STD Other Projects TheDon Bought a 240D

TheDon Bought a 240D

TheDon Bought a 240D

 
  • 0 Vote(s) - 0 Average
 
TheDon
606 Power!!

247
06-18-2011, 10:39 AM #1
[Image: 263886_10150195078816534_589171533_74019...7346_n.jpg]

1982 240D 4 speed with 309k miles and a trunk triangle to boot!

No rust, just some small spots here and there. Engine runs well(I think it does), transmission shifts decently(I've never driven stick before), AC works, sunroof works, all 4 windows go down via the hand crank.

I think it has a vacuum leak somewhere and the ignition key only works in the ignition.Front right door will not catch all the way. Interior needs to be cleaned up and drivers seat replaced. I also suspect the fuel tank sender may be gunked up since I drove it home almost 180 miles and the needle did not move.

I have never driven a 240D and boy is everyone right. They are slow but the 4 speed helps.

This is the replacement for my step dad's Aveo that bit the dust. I just need to clean it up, replace engine mounts, make sure the suspension is good, engine is strong, etc.

But, I do like it. I also named it Pancakes.
TheDon
06-18-2011, 10:39 AM #1

[Image: 263886_10150195078816534_589171533_74019...7346_n.jpg]

1982 240D 4 speed with 309k miles and a trunk triangle to boot!

No rust, just some small spots here and there. Engine runs well(I think it does), transmission shifts decently(I've never driven stick before), AC works, sunroof works, all 4 windows go down via the hand crank.

I think it has a vacuum leak somewhere and the ignition key only works in the ignition.Front right door will not catch all the way. Interior needs to be cleaned up and drivers seat replaced. I also suspect the fuel tank sender may be gunked up since I drove it home almost 180 miles and the needle did not move.

I have never driven a 240D and boy is everyone right. They are slow but the 4 speed helps.

This is the replacement for my step dad's Aveo that bit the dust. I just need to clean it up, replace engine mounts, make sure the suspension is good, engine is strong, etc.

But, I do like it. I also named it Pancakes.

TheDon
606 Power!!

247
06-18-2011, 11:51 AM #2
[Image: IMG_4808-1.jpg]

[Image: IMG_4799.jpg]

[Image: IMG_4798.jpg]

[Image: IMG_4807.jpg]

[Image: IMG_4806.jpg]

[Image: IMG_4805.jpg]

[Image: IMG_4804.jpg]

[Image: IMG_4803.jpg]

[Image: IMG_4802.jpg]

[Image: IMG_4801.jpg]

[Image: IMG_4800.jpg]

[Image: IMG_4799.jpg]

[Image: IMG_4798.jpg]
TheDon
06-18-2011, 11:51 AM #2

[Image: IMG_4808-1.jpg]

[Image: IMG_4799.jpg]

[Image: IMG_4798.jpg]

[Image: IMG_4807.jpg]

[Image: IMG_4806.jpg]

[Image: IMG_4805.jpg]

[Image: IMG_4804.jpg]

[Image: IMG_4803.jpg]

[Image: IMG_4802.jpg]

[Image: IMG_4801.jpg]

[Image: IMG_4800.jpg]

[Image: IMG_4799.jpg]

[Image: IMG_4798.jpg]

TheDon
606 Power!!

247
06-26-2011, 06:07 PM #3
[Image: 268517_10150203215746534_589171533_74628...7628_n.jpg]

Temporary, Gangster solution until I can get money to rebuild the suspension and get new tires for the original wheels/hub caps.

[Image: 354f5902fa934b09a81e98f0f643fc5d_7.jpg]
TheDon
06-26-2011, 06:07 PM #3

[Image: 268517_10150203215746534_589171533_74628...7628_n.jpg]

Temporary, Gangster solution until I can get money to rebuild the suspension and get new tires for the original wheels/hub caps.

[Image: 354f5902fa934b09a81e98f0f643fc5d_7.jpg]

Captain America
Boostin' & Roostin'

2,221
06-27-2011, 12:14 PM #4
Please sell the gangster wheels to me!


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
06-27-2011, 12:14 PM #4

Please sell the gangster wheels to me!



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

TheDon
606 Power!!

247
07-22-2011, 10:37 PM #5
I have them on hold for someone else until I get the front end rebuilt and the original wheels back on.
TheDon
07-22-2011, 10:37 PM #5

I have them on hold for someone else until I get the front end rebuilt and the original wheels back on.

TheDon
606 Power!!

247
08-17-2011, 09:49 AM #6
[Image: 223731_10150251640061534_589171533_78580...4788_n.jpg]

slowly but surely I am rebuilding this car.

Swapped in a lower mile transmission due to 1st gear not working properly. Which turned out to be a loose shifter arm on the transmission. Oh well. Drained the gear oil out of the new transmission and filled with Pennzoil synchromesh. Shifts like butter. I still need to rebuild the shifter mechanism it self. But my mechanic said the synchros feel a lot better in the new transmission that the old one. Which was filled with ATF.

I have a new water pump to install, then get an alignment, do rear subframe bushings, front pads and rotors. and a lot more as usual!
TheDon
08-17-2011, 09:49 AM #6

[Image: 223731_10150251640061534_589171533_78580...4788_n.jpg]

slowly but surely I am rebuilding this car.

Swapped in a lower mile transmission due to 1st gear not working properly. Which turned out to be a loose shifter arm on the transmission. Oh well. Drained the gear oil out of the new transmission and filled with Pennzoil synchromesh. Shifts like butter. I still need to rebuild the shifter mechanism it self. But my mechanic said the synchros feel a lot better in the new transmission that the old one. Which was filled with ATF.

I have a new water pump to install, then get an alignment, do rear subframe bushings, front pads and rotors. and a lot more as usual!

willbhere4u
Six in a row make her go!

2,507
08-17-2011, 11:26 AM #7
That spare in your trunk is very rare alloy wheel for hubcaps!

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
08-17-2011, 11:26 AM #7

That spare in your trunk is very rare alloy wheel for hubcaps!


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

DanielK
Big Plans, No Clue

98
08-21-2011, 04:32 PM #8
Will, that is a dashed stripe. It is a steelie.

[Image: FalkonSig.png]
DanielK
08-21-2011, 04:32 PM #8

Will, that is a dashed stripe. It is a steelie.


[Image: FalkonSig.png]

willbhere4u
Six in a row make her go!

2,507
08-21-2011, 05:22 PM #9
That's how all of the alloys on my car are the steel's are usually all black

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
08-21-2011, 05:22 PM #9

That's how all of the alloys on my car are the steel's are usually all black


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

mike-81-240d
more like mike-84-300d now

427
08-22-2011, 05:03 PM #10
(08-21-2011, 04:32 PM)DanielK Will, that is a dashed stripe. It is a steelie.

Dashed line means 5.5 inch width. Solid line means 6 inch width.

1981 Mercedes 300TD Lowered 4 speed manual Holset HX30 
mike-81-240d
08-22-2011, 05:03 PM #10

(08-21-2011, 04:32 PM)DanielK Will, that is a dashed stripe. It is a steelie.

Dashed line means 5.5 inch width. Solid line means 6 inch width.


1981 Mercedes 300TD Lowered 4 speed manual Holset HX30 

DanielK
Big Plans, No Clue

98
08-23-2011, 04:23 PM #11
Alloys never came in 5.5, only 6".

[Image: FalkonSig.png]
DanielK
08-23-2011, 04:23 PM #11

Alloys never came in 5.5, only 6".


[Image: FalkonSig.png]

willbhere4u
Six in a row make her go!

2,507
08-23-2011, 08:22 PM #12
The alloy's on my 1980 240d are 5 1/2 J x 14 h2 (5.5x14) part # 123 400 13 02 and they are defiantly alloys!

If it was a steel it would have rust round the outer edge!
This post was last modified: 08-23-2011, 08:28 PM by willbhere4u.
Attached Files
Image(s)
           

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
08-23-2011, 08:22 PM #12

The alloy's on my 1980 240d are 5 1/2 J x 14 h2 (5.5x14) part # 123 400 13 02 and they are defiantly alloys!

If it was a steel it would have rust round the outer edge!

Attached Files
Image(s)
           

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

Captain America
Boostin' & Roostin'

2,221
08-23-2011, 11:30 PM #13
This has become a wheel thread lol


1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

Captain America
08-23-2011, 11:30 PM #13

This has become a wheel thread lol



1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag

AX15 Jeep Trans swap in progress....

DanielK
Big Plans, No Clue

98
08-24-2011, 01:14 PM #14
Interesting, I was misinformed then. TheDon, beautiful car! lol

[Image: FalkonSig.png]
DanielK
08-24-2011, 01:14 PM #14

Interesting, I was misinformed then. TheDon, beautiful car! lol


[Image: FalkonSig.png]

mike-81-240d
more like mike-84-300d now

427
08-24-2011, 03:04 PM #15
Mine are also 5.5 alloy not steel. Came on my old 1981 240D. Kept them when I sold it.

1981 Mercedes 300TD Lowered 4 speed manual Holset HX30 
mike-81-240d
08-24-2011, 03:04 PM #15

Mine are also 5.5 alloy not steel. Came on my old 1981 240D. Kept them when I sold it.


1981 Mercedes 300TD Lowered 4 speed manual Holset HX30 

willbhere4u
Six in a row make her go!

2,507
08-25-2011, 09:59 AM #16
looking at his car makes me want to finish mine!
I cant wait to drive it again!

1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running
willbhere4u
08-25-2011, 09:59 AM #16

looking at his car makes me want to finish mine!
I cant wait to drive it again!


1987 300SDL 6spd manual om606.962 swap project
1985 300td euro 5spd wagon running

 
  • 0 Vote(s) - 0 Average
Users browsing this thread:
 7 Guest(s)
Users browsing this thread:
 7 Guest(s)