2 - 456,000 - DD
(05-10-2018, 12:27 PM)AlanMcR There is way too much air flow to let anything more than a microscopic film of oil cling to the sides of the passages. Not a problem at all. Also, you get a free boost leak detector, since that film of oil will leak out anywhere that there is a boost leak.
Amen to that. That’s how I found my pin holes in my new ally air intake plenum
Mitsubishi L200 manual om605
7.5mm Bosch 044 fed pump
Borgwarner S200
(05-10-2018, 12:27 PM)AlanMcR There is way too much air flow to let anything more than a microscopic film of oil cling to the sides of the passages. Not a problem at all. Also, you get a free boost leak detector, since that film of oil will leak out anywhere that there is a boost leak.
Amen to that. That’s how I found my pin holes in my new ally air intake plenum
Mitsubishi L200 manual om605
7.5mm Bosch 044 fed pump
Borgwarner S200
1978 300D, 373,000km... OM617.912 with a Holset HX30W, 7.5mm IP, 711.113 5 speed (project car, 7 years off the road and counting ;/)
1977 250 270,000km (parts car)
1977 300D (ex 280) 500,000km
1981 240D 498,000
1975 HJ45 ???,000
2001 2.8TD Rodeo 4x2 - 456,000 - DD
Good point, I don't have an intercooler yet so think I'll shut up now
1978 300D, 373,000km... OM617.912 with a Holset HX30W, 7.5mm IP, 711.113 5 speed (project car, 7 years off the road and counting ;/)
1977 250 270,000km (parts car)
1977 300D (ex 280) 500,000km
1981 240D 498,000
1975 HJ45 ???,000
2001 2.8TD Rodeo 4x2 - 456,000 - DD
I think it will be one of those things where people are for it and some against it. I spoke to some local performance shops and again some were for and some against it. So I think I don't have a race car, I will save the cash and not run one and get a free boost leak detector.
3 Guest(s)
3 Guest(s)