Captain's '82 300D Purists Must Die Prius Repellent
Captain's '82 300D Purists Must Die Prius Repellent
03-26-2015, 12:48 PM
#401
raysorenson
03-26-2015, 12:48 PM #401If you're crawling, why go to a manual trans? Just get a converter modded and you're good.
04-05-2015, 11:35 PM
#402
(03-25-2015, 06:53 AM)DanielK There's almost always a lower gear. Rev it out. lol.
I really want to get one of those 617/jeep trans adapters and put the trans/transfer case and axles from a jeep under a W123 wagon. Ultimate SUV.
Forced to climb most hills in 2nd because you can rev 1st!
That would be legit! I considered doing that!
This post was last modified: 04-06-2015, 12:12 AM by Captain America.
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-05-2015, 11:35 PM #402(03-25-2015, 06:53 AM)DanielK There's almost always a lower gear. Rev it out. lol.
I really want to get one of those 617/jeep trans adapters and put the trans/transfer case and axles from a jeep under a W123 wagon. Ultimate SUV.
Forced to climb most hills in 2nd because you can rev 1st!
That would be legit! I considered doing that!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
04-05-2015, 11:40 PM
#403
(03-26-2015, 12:48 PM)raysorenson If you're crawling, why go to a manual trans? Just get a converter modded and you're good.
Modded in what way? I already have the high stall (2600rpm) out of an '85 and its perfect for street driving, I can make full boost whenever and where ever I want, but in the dirt under a high load situation, RPM stays up at stall speed but the converter isn't spinning the tires fast enough. I usually hit hills in 2nd gear as 1st cannot be revved past 4000 without automatic change. So that's dumb and the fact that my trans couldn't hold the power make its that much more worthless.
Monitor my wheel speed in this video and see how rpm never changes...
This post was last modified: 04-05-2015, 11:53 PM by Captain America.
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-05-2015, 11:40 PM #403(03-26-2015, 12:48 PM)raysorenson If you're crawling, why go to a manual trans? Just get a converter modded and you're good.
Modded in what way? I already have the high stall (2600rpm) out of an '85 and its perfect for street driving, I can make full boost whenever and where ever I want, but in the dirt under a high load situation, RPM stays up at stall speed but the converter isn't spinning the tires fast enough. I usually hit hills in 2nd gear as 1st cannot be revved past 4000 without automatic change. So that's dumb and the fact that my trans couldn't hold the power make its that much more worthless.
Monitor my wheel speed in this video and see how rpm never changes...
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
04-06-2015, 12:02 AM
#404
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-06-2015, 12:02 AM #404Last, I think, of the videos
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
04-10-2015, 01:04 AM
#405
![[Image: IMG_20131116_212926.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/IMG_20131116_212926.jpg)
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-10-2015, 01:04 AM #405There was that one time a little over a year ago that the B2 piston broke and I fixed that pile of shit
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
04-10-2015, 01:07 AM
#406
![[Image: received_m_mid_1392618880543_d2207594c6f9228783_1.jpeg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/received_m_mid_1392618880543_d2207594c6f9228783_1.jpeg)
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-10-2015, 01:07 AM #406Couple Years ago at King Of The Hammers
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
04-10-2015, 01:10 AM
#407
![[Image: img_20141227_112918329_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20141227_112918329_hdr.jpg)
![[Image: img_20141227_151144835_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20141227_151144835_hdr.jpg)
![[Image: img_20141227_140502595_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20141227_140502595_hdr.jpg)
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-10-2015, 01:10 AM #407Trip up to my local highest point 6000 ft.
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
04-10-2015, 01:11 AM
#408
![[Image: img_20150103_125426403_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20150103_125426403_hdr.jpg)
![[Image: img_20150103_125155468.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20150103_125155468.jpg)
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-10-2015, 01:11 AM #408Went up this hill bro runners cant even make!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
04-10-2015, 01:16 AM
#409
![[Image: 10899517_603781019754678_1733108817_n.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/10899517_603781019754678_1733108817_n.jpg)
![[Image: img_20150118_124932893_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20150118_124932893_hdr.jpg)
![[Image: img_20150118_171422440_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20150118_171422440_hdr.jpg)
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-10-2015, 01:16 AM #409Then I locked the diff because I got impatient!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
04-10-2015, 01:18 AM
#410
![[Image: img_20150127_125356958_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20150127_125356958_hdr.jpg)
![[Image: img_20150130_192259237_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20150130_192259237_hdr.jpg)
![[Image: img_20150130_205122208_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20150130_205122208_hdr.jpg)
![[Image: img_20150131_100854976_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20150131_100854976_hdr.jpg)
![[Image: img_20150131_100939282_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20150131_100939282_hdr.jpg)
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-10-2015, 01:18 AM #410Got fresh meat for the hammers Maxxis BigHorn Mud Terrain 27x8.5/R14
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
04-10-2015, 01:21 AM
#411
![[Image: img_20150204_173144505.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20150204_173144505.jpg)
![[Image: img_20150205_081319756_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20150205_081319756_hdr.jpg)
![[Image: img_20150205_081332554.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20150205_081332554.jpg)
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-10-2015, 01:21 AM #411My Tie Rods were HAMMERED so I made some quality ones haha!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
04-10-2015, 01:23 AM
#412
![[Image: img_20150202_074646834.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20150202_074646834.jpg)
![[Image: img_20150203_242300069_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20150203_242300069_hdr.jpg)
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-10-2015, 01:23 AM #412Trashed the Flex disks and center support. that was only 245$$$$$$$$$$$$ fuck
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
04-10-2015, 01:27 AM
#413
At the hill called Jackhammer
![[Image: img_20150205_162451951_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20150205_162451951_hdr.jpg)
At Camp
![[Image: img_20150206_111602401_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20150206_111602401_hdr.jpg)
![[Image: img_20150206_111621593_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20150206_111621593_hdr.jpg)
At Top of Chocolate Thunder
![[Image: img_20150207_015026861_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20150207_015026861_hdr.jpg)
Made it further up the sand dune than a 4 wheel drive 4runner. FUCK YOU JAPAN!
![[Image: 10986355_865290523493610_1901246527_n.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/10986355_865290523493610_1901246527_n.jpg)
On the way home
![[Image: img_20150207_163336395_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20150207_163336395_hdr.jpg)
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-10-2015, 01:27 AM #413KING OF THE HAMMERS 2015!!!
At the hill called Jackhammer
At Camp
At Top of Chocolate Thunder
Made it further up the sand dune than a 4 wheel drive 4runner. FUCK YOU JAPAN!
On the way home
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
04-10-2015, 01:38 AM
#414
![[Image: img_20150209_220936748_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/img_20150209_220936748_hdr.jpg)
Bam AX15 for $450 and 50" Rigid radius light bar fo FREE
![[Image: rsz_img_20150221_171242927.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/rsz_img_20150221_171242927.jpg)
Got my adapter plate from Mercedes Diesel 4x4 . com
![[Image: rsz_img_20150401_171859595_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/rsz_img_20150401_171859595_hdr.jpg)
Will need to relocate shifter something like this as the shifter in the trans will be under the dash or 10" forward of the shifter in the car
![[Image: rsz_shifter_relocate.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/rsz_shifter_relocate.jpg)
Going to get flywheel and clutch next week along with peddles and rip that shit ass auto out next week!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-10-2015, 01:38 AM #414Trans took a shit THE DAY AFTER king of the hammers So it sits at my work waiting for the AX15!
Bam AX15 for $450 and 50" Rigid radius light bar fo FREE
Got my adapter plate from Mercedes Diesel 4x4 . com
Will need to relocate shifter something like this as the shifter in the trans will be under the dash or 10" forward of the shifter in the car
Going to get flywheel and clutch next week along with peddles and rip that shit ass auto out next week!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
![[Image: FalkonSig.png]](http://i160.photobucket.com/albums/t162/DanielWGK2/designs/FalkonSig.png)
04-10-2015, 11:11 AM
#416
(04-10-2015, 05:02 AM)DanielK Those tires are MEAT.
How'd you score the freebies?
I absolutely love this car.
Thanks Daniel! She's coming along man, been a long road but almost done! I work for Jeremy McGrath so I can basically get anything I want from our sponsors like tires and the lightbar
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-10-2015, 11:11 AM #416(04-10-2015, 05:02 AM)DanielK Those tires are MEAT.
How'd you score the freebies?
I absolutely love this car.
Thanks Daniel! She's coming along man, been a long road but almost done! I work for Jeremy McGrath so I can basically get anything I want from our sponsors like tires and the lightbar
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
04-10-2015, 11:24 AM
#417
What's your plan for the flywheel/clutch/pressure plate? The 240 flywheel with the stock 215mm clutch will not hold much.
1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
led-panzer
04-10-2015, 11:24 AM #417Awesome. I love it.
What's your plan for the flywheel/clutch/pressure plate? The 240 flywheel with the stock 215mm clutch will not hold much.
1984 300D 4-speed ~200,000 miles
7.5mm M-pump, GT3582 turbo, F-Tune Performance intake/exhaust manifolds, A/A intercooler, 315 nozzles, Enlarged prechambers, Bosch 044 feed pump, Custom lightweight flywheel with 240mm clutch, Lowered, 17" AMG rims - 300 hp OM617 project
1985 300D 280,000 miles RIP
2001 F350 7.3 DP tuner, 4"exhaust, S&B intake
04-10-2015, 11:33 AM
#418
(04-10-2015, 11:24 AM)led-panzer Awesome. I love it.
What's your plan for the flywheel/clutch/pressure plate? The 240 flywheel with the stock 215mm clutch will not hold much.
Thanks man! I will be using all jeep parts including flywheel and clutch components. Pretty cool there is a lot to choose from. I'm just going with new stock stuff since the jeep I6 makes 190hp and 224tq so it should hold the 617 power no problem I think. But hey who knows we'll see!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-10-2015, 11:33 AM #418(04-10-2015, 11:24 AM)led-panzer Awesome. I love it.
What's your plan for the flywheel/clutch/pressure plate? The 240 flywheel with the stock 215mm clutch will not hold much.
Thanks man! I will be using all jeep parts including flywheel and clutch components. Pretty cool there is a lot to choose from. I'm just going with new stock stuff since the jeep I6 makes 190hp and 224tq so it should hold the 617 power no problem I think. But hey who knows we'll see!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
04-11-2015, 01:40 AM
#420
(04-10-2015, 06:59 PM)DanielK Can you score some D44's? I found a W123 300TD with no glass for, get this, $50. Jussayin.
D44?
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-11-2015, 01:40 AM #420(04-10-2015, 06:59 PM)DanielK Can you score some D44's? I found a W123 300TD with no glass for, get this, $50. Jussayin.
D44?
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
04-17-2015, 01:33 AM
#422
(04-11-2015, 02:15 AM)DanielK Dana 44. The stock axles that come on Jeep Wranglers
Oh ya, I have one Rubicon 44 thats going in my XJ all I need is a front. Mercedes is not getting SAS'd lol.
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-17-2015, 01:33 AM #422(04-11-2015, 02:15 AM)DanielK Dana 44. The stock axles that come on Jeep Wranglers
Oh ya, I have one Rubicon 44 thats going in my XJ all I need is a front. Mercedes is not getting SAS'd lol.
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
04-17-2015, 01:34 AM
#423
![[Image: rsz_img_20150416_210609.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/rsz_img_20150416_210609.jpg)
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-17-2015, 01:34 AM #423BAM! Man peddles courtesy of DELIVERY VALVE!!!! Thank you sooooo much!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
04-17-2015, 02:06 AM
#424
P.S. those calipers aren't for the 300D also, are they?
______________________________
'85 300D ~ 381,XXX miles, HD Bilstein shocks, 27.50x8.50x14R General Grabber AT2 tires, 4 E-Code headlight upgrade with 90w/130w bulbs, boost turned up, new timing chain, and injectors. Brought back from the dead and the hell of WVO! SOLD
'85 CJ7 ~ OM617 swap, Taurus electric fan, T5 trans, Dana 300, 4.88 R&P, Mile Marker locking hubs, ALDA removed, MKII hybrid boost controller, Greazzer's upgraded overflow valve, AMC 20 rear disk brake conversion, Aussie locked with 33's and 5" Rough Country lift.
Nice! What else are you lacking to get the swap started?
P.S. those calipers aren't for the 300D also, are they?
______________________________
'85 300D ~ 381,XXX miles, HD Bilstein shocks, 27.50x8.50x14R General Grabber AT2 tires, 4 E-Code headlight upgrade with 90w/130w bulbs, boost turned up, new timing chain, and injectors. Brought back from the dead and the hell of WVO! SOLD
'85 CJ7 ~ OM617 swap, Taurus electric fan, T5 trans, Dana 300, 4.88 R&P, Mile Marker locking hubs, ALDA removed, MKII hybrid boost controller, Greazzer's upgraded overflow valve, AMC 20 rear disk brake conversion, Aussie locked with 33's and 5" Rough Country lift.
04-17-2015, 02:22 AM
#425
(04-17-2015, 02:06 AM)turbojeep Nice! What else are you lacking to get the swap started?
P.S. those calipers aren't for the 300D also, are they?
Just down to small parts now! Need:
Clutch master and reservoir
Jeep 4.0 Flywheel
Jeep 4.0 clutch assembly with slave and all
Jeep 4.0 starter
But I can get the swap started without that stuff. The engine oil pan has to be clearances for the Jeep starter and I will need to see how the Ax15 fits in the trans tunnel. Make a hole in the tunnel for the shifter. Start to fab trans cross member. Also modify driveshaft with 1310 yolks. Install peddles. Make clutch hydraulic line. Make shifter relocation.
---P.S.... Haha no those are Brembo Monoblock radial mount race calipers for Jeremy McGraths short course truck. They're about $2000 a piece, lol and I have them stacked like they're nothing ha
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-17-2015, 02:22 AM #425(04-17-2015, 02:06 AM)turbojeep Nice! What else are you lacking to get the swap started?
P.S. those calipers aren't for the 300D also, are they?
Just down to small parts now! Need:
Clutch master and reservoir
Jeep 4.0 Flywheel
Jeep 4.0 clutch assembly with slave and all
Jeep 4.0 starter
But I can get the swap started without that stuff. The engine oil pan has to be clearances for the Jeep starter and I will need to see how the Ax15 fits in the trans tunnel. Make a hole in the tunnel for the shifter. Start to fab trans cross member. Also modify driveshaft with 1310 yolks. Install peddles. Make clutch hydraulic line. Make shifter relocation.
---P.S.... Haha no those are Brembo Monoblock radial mount race calipers for Jeremy McGraths short course truck. They're about $2000 a piece, lol and I have them stacked like they're nothing ha
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
04-21-2015, 01:21 AM
#427
(04-17-2015, 10:09 PM)wolverine Badass, cant wait to see the manual swap results :thumbsup:
Going the one piece driveshaft route? Or just shortening the front shaft and leaving the center bearing? With my T5 swap, the front shaft would have been about 8" long.
Yes more than likely I'll one piece the driveshaft and also put a 1310 Yolk on the diff. I got a 2wd Cherokee XJ driveshaft at the yard for $40 so going to start there. We're racing in Phoenix this weekend so I should be able to start the swap next weekend.
This post was last modified: 04-21-2015, 01:22 AM by Captain America.
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-21-2015, 01:21 AM #427(04-17-2015, 10:09 PM)wolverine Badass, cant wait to see the manual swap results :thumbsup:
Going the one piece driveshaft route? Or just shortening the front shaft and leaving the center bearing? With my T5 swap, the front shaft would have been about 8" long.
Yes more than likely I'll one piece the driveshaft and also put a 1310 Yolk on the diff. I got a 2wd Cherokee XJ driveshaft at the yard for $40 so going to start there. We're racing in Phoenix this weekend so I should be able to start the swap next weekend.
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
04-21-2015, 03:28 PM
#428
-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
sassparilla_kid
04-21-2015, 03:28 PM #428Can you just get a 1310 yoke to diff adapter plate thing made up? I've been thinking it might be good to look in to, one for each end, and go one piece driveshaft. Would also be nice to have greasable u-joints haha
-1982 300D Turbo, 280k miles, ALDA apparently maxxed, fram 8038, 12 lbs boost, non-egr manifolds, W/M injection, 4 brake light mod, Gen II w126 front rotors/calipers, 4-speed swap
In the works: A/W IC, adjust pump, turbo rebuild (w/60 trim comp wheel)
-1980 300SD, 110k, project car. Goal is to get it lookin' like it did on the showroom floor (body and interior wise, not necessarily under the hood )
-1974 240D, FRESH PAINT!!!!!!
04-22-2015, 07:27 PM
#429
raysorenson
04-22-2015, 07:27 PM #429If you're going 1 piece, you need a sliding YOKE on the output shaft, lubed with egg YOLK. As I understand, a sliding yoke in the middle of the shaft, not the output shaft, will affect radial stability on a shaft long enough for the typical sedan. They're fine on jeeps and other 4x4's that take stubby drive shafts but not for us. A sliding yoke mounted in the shaft needs a larger diameter the longer the shaft gets. There's not enough room in the tunnel for the shifter and a 3" diameter shaft. Does that make any sense?
04-23-2015, 01:10 AM
#431
(04-22-2015, 07:27 PM)raysorenson If you're going 1 piece, you need a sliding YOKE on the output shaft, lubed with egg YOLK. As I understand, a sliding yoke in the middle of the shaft, not the output shaft, will affect radial stability on a shaft long enough for the typical sedan. They're fine on jeeps and other 4x4's that take stubby drive shafts but not for us. A sliding yoke mounted in the shaft needs a larger diameter the longer the shaft gets. There's not enough room in the tunnel for the shifter and a 3" diameter shaft. Does that make any sense?
Ah well congrats on correcting my spelling. The shaft will infact, be a larger diameter than stock w123 and what shifter will I need to worry about genius?
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
04-23-2015, 01:10 AM #431(04-22-2015, 07:27 PM)raysorenson If you're going 1 piece, you need a sliding YOKE on the output shaft, lubed with egg YOLK. As I understand, a sliding yoke in the middle of the shaft, not the output shaft, will affect radial stability on a shaft long enough for the typical sedan. They're fine on jeeps and other 4x4's that take stubby drive shafts but not for us. A sliding yoke mounted in the shaft needs a larger diameter the longer the shaft gets. There's not enough room in the tunnel for the shifter and a 3" diameter shaft. Does that make any sense?
Ah well congrats on correcting my spelling. The shaft will infact, be a larger diameter than stock w123 and what shifter will I need to worry about genius?
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
04-23-2015, 06:01 PM
#432
As for the spelling, I'd prefer an asshole on the web correct me than I go around saying "yolk this" and "yolk that" at work in front of a bunch of colleagues who know better but won't correct me to my face. If you think I did you a bad turn, apologies.
raysorenson
04-23-2015, 06:01 PM #432The point was you need a splined output on the trans for a slip yoke on a 1 piece shaft that long.
As for the spelling, I'd prefer an asshole on the web correct me than I go around saying "yolk this" and "yolk that" at work in front of a bunch of colleagues who know better but won't correct me to my face. If you think I did you a bad turn, apologies.
05-17-2015, 04:44 AM
#433
(04-23-2015, 06:01 PM)raysorenson The point was you need a splined output on the trans for a slip yoke on a 1 piece shaft that long.
As for the spelling, I'd prefer an asshole on the web correct me than I go around saying "yolk this" and "yolk that" at work in front of a bunch of colleagues who know better but won't correct me to my face. If you think I did you a bad turn, apologies.
it was funny. No fucks given lol
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
05-17-2015, 04:44 AM #433(04-23-2015, 06:01 PM)raysorenson The point was you need a splined output on the trans for a slip yoke on a 1 piece shaft that long.
As for the spelling, I'd prefer an asshole on the web correct me than I go around saying "yolk this" and "yolk that" at work in front of a bunch of colleagues who know better but won't correct me to my face. If you think I did you a bad turn, apologies.
it was funny. No fucks given lol
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
05-17-2015, 04:57 AM
#434
![[Image: rsz_img_20150503_134115031_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/rsz_img_20150503_134115031_hdr.jpg)
Then I decided to see if the trans would behave and it did! So fuck it I started driving it again until I had time for the trans swap.
![[Image: rsz_1rsz_img_20150508_165337193_hdr.jpg]](http://i64.photobucket.com/albums/h183/foxcrf450rider/rsz_1rsz_img_20150508_165337193_hdr.jpg)
Until the other day I was 10 miles from home and it started running really weird. i popped the hood and some injector return lines were leaking I also checked the oil level and it was full... well as I started driving it was getting worse ...
Now it occurs to me that its running like its low on oil pressure. so long story short by the time I baby it home it acts like it is seizing. Well fuck me right? I triple check and there is plenty of oil in the pan but something must have happened (maybe with the new pickup)??? I don't know I'm so confused. I come out today, replaced the return line and start the bitch up and it acts like normal. I have no oil pressure gauge so I popped the fill cap and look at the cam. THERE IS oil squirting on it like normal but that may mean nothing who knows? I let it warm up a few min and bring up the idle (everything seemed fine at this point) and bam.... There's the rod knock. So guess I'm looking for a donor engine or will rebuild this fucker!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
05-17-2015, 04:57 AM #434So anyway I beat the dents out of my lower oil pan and replaced the oil pump pickup with a new one from the dealer because it was cracked.
Then I decided to see if the trans would behave and it did! So fuck it I started driving it again until I had time for the trans swap.
Until the other day I was 10 miles from home and it started running really weird. i popped the hood and some injector return lines were leaking I also checked the oil level and it was full... well as I started driving it was getting worse ...
Now it occurs to me that its running like its low on oil pressure. so long story short by the time I baby it home it acts like it is seizing. Well fuck me right? I triple check and there is plenty of oil in the pan but something must have happened (maybe with the new pickup)??? I don't know I'm so confused. I come out today, replaced the return line and start the bitch up and it acts like normal. I have no oil pressure gauge so I popped the fill cap and look at the cam. THERE IS oil squirting on it like normal but that may mean nothing who knows? I let it warm up a few min and bring up the idle (everything seemed fine at this point) and bam.... There's the rod knock. So guess I'm looking for a donor engine or will rebuild this fucker!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
05-17-2015, 06:21 AM
#435
I hope you find parts cheap nearby, but if not I know of a turbo short block (unknown miles but clean) that's soon to be available on the east coast.
'05 Jeep Liberty CRD - 160k
'06.5 VW Jetta TDI - 230k
'82 MB 300TD - 116k (motor going to raysorenson)
'81 MB 300TD - 195k (parting out)
'71 Jeep DJ5 - diesel conversion project
Damn! What a kick to the balls! Sorry to hear (the story and the knock)!
I hope you find parts cheap nearby, but if not I know of a turbo short block (unknown miles but clean) that's soon to be available on the east coast.
'05 Jeep Liberty CRD - 160k
'06.5 VW Jetta TDI - 230k
'82 MB 300TD - 116k (motor going to raysorenson)
'81 MB 300TD - 195k (parting out)
'71 Jeep DJ5 - diesel conversion project
05-17-2015, 12:25 PM
#438
(05-17-2015, 06:21 AM)CRD4x4 Damn! What a kick to the balls! Sorry to hear (the story and the knock)!
I hope you find parts cheap nearby, but if not I know of a turbo short block (unknown miles but clean) that's soon to be available on the east coast.
Thanks man I appreciate it, probly will keep the search here on the west to keep cost low but thanks!
(05-17-2015, 09:43 AM)atypicalguy I can put u in touch with a guy in phoenix with some motors.
Phoenix isn't too far away, only about six hours or so...
(05-17-2015, 11:35 AM)OM616 The video sounded more like valve train noise than a rod to me. You might just pull the cover and see if an adjustment nut came loose.
Ya it does but its definitely down in the lower end.. And it goes away at idle, that was just a shitty Snapchat video that I saved haha
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
05-17-2015, 12:25 PM #438(05-17-2015, 06:21 AM)CRD4x4 Damn! What a kick to the balls! Sorry to hear (the story and the knock)!
I hope you find parts cheap nearby, but if not I know of a turbo short block (unknown miles but clean) that's soon to be available on the east coast.
Thanks man I appreciate it, probly will keep the search here on the west to keep cost low but thanks!
(05-17-2015, 09:43 AM)atypicalguy I can put u in touch with a guy in phoenix with some motors.
Phoenix isn't too far away, only about six hours or so...
(05-17-2015, 11:35 AM)OM616 The video sounded more like valve train noise than a rod to me. You might just pull the cover and see if an adjustment nut came loose.
Ya it does but its definitely down in the lower end.. And it goes away at idle, that was just a shitty Snapchat video that I saved haha
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
05-17-2015, 12:30 PM
#439
That is why I am leaning towards rebuilding it if the parts are still OK (crank, rods, pistons, can, block) the other stuff like valves and sleeves are cheap and I'd rather have something fresh!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
05-17-2015, 12:30 PM #439This time around I for sure want something that I know or can verify history of... This will be the third engine for this car and while this engine was extremely clean the milage was somewhat unknown and I had ran it out of oil once before which I knew made it a ticking time bomb for some thing like this to happen. Honestly I'm surprised it lasted this long, I probably put this thing through more hell than most people out there or even on this forum!
That is why I am leaning towards rebuilding it if the parts are still OK (crank, rods, pistons, can, block) the other stuff like valves and sleeves are cheap and I'd rather have something fresh!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
05-17-2015, 09:28 PM
#440
atypicalguy
05-17-2015, 09:28 PM #440The rebuild sounds attractive, but expensive. You could have a 606 for that.
05-17-2015, 09:55 PM
#441
______________________________
'85 300D ~ 381,XXX miles, HD Bilstein shocks, 27.50x8.50x14R General Grabber AT2 tires, 4 E-Code headlight upgrade with 90w/130w bulbs, boost turned up, new timing chain, and injectors. Brought back from the dead and the hell of WVO! SOLD
'85 CJ7 ~ OM617 swap, Taurus electric fan, T5 trans, Dana 300, 4.88 R&P, Mile Marker locking hubs, ALDA removed, MKII hybrid boost controller, Greazzer's upgraded overflow valve, AMC 20 rear disk brake conversion, Aussie locked with 33's and 5" Rough Country lift.
That's what I'm thinking as well. Seems like for the money you could keep the MB diesel factor and scrounge up some more power.
______________________________
'85 300D ~ 381,XXX miles, HD Bilstein shocks, 27.50x8.50x14R General Grabber AT2 tires, 4 E-Code headlight upgrade with 90w/130w bulbs, boost turned up, new timing chain, and injectors. Brought back from the dead and the hell of WVO! SOLD
'85 CJ7 ~ OM617 swap, Taurus electric fan, T5 trans, Dana 300, 4.88 R&P, Mile Marker locking hubs, ALDA removed, MKII hybrid boost controller, Greazzer's upgraded overflow valve, AMC 20 rear disk brake conversion, Aussie locked with 33's and 5" Rough Country lift.
05-18-2015, 03:37 AM
#442
(05-17-2015, 09:28 PM)atypicalguy The rebuild sounds attractive, but expensive. You could have a 606 for that.
(05-17-2015, 09:55 PM)turbojeep That's what I'm thinking as well. Seems like for the money you could keep the MB diesel factor and scrounge up some more power.
Idk though... You guys think? An OM606 would be, well, awesome! But nothing I have now works with that... I'm back to buying a new turbo fabbing intake parts and exhaust parts and all that stuff....
I'm thinking sleeves, regrind on the crank and a rod, bearings, rimgs, valves and porting I would be done for under $1k and have a fresh motor that I don't have to worry about "what were the previous 2xx,xxx miles like?"
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
05-18-2015, 03:37 AM #442(05-17-2015, 09:28 PM)atypicalguy The rebuild sounds attractive, but expensive. You could have a 606 for that.
(05-17-2015, 09:55 PM)turbojeep That's what I'm thinking as well. Seems like for the money you could keep the MB diesel factor and scrounge up some more power.
Idk though... You guys think? An OM606 would be, well, awesome! But nothing I have now works with that... I'm back to buying a new turbo fabbing intake parts and exhaust parts and all that stuff....
I'm thinking sleeves, regrind on the crank and a rod, bearings, rimgs, valves and porting I would be done for under $1k and have a fresh motor that I don't have to worry about "what were the previous 2xx,xxx miles like?"
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
05-18-2015, 10:16 AM
#443
All the same, I'd suggest you do some browsing to see what it would run you to make the jump to the OM606. You could sell off your prechambers, your IP (it has 10mm elements, right?), exhaust, etc... The intercooler and trans can be made to for without much trouble, I'd think.
______________________________
'85 300D ~ 381,XXX miles, HD Bilstein shocks, 27.50x8.50x14R General Grabber AT2 tires, 4 E-Code headlight upgrade with 90w/130w bulbs, boost turned up, new timing chain, and injectors. Brought back from the dead and the hell of WVO! SOLD
'85 CJ7 ~ OM617 swap, Taurus electric fan, T5 trans, Dana 300, 4.88 R&P, Mile Marker locking hubs, ALDA removed, MKII hybrid boost controller, Greazzer's upgraded overflow valve, AMC 20 rear disk brake conversion, Aussie locked with 33's and 5" Rough Country lift.
$1K isn't too bad. If you could get it back together for close to that, rebuild sounds like the way to go.
All the same, I'd suggest you do some browsing to see what it would run you to make the jump to the OM606. You could sell off your prechambers, your IP (it has 10mm elements, right?), exhaust, etc... The intercooler and trans can be made to for without much trouble, I'd think.
______________________________
'85 300D ~ 381,XXX miles, HD Bilstein shocks, 27.50x8.50x14R General Grabber AT2 tires, 4 E-Code headlight upgrade with 90w/130w bulbs, boost turned up, new timing chain, and injectors. Brought back from the dead and the hell of WVO! SOLD
'85 CJ7 ~ OM617 swap, Taurus electric fan, T5 trans, Dana 300, 4.88 R&P, Mile Marker locking hubs, ALDA removed, MKII hybrid boost controller, Greazzer's upgraded overflow valve, AMC 20 rear disk brake conversion, Aussie locked with 33's and 5" Rough Country lift.
05-18-2015, 11:42 AM
#444
Looks like you've not driven much with the damaged bearings. Could be a cheap fix, if the cylinder bores & crank journals are still within specification. Hone, re-ring, new bearings and on you go! Doesn't always have to be a "full" rebuild (it's nice, no doubt about that!).
DiseaselWeasel
05-18-2015, 11:42 AM #444Well, maybe all you need is a new set of smal end bearings... Looks like you've not driven much with the damaged bearings. Could be a cheap fix, if the cylinder bores & crank journals are still within specification. Hone, re-ring, new bearings and on you go! Doesn't always have to be a "full" rebuild (it's nice, no doubt about that!).
05-19-2015, 03:20 PM
#445
(05-18-2015, 10:16 AM)turbojeep $1K isn't too bad. If you could get it back together for close to that, rebuild sounds like the way to go.
All the same, I'd suggest you do some browsing to see what it would run you to make the jump to the OM606. You could sell off your prechambers, your IP (it has 10mm elements, right?), exhaust, etc... The intercooler and trans can be made to for without much trouble, I'd think.
(05-18-2015, 11:42 AM)DiseaselWeasel Well, maybe all you need is a new set of smal end bearings...
Good points gentlemen! I will know in a few days time what direction I'll be headed!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
05-19-2015, 03:20 PM #445(05-18-2015, 10:16 AM)turbojeep $1K isn't too bad. If you could get it back together for close to that, rebuild sounds like the way to go.
All the same, I'd suggest you do some browsing to see what it would run you to make the jump to the OM606. You could sell off your prechambers, your IP (it has 10mm elements, right?), exhaust, etc... The intercooler and trans can be made to for without much trouble, I'd think.
(05-18-2015, 11:42 AM)DiseaselWeasel Well, maybe all you need is a new set of smal end bearings...
Good points gentlemen! I will know in a few days time what direction I'll be headed!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
05-20-2015, 09:02 PM
#446
(05-19-2015, 03:20 PM)Captain America(05-18-2015, 10:16 AM)turbojeep $1K isn't too bad. If you could get it back together for close to that, rebuild sounds like the way to go.
All the same, I'd suggest you do some browsing to see what it would run you to make the jump to the OM606. You could sell off your prechambers, your IP (it has 10mm elements, right?), exhaust, etc... The intercooler and trans can be made to for without much trouble, I'd think.
(05-18-2015, 11:42 AM)DiseaselWeasel Well, maybe all you need is a new set of smal end bearings...
points gentlemen! I will know in a few days time what direction I'll be headed!
You don't know much until you have it apart.
atypicalguy
05-20-2015, 09:02 PM #446(05-19-2015, 03:20 PM)Captain America(05-18-2015, 10:16 AM)turbojeep $1K isn't too bad. If you could get it back together for close to that, rebuild sounds like the way to go.
All the same, I'd suggest you do some browsing to see what it would run you to make the jump to the OM606. You could sell off your prechambers, your IP (it has 10mm elements, right?), exhaust, etc... The intercooler and trans can be made to for without much trouble, I'd think.
(05-18-2015, 11:42 AM)DiseaselWeasel Well, maybe all you need is a new set of smal end bearings...
points gentlemen! I will know in a few days time what direction I'll be headed!
You don't know much until you have it apart.
05-20-2015, 11:50 PM
#447
(05-20-2015, 09:02 PM)atypicalguy You don't know much until you have it apart.
Exactly, It's all speculation at this point. If I dont go to the river this weekend I will have it out and apart! and be posting pics for sure
STAY TUNED!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
05-20-2015, 11:50 PM #447(05-20-2015, 09:02 PM)atypicalguy You don't know much until you have it apart.
Exactly, It's all speculation at this point. If I dont go to the river this weekend I will have it out and apart! and be posting pics for sure
STAY TUNED!
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
05-22-2015, 04:15 PM
#449
(05-22-2015, 06:28 AM)DanielK Pop your oil pump off and give it a good look. You might've gotten a shit pump that is temperamental.
Even if that's the case I'm past the point of saving the engine without pulling it
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
Captain America
05-22-2015, 04:15 PM #449(05-22-2015, 06:28 AM)DanielK Pop your oil pump off and give it a good look. You might've gotten a shit pump that is temperamental.
Even if that's the case I'm past the point of saving the engine without pulling it
1982 300D Turbo ... 3,6xxlbs, No fan, No AC, Hood Stack, No ALDA, No rear bumper and stuffed front, A/W Intercooled, Injectors by Greezer and HUGE Pre-Chambers with help from OM616 & Simpler=Better, Fuel Cranked up, 60 Trim Compressor wheel, EGT, EMP, Boost 50" Rigid Radius bar on roof Aux tank for a total of 48 Gal Of Diesel! Odyssey PC-1750 Battery in trunk, 27"x8.5"/R14 Maxxis BigHorn Mud Terrains, In June '14 issue of Off Road Mag
AX15 Jeep Trans swap in progress....
05-23-2015, 07:53 PM
#450
During my rebuild I bought two extra shortblocks and have a few decent internal parts left over. If you rebuild what you got and need some of those unobtanium hard parts, hit me up, you can have them.
Well fuck, that sucks man. Heres to ya getting something back in it and rolling soon :beers:
During my rebuild I bought two extra shortblocks and have a few decent internal parts left over. If you rebuild what you got and need some of those unobtanium hard parts, hit me up, you can have them.
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Users browsing this thread:
1 Guest(s)
1 Guest(s)