OM606 Boat engine
OM606 Boat engine
03-28-2016, 01:11 AM
#1
first post on here and looking for a little help.
I have built a marine engine with 250hp took off electronic pump and replace with mech one but finding it hard to get throttle cable from boat controls to fit to meck pump. any one done this??
Thanks
Hi All
first post on here and looking for a little help.
I have built a marine engine with 250hp took off electronic pump and replace with mech one but finding it hard to get throttle cable from boat controls to fit to meck pump. any one done this??
Thanks
03-29-2016, 01:32 AM
#2
(03-28-2016, 01:11 AM)Carlos69 Hi All
first post on here and looking for a little help.
I have built a marine engine with 250hp took off electronic pump and replace with mech one but finding it hard to get throttle cable from boat controls to fit to meck pump. any one done this??
Thanks
On my Jeep conversions, I make a plate to go were the fuel heater was in the head and make a bracket to hold the cable and then put a carb style ball on the IP linkage. Just snap on the cable. Also made a bracket for a stiffer spring.
Attached Files
Image(s)(03-28-2016, 01:11 AM)Carlos69 Hi All
first post on here and looking for a little help.
I have built a marine engine with 250hp took off electronic pump and replace with mech one but finding it hard to get throttle cable from boat controls to fit to meck pump. any one done this??
Thanks
On my Jeep conversions, I make a plate to go were the fuel heater was in the head and make a bracket to hold the cable and then put a carb style ball on the IP linkage. Just snap on the cable. Also made a bracket for a stiffer spring.
Attached Files
Image(s)
06-12-2016, 05:49 PM
#5
87 300SDL OM606 swapped HE351VE 722.633 swapped, Crower cams, KM valvesprings
76 300TD custom lots of stuff
06 Mercedes CL65 AMG 619 WHP, http://TurboTims.com
Maybe have your cable pull a smaller more flexible cable.
87 300SDL OM606 swapped HE351VE 722.633 swapped, Crower cams, KM valvesprings
76 300TD custom lots of stuff
06 Mercedes CL65 AMG 619 WHP, http://TurboTims.com
06-12-2016, 06:09 PM
#6
(03-29-2016, 01:32 AM)zeeman(03-28-2016, 01:11 AM)Carlos69 Hi All
first post on here and looking for a little help.
I have built a marine engine with 250hp took off electronic pump and replace with mech one but finding it hard to get throttle cable from boat controls to fit to meck pump. any one done this??
Thanks
On my Jeep conversions, I make a plate to go were the fuel heater was in the head and make a bracket to hold the cable and then put a carb style ball on the IP linkage. Just snap on the cable. Also made a bracket for a stiffer spring.
Zeeman you could probably sell a few of those brackets and cables. I would buy one. The dieselpumpuk guys have one that they want a lot of money for, and almost as much again for shipping.
atypicalguy
06-12-2016, 06:09 PM #6(03-29-2016, 01:32 AM)zeeman(03-28-2016, 01:11 AM)Carlos69 Hi All
first post on here and looking for a little help.
I have built a marine engine with 250hp took off electronic pump and replace with mech one but finding it hard to get throttle cable from boat controls to fit to meck pump. any one done this??
Thanks
On my Jeep conversions, I make a plate to go were the fuel heater was in the head and make a bracket to hold the cable and then put a carb style ball on the IP linkage. Just snap on the cable. Also made a bracket for a stiffer spring.
Zeeman you could probably sell a few of those brackets and cables. I would buy one. The dieselpumpuk guys have one that they want a lot of money for, and almost as much again for shipping.
Users browsing this thread:
3 Guest(s)
3 Guest(s)
Users browsing this thread:
3 Guest(s)
3 Guest(s)