722.6 ML Class Gearbox output splines

STD Tuning Drivetrain 722.6 ML Class Gearbox output splines

View a Printable Version

0 Vote(s) - 0 Average

ross

GT2256V

109

04-06-2017, 06:28 AM #1

Does anyone on here know the size of the output splines on an ML class version of the 722.6? Or know where I might find it?

Thanks in advance!

ross

04-06-2017, 06:28 AM #1

Does anyone on here know the size of the output splines on an ML class version of the 722.6? Or know where I might find it?

Thanks in advance!

whipplem104

Holset

559

04-06-2017, 07:56 AM #2

are you asking about the transmission shaft or the output that bolts on??

whipplem104

04-06-2017, 07:56 AM #2

are you asking about the transmission shaft or the output that bolts on??

ross

GT2256V

109

04-06-2017, 08:14 AM #3

(04-06-2017, 07:56 AM)whipplem104 are you asking about the transmission shaft or the output that bolts on??

The output that bolts on, the ~50ish mm diameter female spline.

ross

04-06-2017, 08:14 AM #3

(04-06-2017, 07:56 AM)whipplem104 are you asking about the transmission shaft or the output that bolts on??

The output that bolts on, the ~50ish mm diameter female spline.

whipplem104

Holset

559

04-06-2017, 10:48 AM #4

Well normally you measure diameter and count the splines. So I would say it is 55mm 26 spline. It might be 54mm. I do not have my good calipers here today. Just used some brake calipers
Splines are really standard so you should be able to find the standard sizes

whipplem104

04-06-2017, 10:48 AM #4

ross

GT2256V

109

04-07-2017, 01:50 AM #5

Yeah, but there are all sorts of shapes of spline, lots of different standards.

ross

04-07-2017, 01:50 AM #5

Yeah, but there are all sorts of shapes of spline, lots of different standards.

whipplem104

Holset

559

04-07-2017, 08:00 AM #6

What are you trying to find out if it fits?

whipplem104

04-07-2017, 08:00 AM #6

What are you trying to find out if it fits?

ross

GT2256V

109

04-07-2017, 09:07 AM #7

I need the original specification of the spline so I can have a spline machined to match it on my adaptor shaft.

ross

04-07-2017, 09:07 AM #7

I need the original specification of the spline so I can have a spline machined to match it on my adaptor shaft.

whipplem104

Holset

559

04-07-2017, 04:15 PM #8

Ok,
It is the same as the JEEP srt8 and the wranglers with the nv t cases. You might find more info looking for those.

whipplem104

04-07-2017, 04:15 PM #8

Ok,
It is the same as the JEEP srt8 and the wranglers with the nv t cases. You might find more info looking for those.

ross

GT2256V

109

04-19-2017, 08:08 AM #9

Thanks Whipple Smile

.

I've actually contacted Mercedes UK, and I've had a response! Smile

ross

04-19-2017, 08:08 AM #9

Thanks Whipple Smile .

I've actually contacted Mercedes UK, and I've had a response! Smile

matfield

GT2256V

104

06-29-2017, 05:39 AM #10

Ross... would you have a measurement from bell housing to the rear output flange that bolts onto the Merc transfer box?

Thanks

Mat

matfield

06-29-2017, 05:39 AM #10

Ross... would you have a measurement from bell housing to the rear output flange that bolts onto the Merc transfer box?

Thanks

Mat

ross

GT2256V

109

07-04-2017, 03:47 PM #11

(06-29-2017, 05:39 AM)matfield Ross... would you have a measurement from bell housing to the rear output flange that bolts onto the Merc transfer box?

Thanks

Mat

The back face where the adaptor bolts on? There's a small link bit/adaptor on the ML box.

I haven't got the measurement to hand, but I can get it for you?

ross

07-04-2017, 03:47 PM #11

(06-29-2017, 05:39 AM)matfield Ross... would you have a measurement from bell housing to the rear output flange that bolts onto the Merc transfer box?

Thanks

Mat

The back face where the adaptor bolts on? There's a small link bit/adaptor on the ML box.

I haven't got the measurement to hand, but I can get it for you?

View a Printable Version

0 Vote(s) - 0 Average

Users browsing this thread:
2 Guest(s)