turbo oil leak - likely cause?
turbo oil leak - likely cause?
My rebuild project (1982 300GD with OM617NA) is progressing (albeit slowly). I am trying to cure a bad oil leak from the casing of the aftermarket turbo.
Any guesses what part of the turbo might be defective? Can anybody provide a cross-sectional drawing showing the innards of a basic 1980's turbo?
Many thanks, Adrian
Hi all
My rebuild project (1982 300GD with OM617NA) is progressing (albeit slowly). I am trying to cure a bad oil leak from the casing of the aftermarket turbo.
Any guesses what part of the turbo might be defective? Can anybody provide a cross-sectional drawing showing the innards of a basic 1980's turbo?
Many thanks, Adrian
Clean the area well, run it a few minutes and see exactly where its coming from. If it were a shaft seal leaking that bad your exhaust would be smoking a lot.
ForcedInduction
06-21-2010, 05:00 AM
#2
There are only 4 places it can leak oil; the oil inlet and drain connections and either end of the shaft.
Clean the area well, run it a few minutes and see exactly where its coming from. If it were a shaft seal leaking that bad your exhaust would be smoking a lot.
The oil seems to be coming from the casing joint, all the way around, and not from the oil hose connections. There is some smoke with the exhaust, to be sure. I am wondering if the turbo casing is not sealed then the oil may be escaping that way. Is this possible?
Thanks
Adrian
Thanks Forced,
The oil seems to be coming from the casing joint, all the way around, and not from the oil hose connections. There is some smoke with the exhaust, to be sure. I am wondering if the turbo casing is not sealed then the oil may be escaping that way. Is this possible?
Thanks
Adrian
1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
06-21-2010, 10:32 PM #4What kind of turbo do you have?
1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
ForcedInduction
06-22-2010, 04:47 AM
#5
The oil is coming from the shaft seal, the turbo needs rebuilt.
just ordered mine along with a bunch of other things.. cant wait
my car was smoking upon slight/medium acceleration and i knew the turbo needed rebuilding since it has 180k on the odo.
W116Lorinser
07-24-2010, 11:17 PM #7they have rebuild kit for $120 and change with free shipping and tools included so you dont have to compelety take the turbo out.
just ordered mine along with a bunch of other things.. cant wait
my car was smoking upon slight/medium acceleration and i knew the turbo needed rebuilding since it has 180k on the odo.
Also $120 is VERY expensive for a T3 kit, it shouldn't cost more than $35!
What "tools" do they include? $120 won't cover the cost of a calibrated torque wrench to assemble the shaft and no special tools are needed to remove the turbo leaving the turbine housing in place, just a 10mm socket and 13mm wrench.
ForcedInduction
07-24-2010, 11:24 PM
#8
A turbo can't be properly rebuilt by a home DIYer.
Also $120 is VERY expensive for a T3 kit, it shouldn't cost more than $35!
What "tools" do they include? $120 won't cover the cost of a calibrated torque wrench to assemble the shaft and no special tools are needed to remove the turbo leaving the turbine housing in place, just a 10mm socket and 13mm wrench.
It's a good time to clean every thing before you put it back together!
1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
07-27-2010, 11:56 AM #10Good luck with all of this work I hope it all works out!
It's a good time to clean every thing before you put it back together!
1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
6 Guest(s)
6 Guest(s)