716.630 gear linkage mods
716.630 gear linkage mods
The big selector rod needs to be shortened by 10cm which is no problem.
I'm a bit stuck with the cable at the side, it only ever seems to move when Reverse on the gear selector is selected.
I have bought 4 linkages and the bit between the cable and box is missing on all of them
Any help, is the cable required?
I have a 716.630 mated to an om605 that I've fitted to the car.
The big selector rod needs to be shortened by 10cm which is no problem.
I'm a bit stuck with the cable at the side, it only ever seems to move when Reverse on the gear selector is selected.
I have bought 4 linkages and the bit between the cable and box is missing on all of them
Any help, is the cable required?
On the end of the cable is an adjuster, although I doubt that with 100mm shortening you will be able to achieve this without shortening the cable itself.
the bracket on the side which receives the cable, runs through 2 pivot linkages and rotates through 90 degrees, to which a connecting rod joins the selector rod to the cable.
The purpose is to allow engagement of reverse and correct spacing of the H pattern, with the appropriate centre position.
IF the cable is not correctly set, the shift lever will make it all but impossible to select all gears. usually 5 & 6 go missing, because the cable prevents the full rotation of the selector arm.
Yes, the cable is required.
On the end of the cable is an adjuster, although I doubt that with 100mm shortening you will be able to achieve this without shortening the cable itself.
the bracket on the side which receives the cable, runs through 2 pivot linkages and rotates through 90 degrees, to which a connecting rod joins the selector rod to the cable.
The purpose is to allow engagement of reverse and correct spacing of the H pattern, with the appropriate centre position.
IF the cable is not correctly set, the shift lever will make it all but impossible to select all gears. usually 5 & 6 go missing, because the cable prevents the full rotation of the selector arm.
I also got a small cable made up but the original with metal elbow cut off did a better job.
or look into the w204 shifter setup.
I may change to this when the gearbox is out.
Its a single bar that rotates for left and right instead of the cable section.
i cut the metal elbow off the cable to help with it.
I also got a small cable made up but the original with metal elbow cut off did a better job.
or look into the w204 shifter setup.
I may change to this when the gearbox is out.
Its a single bar that rotates for left and right instead of the cable section.
if you fit a 716 Gearbox in an w201, you just take the Cable from an w208 CLK 230 with 6-Speed Gearbox.
Cost is about 30 € new at your local MB-Dealer.
Its a straigt bolt-on.
Greets
Max
______________________________________________________________
93´ W124 300TDT -> OM606.962 / RS 203 Dieselmeken 7,5mm 210cc / KKK K14 / Stock Transmission / 2,65 ASD
89´ 190D 2.5 Turbo -> OM605.960 / Dieselmeken 7,5mm 180cc / Holset HX30 Super / 716. 654 6-Speed / 2,87 Rear Axle
Hi,
if you fit a 716 Gearbox in an w201, you just take the Cable from an w208 CLK 230 with 6-Speed Gearbox.
Cost is about 30 € new at your local MB-Dealer.
Its a straigt bolt-on.
Greets
Max
______________________________________________________________
93´ W124 300TDT -> OM606.962 / RS 203 Dieselmeken 7,5mm 210cc / KKK K14 / Stock Transmission / 2,65 ASD
89´ 190D 2.5 Turbo -> OM605.960 / Dieselmeken 7,5mm 180cc / Holset HX30 Super / 716. 654 6-Speed / 2,87 Rear Axle
(02-15-2017, 10:54 AM)seanyt i cut the metal elbow off the cable to help with it.
I also got a small cable made up but the original with metal elbow cut off did a better job.
or look into the w204 shifter setup.
I may change to this when the gearbox is out.
Its a single bar that rotates for left and right instead of the cable section.
I also thought about it and I wanted to do it...but
How can you solve the fitting problem in the gearbox,the fit is different for the 2 shifter in gearbox..?
bruno_pinho
02-16-2017, 03:03 PM #7(02-15-2017, 10:54 AM)seanyt i cut the metal elbow off the cable to help with it.
I also got a small cable made up but the original with metal elbow cut off did a better job.
or look into the w204 shifter setup.
I may change to this when the gearbox is out.
Its a single bar that rotates for left and right instead of the cable section.
I also thought about it and I wanted to do it...but
How can you solve the fitting problem in the gearbox,the fit is different for the 2 shifter in gearbox..?
______________________________________________________________
93´ W124 300TDT -> OM606.962 / RS 203 Dieselmeken 7,5mm 210cc / KKK K14 / Stock Transmission / 2,65 ASD
89´ 190D 2.5 Turbo -> OM605.960 / Dieselmeken 7,5mm 180cc / Holset HX30 Super / 716. 654 6-Speed / 2,87 Rear Axle
No, i only have expierence with w201.
______________________________________________________________
93´ W124 300TDT -> OM606.962 / RS 203 Dieselmeken 7,5mm 210cc / KKK K14 / Stock Transmission / 2,65 ASD
89´ 190D 2.5 Turbo -> OM605.960 / Dieselmeken 7,5mm 180cc / Holset HX30 Super / 716. 654 6-Speed / 2,87 Rear Axle
3 Guest(s)
3 Guest(s)