STD Tuning Engine OM617 turbo outlet flange

OM617 turbo outlet flange

OM617 turbo outlet flange

 View a Printable Version
 
  • 0 Vote(s) - 0 Average
 
R-3350
Find
Dreaming of compounds

182
07-20-2016, 12:42 PM #1
Reply
Reply
i recently got a 6CM housing HE221W and just wanted to verify that the outlet on the stock Garrett t3 to the down pipe is a 3" v-band flange. also if anyone has a HE221W how did you end up adapting the compressor discharge to the intake manifold?
R-3350
07-20-2016, 12:42 PM #1

i recently got a 6CM housing HE221W and just wanted to verify that the outlet on the stock Garrett t3 to the down pipe is a 3" v-band flange. also if anyone has a HE221W how did you end up adapting the compressor discharge to the intake manifold?

Reply
Reply
awsrock
Find
300SDL / HX30 / 90cc

179
07-20-2016, 12:47 PM #2
Reply
Reply
I have an HX30 and the outlet was a special Holset Vband that was 2.75 inch. My 603 stock downpipe is only 2.5 or so..
awsrock
07-20-2016, 12:47 PM #2

I have an HX30 and the outlet was a special Holset Vband that was 2.75 inch. My 603 stock downpipe is only 2.5 or so..

Reply
Reply
NiTeC
Website Find
Naturally-aspirated

22
07-20-2016, 01:50 PM #3
Reply
Reply
the He221 uses a smaller v-band on the compressor outlet that the Hx30...the 30 uses the same elbow as the 35, 351, 40 etc.

I used a 2.5" downpipe with my 221...my exhaust guy made the flange and used a gasket in between...I used the original Cummins clamps for both the compressor and turbine outlets...

you can kinda see the compressor outlet here:

[Image: IMG_1565_zps829b3e69.jpg]

and the turbo outlet here:

[Image: 20160121_162817_zpsgd4oeuce.jpg]
This post was last modified: 07-20-2016, 01:52 PM by NiTeC.
NiTeC
07-20-2016, 01:50 PM #3

the He221 uses a smaller v-band on the compressor outlet that the Hx30...the 30 uses the same elbow as the 35, 351, 40 etc.

I used a 2.5" downpipe with my 221...my exhaust guy made the flange and used a gasket in between...I used the original Cummins clamps for both the compressor and turbine outlets...

you can kinda see the compressor outlet here:

[Image: IMG_1565_zps829b3e69.jpg]

and the turbo outlet here:

[Image: 20160121_162817_zpsgd4oeuce.jpg]

Reply
Reply
R-3350
Find
Dreaming of compounds

182
07-20-2016, 04:26 PM #4
Reply
Reply
i have an exhaust flange for the HE221W that i got a local shop to make for me its a 3" v-band that has nothing restricting the turbine outlet or the waste gate its just a 5/8" strip of 1/2" mild steel with the 4 bolt pattern and the v-band. i was wondering what the flange is on the flex pipe going to the stock t3 garrett is. i have heard its a 3" v-band that reduces to the 2.5 DP. if not ill just get an adapter. as for the compressor im not sure that elbow will clear my fender wall i need something that makes a pretty tight 90.
R-3350
07-20-2016, 04:26 PM #4

i have an exhaust flange for the HE221W that i got a local shop to make for me its a 3" v-band that has nothing restricting the turbine outlet or the waste gate its just a 5/8" strip of 1/2" mild steel with the 4 bolt pattern and the v-band. i was wondering what the flange is on the flex pipe going to the stock t3 garrett is. i have heard its a 3" v-band that reduces to the 2.5 DP. if not ill just get an adapter. as for the compressor im not sure that elbow will clear my fender wall i need something that makes a pretty tight 90.

Reply
Reply
 View a Printable Version
 
  • 0 Vote(s) - 0 Average
Users browsing this thread:
 1 Guest(s)
Users browsing this thread:
 1 Guest(s)