A-pump. P-pump, M-pump and MW-pump governors
A-pump. P-pump, M-pump and MW-pump governors
I have been looking into this, but I cannot find any reliable answers without actually purchasing examples of these pumps, which is way too expensive for little old me to afford.
I know that the M-pump, MW-pump, A-pump and P-pump all use the RSV governor in certain applications. I also know that the M-pump and the P-pump used an EDC actuator (specifically, the M-pump on W210 OM605 and OM606).
I was wondering if either of these EDC actuators could fit onto an MW-pump. Or if somebody knows if any MW pumps were used with EDC, say as electric generators etc. Perhaps somebody knows the difference between the rear mounting faces of these pumps, where the governors bolt on to.
Thanks
PlaneCrazy
11-20-2018, 11:53 PM #1Greetings, all
I have been looking into this, but I cannot find any reliable answers without actually purchasing examples of these pumps, which is way too expensive for little old me to afford.
I know that the M-pump, MW-pump, A-pump and P-pump all use the RSV governor in certain applications. I also know that the M-pump and the P-pump used an EDC actuator (specifically, the M-pump on W210 OM605 and OM606).
I was wondering if either of these EDC actuators could fit onto an MW-pump. Or if somebody knows if any MW pumps were used with EDC, say as electric generators etc. Perhaps somebody knows the difference between the rear mounting faces of these pumps, where the governors bolt on to.
Thanks
1978 300D, 373,000km... OM617.912 with a Holset HX30W, 7.5mm IP, 711.113 5 speed (project car, 7 years off the road and counting ;/)
1977 250 270,000km (parts car)
1977 300D (ex 280) 500,000km
1981 240D 498,000
1975 HJ45 ???,000
2001 2.8TD Rodeo 4x2 - 456,000 - DD
You have a OM617 don't you? Or trying to fit onto a non MB engine? The EDC governor end should swap onto ya normal OM617 M pump...at least my Barrote built 7.5mm has a OM60x governor
1978 300D, 373,000km... OM617.912 with a Holset HX30W, 7.5mm IP, 711.113 5 speed (project car, 7 years off the road and counting ;/)
1977 250 270,000km (parts car)
1977 300D (ex 280) 500,000km
1981 240D 498,000
1975 HJ45 ???,000
2001 2.8TD Rodeo 4x2 - 456,000 - DD
1978 300D, 373,000km... OM617.912 with a Holset HX30W, 7.5mm IP, 711.113 5 speed (project car, 7 years off the road and counting ;/)
1977 250 270,000km (parts car)
1977 300D (ex 280) 500,000km
1981 240D 498,000
1975 HJ45 ???,000
2001 2.8TD Rodeo 4x2 - 456,000 - DD
Aha. Yep well there's not much to them....you could even make your own external electronic controller for an IP if one wished
1978 300D, 373,000km... OM617.912 with a Holset HX30W, 7.5mm IP, 711.113 5 speed (project car, 7 years off the road and counting ;/)
1977 250 270,000km (parts car)
1977 300D (ex 280) 500,000km
1981 240D 498,000
1975 HJ45 ???,000
2001 2.8TD Rodeo 4x2 - 456,000 - DD
https://www.youtube.com/watch?v=GYpSrADlzxA
85 300D om617: 8mm M pump 175cc 5200rpm, holset he221w @ 30psi, large A2W ic, compounds on the way.
you can bolt an edc tail housing onto a normal m pump with an adapter plate.
https://www.youtube.com/watch?v=GYpSrADlzxA
85 300D om617: 8mm M pump 175cc 5200rpm, holset he221w @ 30psi, large A2W ic, compounds on the way.
P are not EDC from my knowledge.
Anyhow why would anyone use a EDC governor in a MW?
M pumps use RSF governors wich are variable speed governors. RSV is a variable load governor , suitable only for industrial aplications.
RSQ are the governor from MW. RQV is another type of governor used in MW .
FD,
Powered by tractor fuel
EDC pumps are only M and H from the inlines.
P are not EDC from my knowledge.
Anyhow why would anyone use a EDC governor in a MW?
M pumps use RSF governors wich are variable speed governors. RSV is a variable load governor , suitable only for industrial aplications.
RSQ are the governor from MW. RQV is another type of governor used in MW .
FD,
Powered by tractor fuel
3 Guest(s)
3 Guest(s)