Re-weld BMW 6spd
Re-weld BMW 6spd
This is made for a single mass flywheel.
The gearbox is a smaller cousin to the gs6-53dz that can withstand a nuclear war. But this is a tough bastard also... Only rated for 370Nm of torque by ZF, but the older 5spd where only rated for 320Nm and they have been proved to cope with KNm here in Sweden.
This smaller gearbox is easier to fit in older cars with narrow tunnels.
![[Image: 20140514_121542.jpg]](http://www.f-tune.se/wp-content/uploads/2014/05/20140514_121542.jpg)
![[Image: 20140514_121616.jpg]](http://www.f-tune.se/wp-content/uploads/2014/05/20140514_121616.jpg)
F-tune Performance
![[Image: V-band_om606.jpg]](http://www.f-tune.se/wp-content/uploads/2015/01/V-band_om606.jpg)
![[Image: GTX3582R.jpg]](http://www.f-tune.se/wp-content/uploads/2015/01/GTX3582R.jpg)
![[Image: gs6-53dz_gearbox.jpg]](http://www.f-tune.se/wp-content/uploads/2015/01/gs6-53dz_gearbox.jpg)
I can help you out with all your manual transmission, clutch, flywheel, intake and exhaust manifold issues.
Just posting two pictures for you of a rewelded gs6-37dz gearbox (don't mind the writing on the gearbox).
This is made for a single mass flywheel.
The gearbox is a smaller cousin to the gs6-53dz that can withstand a nuclear war. But this is a tough bastard also... Only rated for 370Nm of torque by ZF, but the older 5spd where only rated for 320Nm and they have been proved to cope with KNm here in Sweden.
This smaller gearbox is easier to fit in older cars with narrow tunnels.
F-tune Performance
I can help you out with all your manual transmission, clutch, flywheel, intake and exhaust manifold issues.
(05-16-2014, 12:56 PM)raysorenson How to you clean dirty cast aluminum before welding?
You need to heat the oil out of it. Be careful not to warp it or get so hot that it weakens things.
Also, cleaning with alyminym prep fluid and a brand new brush helps too.
Always pre-heat before welding too.
Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
Simpler=Better
05-16-2014, 01:30 PM #4(05-16-2014, 12:56 PM)raysorenson How to you clean dirty cast aluminum before welding?
You need to heat the oil out of it. Be careful not to warp it or get so hot that it weakens things.
Also, cleaning with alyminym prep fluid and a brand new brush helps too.
Always pre-heat before welding too.
Newbie-read this: Cheap Tricks
617.952-220k-Getting built up
larsalan I guess I need to look at this stupid ass drip shit. What you have to like mess with those elements on the pump? What a fucking hassle. then use some wire to hold the throttle open or some shit?
F-tune Performance
I can help you out with all your manual transmission, clutch, flywheel, intake and exhaust manifold issues.
Smaller stuff we usually put in the blaster cabinet. But to be honest, the casting in this one was super clean so it was very easy to weld, and some cleaning with the angle grinder usually does the trick. We do a lot of oil pans and such and for sure it can be a pain in the a**
F-tune Performance
I can help you out with all your manual transmission, clutch, flywheel, intake and exhaust manifold issues.
2 Guest(s)
2 Guest(s)