Reverse rotation
Reverse rotation
01-18-2011, 07:00 AM
#1
Application 1975 Penn Yan Avenger flybridge.
Thankyou,
Ed
yankneck696
01-18-2011, 07:00 AM #1Does anyone have knowledge of an OM61X or OM60X being able to run in reverse rotation for a marine application? I would really like to replace the 318 with a Merc. Problrm is that the prop, strut, tunnel & rudder are designed for RR & the trans to reverse the rotation & stay at 1:1 costs more than a 7.5MM IP.
Application 1975 Penn Yan Avenger flybridge.
Thankyou,
Ed
01-18-2011, 07:43 PM
#3
yankneck696
01-18-2011, 07:43 PM #3Bump for anyone else? Hey Forced, I like the new graphics... How do ya do that?
01-18-2011, 08:03 PM
#4
1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
01-18-2011, 08:03 PM #4Handcuffs are not bracelets my friend
1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
01-18-2011, 09:20 PM
#5
The only diesels I've seen run reverse rotation are all gear driven.
-Jesse
80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon
10 mistsubishi fuso service truck.
No you cannot the timing chain won't take it. The tensioner would be one the pull side of the chain and it will wear very fast and cause the chain to skip either the injection pump or cam.
The only diesels I've seen run reverse rotation are all gear driven.
-Jesse
80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon
10 mistsubishi fuso service truck.
01-19-2011, 06:21 AM
#6
(01-18-2011, 09:20 PM)dieselboy No you cannot the timing chain won't take it. The tensioner would be one the pull side of the chain and it will wear very fast and cause the chain to skip either the injection pump or cam.
The only diesels I've seen run reverse rotation are all gear driven.
Well, I guess that's a good enough reason. I usually work on marine diesels & they are primarily gear driven. Thanks, Jessie.
yankneck696
01-19-2011, 06:21 AM #6(01-18-2011, 09:20 PM)dieselboy No you cannot the timing chain won't take it. The tensioner would be one the pull side of the chain and it will wear very fast and cause the chain to skip either the injection pump or cam.
The only diesels I've seen run reverse rotation are all gear driven.
Well, I guess that's a good enough reason. I usually work on marine diesels & they are primarily gear driven. Thanks, Jessie.
01-19-2011, 01:11 PM
#7
Now I'm not saying the OM617a is a good candidate to do that with only because I have no idea how well it would work. Just a thought to think about.
Back in the day, ChrisCraft turned the engines around and used the front of the crank as the PTO, the flywheel was up front.
Now I'm not saying the OM617a is a good candidate to do that with only because I have no idea how well it would work. Just a thought to think about.
01-19-2011, 05:08 PM
#8
(01-19-2011, 01:11 PM)OM616 Back in the day, ChrisCraft turned the engines around and used the front of the crank as the PTO, the flywheel was up front.
Now I'm not saying the OM617a is a good candidate to do that with only because I have no idea how well it would work. Just a thought to think about.
here's a real response. I'll look into that.
yankneck696
01-19-2011, 05:08 PM #8(01-19-2011, 01:11 PM)OM616 Back in the day, ChrisCraft turned the engines around and used the front of the crank as the PTO, the flywheel was up front.
Now I'm not saying the OM617a is a good candidate to do that with only because I have no idea how well it would work. Just a thought to think about.
here's a real response. I'll look into that.
01-19-2011, 07:30 PM
#9
It might work for awhile but I wouldn't trust it in a boat.
What transmissionS are you running?
-Jesse
80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon
10 mistsubishi fuso service truck.
I've seen pto drives off the front of the crank but never a transmission. There's a reason the back of the cranks are so stout. It would put alot of load on the small part of the crankshaft.
It might work for awhile but I wouldn't trust it in a boat.
What transmissionS are you running?
-Jesse
80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon
10 mistsubishi fuso service truck.
01-20-2011, 06:26 AM
#10
(01-19-2011, 07:30 PM)dieselboy I've seen pto drives off the front of the crank but never a transmission. There's a reason the back of the cranks are so stout. It would put alot of load on the small part of the crankshaft.
It might work for awhile but I wouldn't trust it in a boat.
What transmissionS are you running?
It's a single engine with a 1:1 velvet drive.
yankneck696
01-20-2011, 06:26 AM #10(01-19-2011, 07:30 PM)dieselboy I've seen pto drives off the front of the crank but never a transmission. There's a reason the back of the cranks are so stout. It would put alot of load on the small part of the crankshaft.
It might work for awhile but I wouldn't trust it in a boat.
What transmissionS are you running?
It's a single engine with a 1:1 velvet drive.
01-20-2011, 03:01 PM
#12
-Jesse
80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon
10 mistsubishi fuso service truck.
Oh single? Reverse rotation prop then. On a velvet drive just turn the pump around.
-Jesse
80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon
10 mistsubishi fuso service truck.
01-20-2011, 03:38 PM
#13
I thought changing the pump rotation is for a different engine rotation.the VD still puts out the same rotation in & out while in forward. Please correct me if I'm wrong.
yankneck696
01-20-2011, 03:38 PM #13Firstly, the tunnel drive becomes really lossy if ya use the wrong rotation unless you change strut, rudder & engine alignment
I thought changing the pump rotation is for a different engine rotation.the VD still puts out the same rotation in & out while in forward. Please correct me if I'm wrong.
01-20-2011, 04:30 PM
#14
What kind of boat?
I thought with the 1:1 vd when you turn the pump cover over it changes the rotation direction of the input so Fwd would still be Fwd. So you could still keep your prop rotation the same.
We junked our vd infavor of a zf so I dunno anything other than that.
This post was last modified: 01-20-2011, 04:34 PM by dieselboy.
-Jesse
80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon
10 mistsubishi fuso service truck.
Oh well then your sol if your concerned about that.
What kind of boat?
I thought with the 1:1 vd when you turn the pump cover over it changes the rotation direction of the input so Fwd would still be Fwd. So you could still keep your prop rotation the same.
We junked our vd infavor of a zf so I dunno anything other than that.
-Jesse
80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon
10 mistsubishi fuso service truck.
01-20-2011, 05:33 PM
#16
-Jesse
80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon
10 mistsubishi fuso service truck.
I don't know if you'd notice the reverse rotation in that big of a boat and that little power.
-Jesse
80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon
10 mistsubishi fuso service truck.
01-20-2011, 09:35 PM
#18
-Jesse
80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon
10 mistsubishi fuso service truck.
Cause they cannot hold 100% cycle duty in reverse cause it runs through a planetary in reverse.
-Jesse
80 300sd hy35, front mount intercooler, w115 intake, rack limiter removed, Alda removed, full load turned up, boost, ebp, trans, pyro, egr delete, 3.5" exhaust, e-fan, 16x8 rims with, 245/50 tires, lowered, bilstien 5100's, 12" front brakes, 2.65:1 diff.
97 f250 psd 4x4, crawler
70 f250 390
83 Volvo 242, lots of mods
66 Volvo amazon
10 mistsubishi fuso service truck.
Users browsing this thread:
10 Guest(s)
10 Guest(s)
Users browsing this thread:
10 Guest(s)
10 Guest(s)