Changed the subframe bushings but..
Changed the subframe bushings but..
03-18-2012, 08:40 PM
#1
Do I NEED to make sure they are properly in place or will they just sink in?
btw, the rear end is very tight now
Purplecomputer
03-18-2012, 08:40 PM #1but.. they wont go all the way in. I tightened the big bolt which kinda looks like an AK47 bullet all the way in and its tight as can be but the bushings stick out a little.
Do I NEED to make sure they are properly in place or will they just sink in?
btw, the rear end is very tight now
Purplecomputer
03-19-2012, 04:47 PM #2no one has any input? Maybe ill post some pictures later tonight
03-19-2012, 09:12 PM
#3
'84 300 SD w126 Race Car
'86 190E 2.3 w201 Daily Driver
'85 500 SEL w126 Scraped
'92 1.6 Geo Storm Totaled by a Uninsured Driver
serverman777
03-19-2012, 09:12 PM #3" the rear end is very tight now" haha I like the sound of that.
'84 300 SD w126 Race Car
'86 190E 2.3 w201 Daily Driver
'85 500 SEL w126 Scraped
'92 1.6 Geo Storm Totaled by a Uninsured Driver
03-19-2012, 11:55 PM
#4
(03-19-2012, 09:12 PM)serverman777 " the rear end is very tight now" haha I like the sound of that.
lol
-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
03-19-2012, 11:55 PM #4(03-19-2012, 09:12 PM)serverman777 " the rear end is very tight now" haha I like the sound of that.
lol
-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
03-20-2012, 05:57 AM
#5
Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
Simpler=Better
03-20-2012, 05:57 AM #5Were the new bushings significantly smaller than the old ones? Did you oil the threads or anything? When I pulled mine it al went back together no problem
Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
03-20-2012, 08:24 AM
#6
(03-20-2012, 05:57 AM)Simpler=Better Were the new bushings significantly smaller than the old ones? Did you oil the threads or anything? When I pulled mine it al went back together no problem
The new bushings are a very tight squeze. Almost to the point were i would need to have some sort of tool to press them in i cant push them in with my hands. Also i never removed the subframe to do this job.
Purplecomputer
03-20-2012, 08:24 AM #6(03-20-2012, 05:57 AM)Simpler=Better Were the new bushings significantly smaller than the old ones? Did you oil the threads or anything? When I pulled mine it al went back together no problem
The new bushings are a very tight squeze. Almost to the point were i would need to have some sort of tool to press them in i cant push them in with my hands. Also i never removed the subframe to do this job.
Users browsing this thread:
4 Guest(s)
4 Guest(s)
Users browsing this thread:
4 Guest(s)
4 Guest(s)